Samsung Syncmaster S19a450bw User Manual

							Using the product3-15
3-15 Standard Signal Mode Table
 This product delivers the best picture quality when viewed under the optimal resolution setting. The optimal resolution is 
dependent on the screen size.
Therefore, the visual quality will be degraded if the optimal resolution is not set for the panel size. It is recommended setti ng 
the resolution to the optimal resolution of the product.
 
If the signal from the PC is one of the following standard signal  modes, the screen is set automatically. However, if the signal from 
the PC is not one of the following signal modes, a blank scree n may be displayed or only the Power LED may be turned on. 
Therefore, configure it as follows referring to the User Manual of the graphics card.
 
 
						

							3-15Using the product
S24A450S
Horizontal Frequency
The time taken to scan one line from the left-most position to the right-most position on the screen is called the horizontal cycle 
and the reciprocal of the hori zontal cycle is called the horizon tal frequency. The horizontal frequency is represented in kHz.
Vertical Frequency
A panel must display the same picture on  the screen tens of times every second so that humans can see the picture. This 
frequency is called the vertical frequency. The vertical frequency is represented in Hz.
DISPLAY MODEHORIZONTAL 
FREQUENCY (KHZ)VERTICAL 
FREQUENCY  (HZ)PIXEL CLOCK (MHZ)SYNC POLARITY (H/ V)
IBM, 720 x 400 31.46970.08728.322 -/+
MAC, 640 x 480 35.00066.66730.240 -/-
MAC, 832 x 624 49.72674.55157.284 -/-
MAC, 1152 x 870 68.68175.062100.000 -/-
VESA, 640 x 480 31.46959.94025.175 -/-
VESA, 640 x 480 37.86172.80931.500 -/-
VESA, 640 x 480 37.50075.00031.500 -/-
VESA, 800 x 600 35.156 56.250 36.000 +/+
VESA, 800 x 600 37.879 60.317 40.000 +/+
VESA, 800 x 600 48.077 72.188 50.000 +/+
VESA, 800 x 600 46.875 75.000 49.500 +/+
VESA, 1024 x 768 48.36360.00465.000 -/-
VESA, 1024 x 768 56.47670.06975.000 -/-
VESA, 1024 x 768 60.023 75.029 78.750 +/+
VESA, 1152 x 864 67.500 75.000 108.000 +/+
VESA, 1280 x 800 49.70259.81083.500 -/+
VESA, 1280 x 960 60.000 60.000 108.000 +/+
VESA, 1280 x 1024 63.981 60.020 108.000 +/+
VESA, 1280 x 1024 79.976 75.025 135.000 +/+
VESA, 1440 x 900 55.935 59.887 106.500 -/+
VESA, 1440 x 900 70.635 74.984 136.750 -/+
VESA, 1600 x 1200 75.000 60.000 162.000 +/+
VESA, 1680 x 1050 65.290 59.954 146.250 -/+
VESA, 1920 x 1080 67.500 60.000 148.500 +/+
 
						

							Using the product3-16
3-16 Standard Signal Mode Table
 This product delivers the best picture quality when viewed under the optimal resolution setting. The optimal resolution is 
dependent on the screen size.
Therefore, the visual quality will be degraded if the optimal resolution is not set for the panel size. It is recommended setti ng 
the resolution to the optimal resolution of the product.
 
If the signal from the PC is one of the following standard signal  modes, the screen is set automatically. However, if the signal from 
the PC is not one of the following signal modes, a blank scree n may be displayed or only the Power LED may be turned on. 
Therefore, configure it as follows referring to the User Manual of the graphics card.
 
 
						

							3-16Using the product
S24A450SW
Horizontal Frequency
The time taken to scan one line from the left-most position to the right-most position on the screen is called the horizontal cycle 
and the reciprocal of the hori zontal cycle is called the horizon tal frequency. The horizontal frequency is represented in kHz.
Vertical Frequency
A panel must display the same picture on  the screen tens of times every second so that humans can see the picture. This 
frequency is called the vertical frequency. The vertical frequency is represented in Hz.
DISPLAY MODEHORIZONTAL 
FREQUENCY (KHZ)VERTICAL 
FREQUENCY  (HZ)PIXEL CLOCK (MHZ)SYNC POLARITY (H/ V)
IBM, 720 x 400 31.46970.08728.322 -/+
MAC, 640 x 480 35.00066.66730.240 -/-
MAC, 832 x 624 49.72674.55157.284 -/-
MAC, 1152 x 870 68.68175.062100.000 -/-
VESA, 640 x 480 31.46959.94025.175 -/-
VESA, 640 x 480 37.86172.80931.500 -/-
VESA, 640 x 480 37.50075.00031.500 -/-
VESA, 800 x 600 35.156 56.250 36.000 +/+
VESA, 800 x 600 37.879 60.317 40.000 +/+
VESA, 800 x 600 48.077 72.188 50.000 +/+
VESA, 800 x 600 46.875 75.000 49.500 +/+
VESA, 1024 x 768 48.36360.00465.000 -/-
VESA, 1024 x 768 56.47670.06975.000 -/-
VESA, 1024 x 768 60.023 75.029 78.750 +/+
VESA, 1152 x 864 67.500 75.000 108.000 +/+
VESA, 1280 x 800 49.70259.81083.500 -/+
VESA, 1280 x 960 60.000 60.000 108.000 +/+
VESA, 1280 x 1024 63.981 60.020 108.000 +/+
VESA, 1280 x 1024 79.976 75.025 135.000 +/+
VESA, 1440 x 900 55.935 59.887 106.500 -/+
VESA, 1440 x 900 70.635 74.984 136.750 -/+
VESA, 1600 x 1200 75.000 60.000 162.000 +/+
VESA, 1680 x 1050 65.290 59.954 146.250 -/+
VESA, 1920 x 1200 74.556 59.885 193.250 -/+
 
						

							Using the product3-17
3-17 Installing the Device Driver
 If you install the device driver, you can set up the appropriate resolution and frequency for the product. The device driver is 
included on the CD-ROM supplied with the product. If the supplied dr ive file is corrupted, please visit a service center or 
Samsung Electronics website(http://www.sa msung.com/), and download the driver.
 
1.Insert the driver installation  CD-ROM into the CD-ROM drive.
2. Click on Windows Driver.
3. Complete the remaining installation steps according to the instructions displayed on the screen.
4. Select the model of your pr oduct from the model list.
5. Check if the appropriate resolution and screen refresh rate are displayed in the Control Panel settings. For more information, 
refer to the document about the Windows operating system.
 
						

							3-18Using the product
3-18 Product Operating Buttons
Product Operating Buttons
 • Press one of the buttons on the monitor. OSD Guide will appear on the screen.
• If you press a button on the front of the monitor, an OSD Gu ide will display showing the function of the button before the 
menu for the pressed button appears.
• To go to the menu, press the button on the front of the monitor again.
• OSD Guide may vary according to functions and models. Please refer to actual product.
 
ICONDESCRIPTION
MENU Press this button to view the On Screen Display (OSD).
This button is also used to exit the OS D or to return to a higher-level OSD menu
* OSD Adjustment Lock
This function locks the OSD in order to maintain  the current settings or to prevent the settings 
from being changed by another person
On: If you press and hold the MENU button dow n for 5 seconds, the OSD Adjustment Lock 
function is activated.
Off: If you press and hold the MENU button dow n for 5 seconds again, the OSD Adjustment 
Lock function is disabled.
 Even if the OSD Adjustment Lo ck function is activated, users can adjust the brightness 
and contrast and can set up the adjust ment function assigned to the [ ].
 
Users can set the  to one of  the following functions. If the user presses the 
Customized Key [ ] after setting it, th e configured function will be performed
• < Angle> - < Bright> -  - 
 You can set the function of the Customiz ed Key by selecting  -> 
 in the OSD.
 
▲ /▼ Use these buttons to navigate the menu  or to adjust a value in the OSD. 
 
						

							Using the product3-18
Use this button to control the brightness of the screen. 
 When OSD is not on the screen, push the button to adjust volume.
Applicable to the models that have speakers only.
 
Use this button to select a function.
If you press the [  ] button when there is no  OSD, the input signal (Analog/Digital) is 
switched. When the input signal is switched  by pressing [ ] button or the product is 
turned on, a message displaying the selected  input signal appears at the top left of the 
screen.
 This function is not available for products with an Analog interface only. 
AUTO Press [AUTO] button to adjust the screen settings automatically
 This function is only available in Analog mode. 
If the resolution settings are changed in the  Display Properties, the AUTO adjustment func-
tion is performed.
Press this button to turn the product on or off
Power LED
This LED is turned on when the product works normally. 
 For more information on the power-saving function, refer to the power saving function 
in More Information. When not using the product for a long time, unplugging the power 
cord is recommended to minimize power consumption.
 
ICONDESCRIPTION
 
						

							3-19Using the product
3-19 Using the Screen Adjustment Menu (OSD: On Screen Display)
The Screen Adjustment Menu (OSD: On Screen Display) Structure
 Monitor functions may vary according to models. Please refer to actual product. 
 PICTURE
Top MenusSub Menus
 PICTUREBrightness Contrast Sharpness
Bright Angle
Coarse Fine
 COLOR
ColorRed Green Blue Color Tone
Gamma    
 SIZE & POSI-
TION H-Position V-Position Image Size Menu H-Position Menu V-Position
 
SETUP&RESET Reset Language Eco Saving Off Timer On/Off Off Timer Setting
PC/AV Mode Key Repeat Time Customized Key Auto Source Display Time
Menu Transpar-
ency
 INFORMA-
TION
MenuDescription
Brightness Controls the screen brightness.
 
• This menu is unavailable when < Bright> is set to  mode.
• This menu is unavailable when  is set.
 
ContrastControls the contrast of the pi
ctures displayed on the screen
 
• This menu is unavailable when < Bright> is set to  or  
mode.
• This menu is unavailable when < Color> is set to  mode or  mode.
 
 
						

							Using the product3-19
SharpnessControls the clarity of details of pictures displayed on the screen
 
• This menu is unavailable when < Bright> is set to  or  
mode.
• This menu is unavailable when < Color> is set to  mode or  mode.
 
Bright Provides preset picture settings optimized for vari
ous user environments such as editing a document, 
surfing the Internet, playing games,or movies and so on.
• 
If the preset picture modes are not sufficient, users can co nfigure the  and  
directly using this mode.
• 
 This mode provides the picture setting appropria te for editing a document and surfing the Internet 
(text + picture).
•
This mode provides the picture sett ing appropriate for playing games that include lots of graphics and 
that require a fast screen refresh rate.
• 
This mode provides brightness and sharpness se ttings similar to those of a TV for the best 
entertainment environment (movie, DVD, etc.).
• 
Controls the picture contrast aut omatically so that bright and dark pictures are balanced overall.
 This menu is unavailable when < Angle> or  is set. 
MenuDescription
 
						

							3-19Using the product
AngleThis feature allows you to see optimal screen quality according to your viewing position.
When viewing the screen at an angle from below, abov
e or the side of the monitor, by setting the 
appropriate mode for each position you can obtain a similar picture quality as viewing the screen 
directly from the front.
 Set to  when viewing directly in front of the screen. 
•    - Select when viewing from the front position.
•    - Select when viewing from a slightly lower position.
•    - Select when viewing from the lower position.
•    -Select when viewing from the upper position.
•    - Select when viewing from the left or right position.
•   - Select when two or more persons view among  , ,  position at the same 
time.
•   -When  is selected, settings  for  is applied by default. 
Users can set suitable picture quality as needed.
 
• This menu is unavailable when < Bright> is set to  or  
mode.
• This menu is unavailable when < Color> is set.
 
Coarse Removes vertical noise lines (l
ine pattern) from the screen.
The location of the screen may be changed after the  adjustment. In this case, move the screen so 
that the screen is displayed at  the center of the display panel using the  menu.
 This function is only available in Analog mode. 
FineRemoves horizontal noise lines 
(line pattern) from the screen.
If you cannot remove the noise completely with  the  function, adjust the  and then 
use the  function again.
 This function is only available in Analog mode. 
MenuDescription