Samsung Syncmaster B2440m User Manual

							Using the product3-37
Vertical Frequency
A panel must display the same picture on the screen tens of times every second so that humans can see the picture. This 
frequency is called the vertical frequency. The vertical frequency is represented in Hz.
 
						

							3-38Using the product
3-38 Standard Signal Mode Table
 The LCD monitor has one optimal resolution for the best visual quality depending on the screen size due to the inherent 
characteristics of the panel, unlike for a CDT monitor.
Therefore, the visual quality will be degraded if the optimal resolution is not set for the panel size. It is recommended setting 
the resolution to the optimal resolution of the product.
 
If the signal from the PC is one of the following standard signal modes, the screen is set automatically. However, if the signal from 
the PC is not one of the following signal modes, a blank screen may be displayed or only the Power LED may be turned on. 
Therefore, configure it as follows referring to the User Manual of the graphics card.
E2420NL/E2420NLX
Horizontal Frequency
The time taken to scan one line from the left-most position to the right-most position on the screen is called the horizontal cycle 
and the reciprocal of the horizontal cycle is called the horizontal frequency. The horizontal frequency is represented in kHz.
Vertical Frequency
A panel must display the same picture on the screen tens of times every second so that humans can see the picture. This 
frequency is called the vertical frequency. The vertical frequency is represented in Hz.
DISPLAY MODEHORIZONTAL 
FREQUENCY (KHZ)VERTICAL 
FREQUENCY (HZ)PIXEL CLOCK (MHZ)SYNC POLARITY (H/
V)
IBM, 720 x 400 31.469 70.087 28.322 -/+
MAC, 640 x 480 35.000 66.667 30.240 -/-
MAC, 832 x 624 49.726 74.551 57.284 -/-
MAC, 1152 x 870 68.681 75.062 100.000 -/-
VESA, 640 x 480 31.469 59.940 25.175 -/-
VESA, 640 x 480 37.861 72.809 31.500 -/-
VESA, 640 x 480 37.500 75.000 31.500 -/-
VESA, 800 x 600 35.156 56.250 36.000 +/+
VESA, 800 x 600 37.879 60.317 40.000 +/+
VESA, 800 x 600 48.077 72.188 50.000 +/+
VESA, 800 x 600 46.875 75.000 49.500 +/+
VESA, 1024 x 768 48.363 60.004 65.000 -/-
VESA, 1024 x 768 56.476 70.069 75.000 -/-
VESA, 1024 x 768 60.023 75.029 78.750 +/+
VESA,1152 X 864 67.500 75.000 108.000 +/+
VESA,1280 X 800 49.702 59.810 83.500 -/+
VESA,1280 X 960 60.000 60.000 108.000 +/+ 
VESA, 1280 X 1024 63.981 60.020 108.000 +/+
VESA, 1280 X 1024 79.976 75.025 135.000 +/+
VESA,1440 X 900 55.935 59.887 106.500 -/+
VESA,1440 X 900 70.635 74.984 136.750 -/+
VESA,1600 X 1200 75.000 60.000 162.000 +/+
VESA,1680 X 1050 65.290 59.954 146.250 -/+
VESA,1920 X 1080 67.500 60.000 148.500 +/+
 
						

							Using the product3-39
3-39 Standard Signal Mode Table
 The LCD monitor has one optimal resolution for the best visual quality depending on the screen size due to the inherent 
characteristics of the panel, unlike for a CDT monitor.
Therefore, the visual quality will be degraded if the optimal resolution is not set for the panel size. It is recommended setting 
the resolution to the optimal resolution of the product.
 
If the signal from the PC is one of the following standard signal modes, the screen is set automatically. However, if the signal from 
the PC is not one of the following signal modes, a blank screen may be displayed or only the Power LED may be turned on. 
Therefore, configure it as follows referring to the User Manual of the graphics card.
E2420L/E2420LX
Horizontal Frequency
The time taken to scan one line from the left-most position to the right-most position on the screen is called the horizontal cycle 
and the reciprocal of the horizontal cycle is called the horizontal frequency. The horizontal frequency is represented in kHz.
Vertical Frequency
A panel must display the same picture on the screen tens of times every second so that humans can see the picture. This 
frequency is called the vertical frequency. The vertical frequency is represented in Hz.
DISPLAY MODEHORIZONTAL 
FREQUENCY (KHZ)VERTICAL 
FREQUENCY (HZ)PIXEL CLOCK (MHZ)SYNC POLARITY (H/
V)
IBM, 720 x 400 31.469 70.087 28.322 -/+
MAC, 640 x 480 35.000 66.667 30.240 -/-
MAC, 832 x 624 49.726 74.551 57.284 -/-
MAC, 1152 x 870 68.681 75.062 100.000 -/-
VESA, 640 x 480 31.469 59.940 25.175 -/-
VESA, 640 x 480 37.861 72.809 31.500 -/-
VESA, 640 x 480 37.500 75.000 31.500 -/-
VESA, 800 x 600 35.156 56.250 36.000 +/+
VESA, 800 x 600 37.879 60.317 40.000 +/+
VESA, 800 x 600 48.077 72.188 50.000 +/+
VESA, 800 x 600 46.875 75.000 49.500 +/+
VESA, 1024 x 768 48.363 60.004 65.000 -/-
VESA, 1024 x 768 56.476 70.069 75.000 -/-
VESA, 1024 x 768 60.023 75.029 78.750 +/+
VESA,1152 X 864 67.500 75.000 108.000 +/+
VESA,1280 X 800 49.702 59.810 83.500 -/+
VESA,1280 X 960 60.000 60.000 108.000 +/+ 
VESA, 1280 X 1024 63.981 60.020 108.000 +/+
VESA, 1280 X 1024 79.976 75.025 135.000 +/+
VESA,1440 X 900 55.935 59.887 106.500 -/+
VESA,1440 X 900 70.635 74.984 136.750 -/+
VESA,1600 X 1200 75.000 60.000 162.000 +/+
VESA,1680 X 1050 65.290 59.954 146.250 -/+
VESA,1920 X 1080 67.500 60.000 148.500 +/+
 
						

							3-40Using the product
3-40 Standard Signal Mode Table
 The LCD monitor has one optimal resolution for the best visual quality depending on the screen size due to the inherent 
characteristics of the panel, unlike for a CDT monitor.
Therefore, the visual quality will be degraded if the optimal resolution is not set for the panel size. It is recommended setting 
the resolution to the optimal resolution of the product.
 
If the signal from the PC is one of the following standard signal modes, the screen is set automatically. However, if the signal from 
the PC is not one of the following signal modes, a blank screen may be displayed or only the Power LED may be turned on. 
Therefore, configure it as follows referring to the User Manual of the graphics card.
EX1920/EX1920X
Horizontal Frequency
The time taken to scan one line from the left-most position to the right-most position on the screen is called the horizontal cycle 
and the reciprocal of the horizontal cycle is called the horizontal frequency. The horizontal frequency is represented in kHz.
Vertical Frequency
A panel must display the same picture on the screen tens of times every second so that humans can see the picture. This 
frequency is called the vertical frequency. The vertical frequency is represented in Hz.
DISPLAY MODEHORIZONTAL 
FREQUENCY (KHZ)VERTICAL 
FREQUENCY (HZ)PIXEL CLOCK (MHZ)SYNC POLARITY (H/
V)
IBM, 720 x 400 31.469 70.087 28.322 -/+
MAC, 640 x 480 35.000 66.667 30.240 -/-
MAC, 832 x 624 49.726 74.551 57.284 -/-
VESA, 640 x 480 31.469 59.940 25.175 -/-
VESA, 640 x 480 37.861 72.809 31.500 -/-
VESA, 640 x 480 37.500 75.000 31.500 -/-
VESA, 800 x 600 35.156 56.250 36.000 +/+
VESA, 800 x 600 37.879 60.317 40.000 +/+
VESA, 800 x 600 48.077 72.188 50.000 +/+
VESA, 800 x 600 46.875 75.000 49.500 +/+
VESA, 1024 x 768 48.363 60.004 65.000 -/-
VESA, 1024 x 768 56.476 70.069 75.000 -/-
VESA, 1024 x 768 60.023 75.029 78.750 +/+
VESA,1360 x 768 47.712 60.015 85.500 +/+
 
						

							Using the product3-41
3-41 Standard Signal Mode Table
 The LCD monitor has one optimal resolution for the best visual quality depending on the screen size due to the inherent 
characteristics of the panel, unlike for a CDT monitor.
Therefore, the visual quality will be degraded if the optimal resolution is not set for the panel size. It is recommended setting 
the resolution to the optimal resolution of the product.
 
If the signal from the PC is one of the following standard signal modes, the screen is set automatically. However, if the signal from 
the PC is not one of the following signal modes, a blank screen may be displayed or only the Power LED may be turned on. 
Therefore, configure it as follows referring to the User Manual of the graphics card.
EX2020/EX2020X
Horizontal Frequency
The time taken to scan one line from the left-most position to the right-most position on the screen is called the horizontal cycle 
and the reciprocal of the horizontal cycle is called the horizontal frequency. The horizontal frequency is represented in kHz.
Vertical Frequency
A panel must display the same picture on the screen tens of times every second so that humans can see the picture. This 
frequency is called the vertical frequency. The vertical frequency is represented in Hz.
DISPLAY MODEHORIZONTAL 
FREQUENCY (KHZ)VERTICAL 
FREQUENCY (HZ)PIXEL CLOCK (MHZ)SYNC POLARITY (H/
V)
IBM, 720 x 400 31.469 70.087 28.322 -/+
MAC, 640 x 480 35.000 66.667 30.240 -/-
MAC, 832 x 624 49.726 74.551 57.284 -/-
MAC, 1152 x 870 68.681 75.062 100.000 -/-
VESA, 640 x 480 31.469 59.940 25.175 -/-
VESA, 640 x 480 37.861 72.809 31.500 -/-
VESA, 640 x 480 37.500 75.000 31.500 -/-
VESA, 800 x 600 35.156 56.250 36.000 +/+
VESA, 800 x 600 37.879 60.317 40.000 +/+
VESA, 800 x 600 48.077 72.188 50.000 +/+
VESA, 800 x 600 46.875 75.000 49.500 +/+
VESA, 1024 x 768 48.363 60.004 65.000 -/-
VESA, 1024 x 768 56.476 70.069 75.000 -/-
VESA, 1024 x 768 60.023 75.029 78.750 +/+
VESA,1152 X 864 67.500 75.000 108.000 +/+
VESA,1280 X 800 49.702 59.810 83.500 -/+
VESA,1280 X 800 62.795 74.934 106.500 -/+
VESA,1440 X 900 55.935 59.887 106.500 -/+
VESA,1440 X 900 70.635 74.984 136.750 -/+
VESA,1600x 900 60.000 60.000 108.000 +/+
 
						

							3-42Using the product
3-42 Installing the Device Driver
 If you install the device driver, you can set up the appropriate resolution and frequency for the product. The device driver is 
included on the CD-ROM supplied with the product. If the supplied drive file is corrupted, please visit a service center or 
Samsung Electronics website(http://www.samsung.com/), and download the driver.
Related Windows 7 driver can be downloaded from Samsung Electronics website.
 
1.Insert the driver installation CD-ROM into the CD-ROM drive.
2.Click on Windows Driver.
3.Complete the remaining installation steps according to the instructions displayed on the screen.
4.Select the model of your product from the model list.
5.Check if the appropriate resolution and screen refresh rate are displayed in the Control Panel settings. For more information, 
refer to the document about the Windows operating system.
 
						

							Using the product3-43
3-43 Product Operating Buttons
Product Operating Buttons
IconDescription
Press this button to view the On Screen Display (OSD).
This button is also used to exit the OSD or to return to a higher-level OSD menu
* OSD Adjustment Lock
This function locks the OSD in order to maintain the current settings or to prevent the 
settings from being changed by another person
On: If you press and hold the MENU button down for 5 seconds, the OSD Adjustment 
Lock function is activated.
Off: If you press and hold the MENU button down for 5 seconds again, the OSD 
Adjustment Lock function is disabled.
 Even if the OSD Adjustment Lock function is activated, users can adjust the 
brightness and contrast and can set up the adjustment function assigned to the 
[].
 
Users can set the  to one of the following functions. If the user 
presses the  [ ] after setting it, the configured function will be per-
formed
• PC signals :  -  -  - 
• AV signals :  -  -  - 
 You can set the function of the  by selecting 
 ->  in the OSD.
 
▲/▼Use these buttons to navigate the menu or to adjust a value in the OSD. 
Use this button to control the brightness of the screen. 
 
						

							3-43Using the product
Activates a highlighted menu item.
 In the  menu, you can also use this button to sequently switch 
between functions in the  menu as desired. 
 
SOURCEUse this button to select a function
If you press the [SOURCE] button when there is no OSD, the input signal (Analog/Dig-
ital/HDMI) is switched. When the input signal is switched by pressing [SOURCE] but-
ton or the product is turned on, a message displaying the selected input signal appears 
at the top left of the screen.
 • To select Digital mode, you have to connect the product and the PC with the 
DVI cable.
• This function is not available for products with an Analog interface only.
 
AUTOPress [AUTO] button to adjust the screen settings automatically
 This function is only available in Analog mode. 
If the resolution settings are changed in the Display Properties, the AUTO adjustment 
function is performed.
Press this button to turn the product on or off
Power LED
This LED is turned on when the product works normally. 
 For more information on the power-saving function, refer to the power saving 
function in More Information. When not using the product for a long time, 
unplugging the power cord is recommended to minimize power consumption.
 
When OSD is not on the screen, push the button to adjust volume.
IconDescription
 
						

							Using the product3-44
3-44 Using the Screen Adjustment Menu (OSD: On Screen Display)
The Screen Adjustment Menu (OSD: On Screen Display) Structure
 Monitor functions may vary according to models. Please refer to actual product. 
 PICTURE
Top MenusSub Menus
 PICTUREBrightness Contrast Sharpness MagicBright Picture Mode
MagicAngle Coarse Fine HDMI Black Level
 COLORMagicColor Red Green Blue Color Tone
Color Effect Gamma      
 SIZE & POSI-
TIONH-Position V-Position Image Size Menu H-Position Menu V-Position
 
SETUP&RESETReset Language MagicReturn MagicEco Off Timer On/Off
Off Timer Setting Key Repeat TimeCustomized Key Auto Source PC/AV Mode
Display Time Menu Transpar-
ency
 INFORMA-
TION
 
MenuDescription
BrightnessControls the screen brightness. • This menu is unavailable when  is set to  mode.
• This menu is unavailable when  is set.
 
ContrastControls the contrast of the pictures displayed on the screen
 • This menu is unavailable when  is set to  or  
mode.
• This menu is unavailable when  is set to  mode or  mode.
• This menu is unavailable when  is set.
 
 
						

							3-44Using the product
SharpnessControls the clarity of details of pictures displayed on the screen
 • This menu is unavailable when  is set to  or  
mode.
• This menu is unavailable when  is set to  mode or  mode.
• This menu is unavailable when  is set.
 
MagicBrightProvides preset picture settings optimized for various user environments such as editing a document, 
surfing the Internet, playing games,or movies and so on.
• 
If the preset picture modes are not sufficient, users can configure the  and  
directly using this mode.
• 
 This mode provides the picture setting appropriate for editing a document and surfing the Internet 
(text + picture).
•
This mode provides the picture setting appropriate for playing games that include lots of graphics and 
that require a fast screen refresh rate.
• 
This mode provides brightness and sharpness settings similar to those of a TV for the best 
entertainment environment (movie, DVD, etc.).
• 
Controls the picture contrast automatically so that bright and dark pictures are balanced overall.
 This menu is unavailable when  or  is set. 
Picture ModeThe Monitor has four automatic picture settings (, ,  and ) 
that are preset at the factory. You can activate either Dynamic, Standard, Movie or Custom. You can 
select Custom which automatically recalls your personalized picture settings.
• 
Select this mode to view a sharper image than in Standard mode.
• 
Select this mode when the surroundings are bright. This also provides a sharp image.
•
Select this mode when the surroundings are dark. This will save power and reduce eye fatigue.
• 
Select this mode when you want to adjust the image according to your preferences
 • This can only be set when the external input is connected through HDMI/DVI and  is set to .
• This menu is unavailable when  or  is set.
 
MenuDescription