Samsung Syncmaster P2450h User Manual

							Installing the Product2-1
2 Installing the Product
2-1 Package Contents
 • Unpack the product and check if all of the following contents have been included.
• Store the packaging box in case you need to move the Product at a later stage.
 
Monitor
 The cleaning cloth is supplied with black high-glossy models only. 
CONTENTS
Installation Manual Product Warranty
(Not available in all locations)User Manual D-Sub Cable
Power Cord Cleaning Cloth Cable Arrangement Link Stand Connector
Stand
OPTIONAL PARTS
DVI Cable HDMI Cable
 
						

							2-2Installing the Product
2-2 Installing the Stand
 Before assembling the product, place the product down on a flat and stable surface so that the screen is facing downwards. 
Insert the Stand Connector into the Stand in the direction shown by the figure.
Check if the Stand Connector is firmly connected.
Turn the connecting screw at the bottom of the stand fully so that it is completely fixed.
Place a soft cloth over the table to protect the product and place the product onto the 
cloth so that the front of the product is facing downwards.
 
						

							Installing the Product2-2
Hold the main body of the product with your hand as shown by the figure.
Push the assembled stand into the main body in the direction of the arrow as shown in 
the figure.
- Caution
Do not lift the product holding only the stand
 
						

							2-3Installing the Product
2-3 Removing the Stand
 Before removing the stand, place the product down on a flat and stable surface so that the screen faces downwards. 
Place a soft cloth over the table to protect the product and place the product onto the 
cloth so that the front of the product faces downwards.
Hold the main body of the product with your hand as shown by the figure. 
Pull the stand in the direction of the arrow as shown in the figure to separate it.
Turn the connecting screw at the bottom of the stand to separate it.
Take the Stand Connector out of the Stand by pulling it in the direction of the arrow as 
shown in the figure.
 
						

							Installing the Product2-4
2-4 Installing the Stand for the Wall Mount
This product provides a stand mount of 100 mm x 100 mm that complies with the VESA specifications.
1.Turn the product off and unplug the power cord from the wall outlet.
2.Place a soft cloth or cushion on a flat surface to protect the panel and place the product down on the cloth so that the front of 
the product faces downwards.
3.Separate the stand.
4.Align the groove of the part of the product that is to be connected to the stand with the groove in the stand (desk-top stand, 
wall mount stand or another stand) and firmly fix the stand by fastening the screw.
 •If you use a screw that is longer than the standard specifications, the inside of the product may be damaged.
•For wall mounts that are not compatible with the standard VESA specifications, the length of the screw may differ 
depending on the corresponding specifications.
•Do not use screws that are incompatible with the standard VESA specifications and do not assemble them using excessive 
force.
This may result in damage to the product or injury due to the product falling.
The company shall not be held liable for any damage or injury.
•The company shall not be held liable for any damage to the product or injury caused by using a stand that is not compatible 
with the specified specifications or due to an installation not performed by an authorized installation engineer. 
•When installing the product using a wall mount, purchase a wall mount that provides at least 10 cm of space from the wall.
•The company shall not be held liable for any problems caused by using a stand that is not compatible with the specified 
specifications.
•Use the wall mount according to the international specifications.
 
A. Stand Mount
B. Stand (Optional)
 
						

							2-5Installing the Product
2-5 Connecting with a PC
 The connecting part may differ depending on the product model. 
1.Connect the product to a PC depending on the video output supported by the PC.
• When the graphics card provides D-Sub (analog) output
• Connect the [RGB IN] port of the product to the [D-Sub] port of the PC with the D-Sub cable.
• When the graphics card provides DVI (digital) output
• Connect the [DVI IN] port of the product to the DVI port of the PC with the DVI cable.
2.Connect one end of the power cord to the [POWER] port of the product and connect the other end of the power cord to the 
220V or 110V wall outlet.
(The input voltage is switched automatically.)
 When the product is connected to a PC, you can turn the product on and use it.
When both the DVI () and D-Sub () cables are connected, you can select the input signal 
						

							Installing the Product2-5
Digital> by pressing the   button. 
 
						

							2-6Installing the Product
2-6 Connecting a HDMI cable 
Connect the HDMI output port of your digital output device to the [HDMI] port of the product using the HDMI cable.
Connect a speaker to the [AUDIO OUT] port of the product.
 This product wont make any sound when only the HDMI cable is connected without a speaker connected.
When all the connections are complete, you can turn on and use the product and your DVD player (or digital output device).
 
 Press the [ ] button and select  as an input signal.
 
						

							Installing the Product2-7
2-7 Connecting to an Amplifier
Connect the [DIGITAL AUDIO OUT] terminal of your monitor to the optical input of your amplifier using an optical cable.
 • If no sound is emitted from the monitor, you need to use an amplifier.
• For information on how to connect a speaker and amplifier, refer to the respective user manuals provided by their 
manufacturers.
 
 
						

							2-8Installing the Product
2-8 Kensington Lock
Kensington Lock
A Kensington Lock is an anti-theft device that enables users to lock the product so that they can safely use it in public locations. 
Since the shape and usage of the locking device may differ depending on the model and the manufacturer, for more information, 
refer to the User Manual supplied with the locking device. You have to purchase an additional locking device.
Locking the product
1.Insert the locking part of the locking device into the hole of the Kensington lock of the product (  ) and turn it in the locking 
direction ( ).
2.Connect the Kensington lock cable.
3.Tie the Kensington lock cable to a desk or heavy object.
 You can purchase the locking device from an electronics store, an online shop, or our service center.