Samsung Syncmaster P2770hd User Manual

Using the Product3-3
Installing Batteries in the Remote Control
1.Lift the cover at the back of the remote control upward as shown in the figure.
2.Install two AAA size batteries.
 Make sure to match the +and - ends of the batteries with the diagram inside the compartment. 
3.Close the cover.
 Remove the batteries and store them in a cool, dry place if you wont be using the remote control for a long time.
If the remote control doesnt work, check the following :
• Is the TV power on?
• Are the plus and...

3-4Using the Product
3-4 Using the Screen Adjustment Menu (OSD: On Screen Display)
The Screen Adjustment Menu (OSD: On Screen Display) Structure
Available Modes
The icons below represent the input signals that are displayed when selecting an item in the .
TOP MENUSSUB MENUS
Picture
[PC / DVI]MagicBright Contrast Brightness Sharpness Auto Adjustment 
Screen Picture Options Picture Reset
Picture
[TV / AV / Component / 
HDMI]Mode Backlight Contrast  Brightness Sharpness
Color Tint (G/R) Advanced Set-
tings...

Using the Product3-4
Picture [PC / DVI ]
 The default setting may be different depending on the selected Input Mode (input signal source selected in External Input 
List) and the selected resolution
 
MENUDESCRIPTION
MagicBright   is a feature providing an optimum viewing environment depending on the contents of 
the image you are watching. Currently five different modes are available: , , 
,  and . Each mode has its own pre-configured brightness 
value. 
•
 High Brightness
 For watching motion pictures...

3-4Using the Product
Picture [ TV / AV / Component / HDMI ] 
Screen • 
Removes noise such as vertical stripes.
 adjustment may move the screen image area. You may relocate it to the center using 
the horizontal control menu
•
Removes noise such as horizontal stripes.
If the noise persists even after  tuning, repeat it after adjusting the frequency (.)
• 
Adjusts the screen location horizontally and vertically.
• 
Image parameters are replaced with the factory default values.
 Available in  Mode Only...

Using the Product3-4
MENUDESCRIPTION
Mode The Monitor has three automatic picture settings (, , and ) that are 
preset at the factory.
You can activate either , , or .
• 
Selects the picture for high-definition in a bright room.
• 
Selects the picture for optimum display in a normal environment.
•
Selects the picture for viewing movies in a dark room.
 Press the [TOOLS] button to display the Tools menu. You can also set the  by 
selecting →.
Backlight / Contrast / 
Brightness / Sharp-
ness / Color / Tint...

3-4Using the Product
Picture Options • 
The tone of the color can be changed.
•  -  -  - 
 •  or  is only activated when the picture mode is .
• Settings can be adjusted and stored for each external device you have connected to an 
input of the TV.
 
• 
 You can switch the Size.
The direct button on the remote control is [P.SIZE] button. 
•  - Sets the picture to 16:9 wide mode. 
•  - Magnifies the size of the picture on the screen. 
•  - Magnifies the size of the picture more than . 
•  - Enlarges the...

Using the Product3-4
Sound
MENUDESCRIPTION
Mode • 
 Choose Standard for the standard factory settings.
• 
 Choose Music when watching music videos or concerts.
•
 Choose Movie when viewing movies.
• 
 Emphasizes voice over other sounds.
• 
 Choose Custom if you want to adjust the settings according to personal preference .
 Press the [TOOLS] button to display the Tools menu. You can also set the  by 
selecting →.
Equalizer  You can adjust the left and right sound balance and equalizer settings as...

3-4Using the Product
Channel
Multi-Track Sound  • 
 Choose for channels that are broadcasting in mono or if you are having difficulty receiving a stereo 
signal.
• 
 Choose for channels that are broadcasting in stereo.
• 
 Choose to listen to the Separate Audio Program, which is usually a foreign-language translation.
 Available in Analog  Mode Only 
Auto Volume Reduces the differences in volume level among channels.
•  - 
Speaker Select When you watch TV with it connecting to a Home theater, turn the TV...

Using the Product3-4
MENUDESCRIPTION
Antenna You can select antenna or cable TV.
If [ANT IN] connected, select the antenna input you want. If the antenna input is not selected prop-
erly, noise may appear on the screen.
•  - 
Auto Program  The TV automatically cycles through all of the available channels and stores them in memory.
In rare cases,  may miss a few channels due to weak signals and the channels may 
not be added to the channel memory.
•  -  - 
Clear Scrambled 
Channel The Clear Scrambled...

3-4Using the Product
Channel List Using this menu, you can add / delete or set favorite channels and use the program guide for digital 
broadcasts.
You can select these options by simply pressing the [CH LIST] button on the remote control.
•  - Shows all currently available channels.
•  - Shows all added channels.
•  - Shows all favorite channels.
 Press the [TOOLS] button to display the  menu. You can also set the add to (or delete 
from) Favorites by selecting → (or ).
 To select the favorite channels...