Samsung Syncmaster S19a450br User Manual

							Major Safety Precautions1-4
Maintaining the Correct Posture when Using this Product 
Be careful that adaptor should not be in contact 
with water and therefore not be wet. 
• This may cause a malfunction, electric 
shock or fire. Do not use adaptor by the 
waterside or outside particularly when it 
rains or snows. Be  careful that adaptor 
should not be wet while cleaning floor with 
water.Watching the product from too close a distance 
continuously may damage your eyesight.
Avoid using a humidifier or cooker near the 
product.
• Otherwise, it may result  in electric shock or 
fire.It is important to give yo ur eyes some rest (5 
minutes every hour) when viewing the product 
screen for long periods of time.
• This will alleviate any eye strain.
Since the display panel is hot after using it for a 
long time, do not touch the product.Keep small accessories away from the children.
Take care when adjusting the angle of the 
product or the height of the stand.
• If your hand or finger is caught, you may be  injured.
• If the product is tilt ed excessively, the 
product may fall and this may result in 
injury.Avoid placing a heavy object over the product.
• Otherwise, it may result in a problem with  the product or injury.
Maintain the correct posture  when using this product.
• Straighten your back.
• Keep a distance of 45~50 cm from your ey es to the screen. Look down at the screen and 
face the screen forwards.
• Adjust the angle of the product so t hat light is not reflected onto the screen.
• Keep your elbow at a right angle and keep  your arm level with the back of your hand.
• Keep your elbow at a right angle.
• Place your heels flat on the ground while k eeping your knees at an angle of 90 degrees or 
higher and maintain the position of your arm so that your arm is below your heart.
 
						

							2-1Installing the Product
2 Installing the Product
2-1 Package Contents
 • Unpack the product and check if all of the following contents have been included.
• Store the packaging box in case you need to move the Product at a later stage.
 
Monitor
 The cables provided may vary depending on the product you purchase. 
Contents
Installation Manual Product Warranty
(Not available in all locations)  User ManualDC-Adapter
Power Cord                                     Stand   
OPTION
DVI Cable D-Sub Cable  USB CableStereo Cable
 
						

							Installing the Product2-2
2-2 Installing the Stand
 Before assembling the product, place the product down on a flat and stable surface so that the screen is facing downwards. 
Place a soft cloth over the table to protect the product and place the product onto the 
cloth so that the front of the product is facing downwards.
Rotate the stand-body following the arrow as shown
Check if the stand-body had rotated to the right location as shown.
Push the stand-base into the stand-body follo wing the arrow as shown,when you heard a 
sound click then you had fixed the stand-base rightly.
Install the adapter into the recess on the back cover of the monitor as shown.
Stand the set on base and remove the pin.
 
						

							2-2Installing the Product
 Disassembly is in the reverse order of the assembly. 
Push the adapter forward and then rotate following the arrow to get it out.
Hold the base and thumbs press the stand body then pull out the base following the 
arrow.
- Caution
Avoid lifting the product holding only the stand.
When pivot the monitor from horizontal to ve rtical,tilt the monitor backward to maxium 
first.
  . Stand Stopper
 
						

							Installing the Product2-3
2-3 Installing the Stand for the Wall Mount
This product provides a stand mount of 100 mm x 100 mm / 100 mm  x 200 mm(3.9 x 3.9 inches / 3.9 x 7.9 inches) that complies 
with the VESA specifications.
HAS stand
1. Turn the product off and unplug the power cord from the wall outlet.
2. Place a soft cloth or cushion on a flat surface to protect the panel and place the product down  on the cloth so that the front of 
the product faces downwards.
3. Separate the stand.
4. Align the groove of the part of the product that is to be conne cted to the stand with the groove in the stand (desk-top stand, 
wall mount stand or another stand) and fi rmly fix the stand by fastening the screw.
 • If you use a screw that is longer than the standard specifications, the inside of the product may be damaged.
• For wall mounts that are not compatible with the standard  VESA specifications, the length of the screw may differ 
depending on the corresponding specifications.
• Do not use screws that are incompat ible with the standard VESA specifications and do not assemble them using 
excessive force.
• This may result in damage to the product or injury due to the product falling.
• The company shall not be held liable for any damage or injury.
• The company shall not be held liable for any damage to the  product or injury caused by using a stand that is not 
compatible with the specified  specifications or due to an installation  not performed by an authorized installation 
engineer. 
• When installing the product using a wall mount, purchase a  wall mount that provides at least 10 cm of space from 
the wall.
• The company shall not be held liable for any problems c aused by using a stand that is not compatible with the 
specified specifications.
• Use the wall mount according to the international specifications.
 
 Stand Mount
 Stand (Optional)
 
						

							2-4Installing the Product
2-4 Connecting with a PC
 The connecting part may differ depending on the product model. 
1.Connect the product to a PC depending  on the video output supported by the PC.
•  When the graphics card provides D-Sub 
	Analog 

output
• Connect the [RGB IN] port of the product to t he [D-Sub] port of the PC with the D-Sub cable.
•  When the graphics card provides DVI 	Digital 
 output
•  Connect the [DVI IN] port of the product to the [DVI] port of the PC with the DVI cable.
 The [DVI IN] terminal is supplied for the digital (DVI)-dedicated models only. 
2. Connect the power adapter to [DC 14V] on the rear of the produ ct. Connect the power cord to the adapter and wall socket.
(The input voltage is switched automatically.)
POWER ON [  │ ] / OFF [ O ]
 
						

							Installing the Product2-4
Switches the Power On/Off.
 When the product is connected to a PC, you can turn the product on and use it. 
3.Connect the [AUDIO IN] port on the rear side of the monitor to the sound card of the PC.
Connect your headphones to the Headphone connection terminal.
 Applicable to the models that have speakers only.
 
 
						

							2-5Installing the Product
2-5 Fixing cables
Cables can be fixed as shown.
 
						

							Installing the Product2-6
2-6 Speaker
You can hear sound by connecting the soundcard of your PC to the monitor.
 Applicable to the models that have speakers only. 
 
						

							2-7Installing the Product
2-7 Kensington Lock
A Kensington Lock is an anti-theft device that enables users to lock the product so  that they can safely use it in public locations. 
Since the shape and usage of the locking device may differ depending on the model and the manufacturer, for more information, 
refer to the User Manual supplied with the locking device for more information.
 You must purchase the Kensington Lock separately. 
To lock the product, follow these steps: 
1. Wrap the Kensington lock cable around a large,  stationary object such as a desk or chair.
2. Slide the end of the cable with the lock attached through the looped end of the Kensington lock cable.
3. Insert the locking device into the  Kensington slot on the Monitor( ).
4. Lock the lock( ).
 • These are general instructions. For exact instructions, see the User Manual supplied with the locking device.
•
You can purchase the locking device from an electronics store, an online shop, or our service center.