Samsung Syncmaster T200g User Manual

							Others
 
 
Stand Base     Note
Cleaning Cloth is only provided for highly polished black products as a product feature.
Your Monitor
Initial Settings Select the language using the up or down key.
The displayed content will disappear after 40 seconds.
Turn the Power button off and on. It will be displayed again.
It 
can 
be displayed up to three (3) times. Make sure to adjust the resolution of your PC before reaching
the maximum count.  Note
The resolution displayed on the screen is the optimal resolution for this product.
Adjust your PC resolution so that it is the same as the optimal resolution for this product.
Front Introduction
10
 
						

							MENU button [MENU/ ]
Opens  the 
on-screen menu and exits from the menu. Also use to exit the OSD menu
or return to the previous menu. Brightness button [ ]
When OSD is not on the screen, push the button to adjust brightness.
>> Click here to see an animation clip Customized Key[ ]
You  can 

customize key assignment for the Custom button according to your pref-
erences.  Note
You  can 

configure the customized key for a required function via  Setup > Cus-
tomized Key. Adjust buttons [ ]
These buttons allow you to adjust items in the menu. Enter button [ ] / SOURCE button
Activates a highlighted menu item.
Push  the 

' /SOURCE', 
then selects the video signal while the OSD is off. (When
the  /SOURCE 
button is pressed to change the input mode, a message appears
in 

the upper left of the screen displaying the current mode -- analog or digital input
signal.)  Note
If  you 

select the digital mode, you must connect your monitor to the graphic card's
DVI port using the DVI cable.
>> Click here to see an animation clip AUTO button
Use this button for auto adjustment.
>> Click here to see an animation clip
Power button [ ]
Use this button for turning the monitor on and off.  Note
The button to the right of the monitor are touch-sensitive buttons.
Touch a button lightly with your finger.
Power Indicator
This  light 

glows blue during normal operation, and blinking blue once as the mon-
itor saves your adjustments. Introduction
11
 
						

							 Note
See  PowerSaver 
described in the manual for further information regarding power
saving functions. For energy conservation, turn your monitor OFF when it is not
needed or when leaving it unattended for long periods.
Rear  Note
The configuration at the back of the monitor may vary from product to product. POWER port
Connect 
the 

power  cord  for  your  monitor  to  the  POWER  port  on  the  back  of  the
monitor. DVI IN port
Connect the DVI Cable to the DVI IN port on the back of your monitor.
RGB IN port
Connect the D-sub cable to the 15-pin, RGB IN port on the back of your monitor.
Kensington Lock
The 
Kensington 

Lock is a device used to physically fix the system when using it in
a public place. The locking device has to be purchased separately. The appearance
and locking method may differ from the illustration depending on the manufacturer.
Refer to the manual provided with the Kensington Lock for proper use. The locking
device has to be purchased separately.  Note
The location of the Kensington Lock may be different depending on its model.
Using the Anti-Theft Kensington Lock
1. Insert  the 

locking device into the Kensington slot on the Monitor   and turn it
in the locking direction  .
Introduction
12
 
						

							2. Connect the Kensington Lock cable.
3.
Fix the Kensington Lock to a desk or a heavy stationary object.  Note
See Connecting Cables  for further information regarding cable connections.Introduction
13 
						

							Connections
Connecting Cables
 Connect the power cord for your monitor to the power port on the back of the monitor.
Plug the power cord for the monitor into a nearby outlet.  Use a connection appropriate for your computer.
 Using the D-sub (Analog) connector on the video card.
• Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. [RGB IN]
 Using the DVI (Digital) connector on the video card.
• Connect the DVI Cable to the DVI IN Port on the back of your Monitor. [DVI IN]
 Connected to a Macintosh.
• Connect the monitor to the Macintosh computer using the D-sub connection cable.  Note
If the monitor and the computer are connected, you can turn them on and use them. 14 
						

							Using the Stand
Monitor Assembly
Monitor and Bottom
Folding the base  Note
You can tilt the monitor upwards at an angle of -1° to 21°. Connections
15 
						

							Using the Software
Monitor Driver
 Note
When prompted by the operating system for the monitor driver, insert the CD-ROM
included  with 
this monitor. Driver installation is slightly different from one operating
system  to  another.  Follow  the  directions  appropriate  for  the  operating  system  you
have.
Prepare  a  blank  disk  and  download  the  driver  program  file  at  the  Internet  web  site
shown here.
Internet web site :
http://www.samsung.com/ (Worldwide) Installing the Monitor Driver (Automatic)
1.Insert CD into the CD-ROM drive.
2.

Click "Windows".
3. Choose your monitor model in the model list, then click the "OK" button. 4. If 
you can see following message window, then click the "Continue Anyway" button. Then click
"OK" button (Microsoft ®
 Windows ®
 XP/2000 Operating System). 16
 
						

							 Note
This  monitor 
driver is under certifying MS logo, and this installation doesn't damage your system.
The certified driver will be posted on Samsung Monitor homepage.
http://www.samsung.com/
Installing the Monitor Driver (Manual) Microsoft®
 Windows Vista™‚ Operating System
1. Insert your Manual CD into your CD-ROM drive.
2. Click  (Start) and "Control Panel". Then, double-click on "Appearance and Personalization".
3. Click "Personalization" and then "Display Settings".
4. Click "Advanced Settings...".
 
5. Click  "Properties"  in  the  "Monitor"  tab.  If  the  "Properties"  button  is  deactivated,  it  means  the
configuration for your monitor is completed. The monitor can be used as is.
If 

the message "Windows needs..." is displayed, as shown in the figure below, click "Continue". Using the Software
17
 
						

							 Note
This  monitor 
driver is under certifying MS logo, and this installation doesn't damage your system.
The certified driver will be posted on Samsung Monitor homepage.
6. Click "Update Driver..." in the "Driver" tab. 7. Check 
the "Browse my computer for driver software" checkbox and click "Let me pick from a
list of device drivers on my computer". 8. Click 
"Have Disk...” and select the folder (for example, D:\Drive) where the driver setup file is
located, and click "OK". Using the Software
18
 
						

							9. Select 
the model that matches your monitor from the list of monitor models on the screen, and
click "Next".  
10. Click "Close" → "Close" → "OK" → "OK" on the following screens displayed in sequence. Microsoft
®
 Windows ®
 XP Operating System Using the Software
19