Samsung Television UN5500 User Manual

							24
Failed Wired Connection
No network cable found Try Now Try Now
Make sure the network cable is plugged in. If it is connected, make sure the router is turned on. If it is 
on, try turning it off and on again.
IP auto setting failed Try Now
Perform the following or set the IP address manually from IP Settings.
11 Ensure that the DHCP server is enabled on the router and reset the router.
21 If this does not work, contact your Internet Service Provider for more information.
Unable to connect to the network Try Now
Check the following:
11 Check the IP Settings  settings.
21 Ensure that the DHCP server is enabled on the router and unplug and then plug the router back in.
31 If this does not work, contact your Internet Service Provider for more information.
Connected to a local network, but not to the Internet Try Now
11 Make sure that the Internet LAN cable is connected to the router's external LAN port.
21 Check the DNS settings under  IP Settings.
31 If the problem persists, contact your Internet Service Provider.
Network setup complete, but unable to connect to the Internet Try Now
If the problem persists, contact your Internet Service Provider. 
						

							2425
Wireless Network Setup
Screen Menu > Network > Network Settings
Network
Network Status
Network Settings
Wi-Fi Direct
AllShare Settings
Device Name  [TV]Samsung LE...
 
"The displayed image may differ depending on the model.
Automatic Wireless Network Setup
Connect the TV to the Internet via a wireless router. Check the wireless router's SSID and security 
key settings before attempting to connect. The security key can be found on the wireless router's 
configuration screen.
11 Setting  Network type  to Wireless  automatically displays a list of available wireless networks.
21 Select the network (SSID) you wish to connect to. If the desired wireless router doesn't appear in 
the list, select  Add Network and enter the network's SSID manually.
31 Enter the security key and select  Done. If the selected network is not security-enabled, the TV will 
attempt a connection right away.
41 The TV attempts to connect to the network. A confirmation message is then shown once a 
connection is established. Select  OK to proceed. If the attempt fails, try again or connect 
manually. 
						

							26
Manual Wireless Network Setup
If the network requires a static IP address, enter the IP address, subnet mask, gateway and DNS values 
to connect to the network manually. To get the IP address, subnet mask, gateway and DNS values, 
contact your Internet Service Provider (ISP). Refer to the "Dynamic versus Static IP Addresses" for 
more information.
11 Setting Network type  to Wireless  automatically displays a list of available wireless networks.
Network Settings
Select your network type.
Network type Wireless
Wireless network
AP0000
AP0001
Add Network
You can connect your TV to the 
internet. Please select which 
wireless network to use.
RefreshWPS(PBC)
21 Select the network (SSID) you wish to connect to. If the desired wireless router doesn't appear in 
the list, select  Add Network and enter the network's SSID manually.
31 Enter the security key and select  Done. If the selected network is not security-enabled, the TV will 
attempt a connection right away. 
						

							2627
41 Select Stop when the TV attempts to connect to the network. Once the network connection has 
been interrupted, select IP Settings .
Network Settings
Connection verification cancelled.
Wireless network connection test is stopped.
Change Network IP SettingsRetryClose
51 From the IP Settings  screen, set IP Setting to Enter manually , enter IP Address , Subnet Mask, 
Gateway, and the DNS Server values, and then select  OK.
IP Settings
IP Setting Enter manually
IP Address  0.0.0.0
Subnet Mask 0.0.0.0
Gateway  0.0.0.0
DNS Setting  Enter manually
DNS Server  0.0.0.0
OKCancel
61 The TV attempts to connect to the network again using the specified settings. A confirmation 
message is then shown once a connection is established. Select  OK to proceed. 
						

							28
Using the WPS Button
If the router has a WPS push button, you can use it to connect the TV to the router automatically. WPS 
automatically configures the SSID and WPA key settings.
11 Setting Network type  to Wireless  automatically displays a list of available wireless networks.
21 Select WPS(PBC) and then press the router's WPS button within two minutes.
31 The TV automatically acquires the SSID and security key settings and connects to the network. A 
confirmation message is then shown once a connection is established. Select  OK to proceed.
Failed Wireless Connection
Wireless network connection failed, or no wireless router selected. Try Now Try Now
Go to Network Settings and select the correct router.
Unable to connect to a wireless router Try Now Try Now
Check the following:
11 Check that the router is turned on, and if it is, turn it off and on again.
21 Enter the correct security key if required.
IP auto setting failed Try Now
Perform the following or set the IP address manually from  IP Settings.
11 Make sure that the DHCP server is enabled on the router and unplug and plug the router back in.
21 Enter the correct security key if required.
31 If this does not work, contact your Internet Service Provider for more information. 
						

							2829
Unable to connect to the network Try Now
Check the following:
11 Check the IP Settings settings.
21 Enter the correct security key if required.
31 If this does not work, contact your Internet Service Provider for more information.
Connected to a local network, but not to the Internet Try Now
11 Make sure that the Internet LAN cable is connected to the router's external LAN port.
21 Check the DNS settings under  IP Settings.
31 If the problem persists, contact your Internet Service Provider.
Network setup complete, but unable to connect to the Internet Try Now
If the problem persists, contact your Internet Service Provider.
Dynamic versus Static IP Addresses
If the network requires a dynamic IP address, use an ADSL modem or router that supports the 
Dynamic Host Configuration Protocol (DHCP). Modems and routers that support DHCP automatically 
provide the IP address, subnet mask, gateway and DNS values the TV needs to access the Internet, so 
they do not have to be entered manually. Most home networks use a dynamic IP address.
If the network requires a static IP address, enter the IP address, subnet mask, gateway, and DNS values 
manually when setting up the network connection. To get the IP address, subnet mask, gateway and 
DNS values, contact your Internet Service Provider (ISP).
If the network requires a static IP address, use an ADSL modem that supports DHCP. ADSL modems 
that support DHCP also allow static IP addresses. 
						

							30
Checking the Network Status
Screen Menu > Network > Network Status  Try Now
Network
Network Status
Network Settings
Wi-Fi Direct
AllShare Settings
Device Name  [TV]Samsung LE...
 
"The displayed image may differ depending on the model.
View the current network and Internet status.
Mobile Device Connection
Network
Network Status
Network Settings
Wi-Fi Direct
AllShare Settings
Device Name  [TV]Samsung LE...
 
"The displayed image may differ depending on the model.
You can either directly connect a mobile device to the TV with no need for a wireless router or connect 
them on the same network to play media files from the mobile device on the TV. 
						

							3031
Wi-Fi Direct
Screen Menu > Network > Wi-Fi Direct Try Now
Connect a mobile device that supports Wi-Fi Direct to the TV without using a wireless router.
11 Enable Wi-Fi Direct on the mobile device and then launch  Wi-Fi Direct. The TV automatically 
scans for and displays a list of available devices. The TV's name also appears on the mobile 
device.
21 Select the device from the list to initiate a connection. If a connection request is made by the 
TV, a permission message appears on the mobile device and vice versa. Accept the request to 
connect the mobile device to the TV.
AllShare Settings
Screen Menu >  Network > AllShare Settings
This TV can play media files from computers or other DLNA-enabled devices connected to the TV via 
a network. For details, see "Using Networked External Storage Devices".
In addition, this TV can be used as a display for mobile devices, including smartphones and tablets. 
For details, see "Screen Mirroring".
Rename the TV
Screen Menu >  Network > Device Name Try Now
Assign a unique name for your TV. The assigned name appears on the external devices connected to 
the TV via the network. 
						

							32
Controlling the TV
Smart Touch Control
Smart Touch Control is available only with PDP 5500 series and LED 6400 series or higher.
The Smart Touch Control makes it easier and more convenient to use the TV. For example, you can 
use the remote control's built-in touch pad to move the focus and make selections as you would on a 
computer using a mouse. In addition, you can use the virtual remote panel displayed on the screen to 
change channels, play media files, and access favorites.
Inserting the Batteries (AAA X 2)
11 Slightly lift the battery cover by pulling the strap or using a plastic card (e.g. a credit card). Next, 
pull on the cover’s notch with a fingernail to remove the cover completely.
21 Insert 2 AAA batteries, making sure to align the positive and negative ends correctly.
31 Align the battery cover with the back of the remote control and press down along the edges until 
it is cleanly attached to the remote control.
Connecting to the TV
In order to operate the TV using a Smart Touch Control, you must first pair it to the TV via Bluetooth. 
However, the Smart Touch Control is only available for the paired Samsung TV.
11 To turn on the TV, point the Smart Touch Control at the remote control receiver of the TV and 
press the  TV button. The remote control receiver's location may vary depending on the model.
21 A Bluetooth icon will appear at the bottom left of the screen as shown below. The TV will then 
attempt to connect to the Smart Touch Control automatically.
 
						

							3233
Reconnecting the Smart Touch Control
If you need to reestablish the connection between the TV and the Smart Touch Control unit, press the 
pairing button at the back of the Smart Touch Control.

The pairing button can be accessed by removing the Smart Touch Control's battery cover. Pressing the 
pairing button automatically reestablishes the connection between the control and the TV.
Battery Low Alarm
If the battery becomes low while using the Smart Touch Control, the following alarm window blinks 
and appears at the bottom of the left screen. If the alarm window pops up, replace the batteries of the 
Smart Touch Control. Use alkaline batteries for longer usage.