Samsung Syncmaster 940ux Quick Start Guide

 
Quick Setup GuideWarranty Card 
(Not available in all locations)Users Guide, 
Monitor Driver, 
Natural Color software 
 
 
 Cable
  
 
D-sub Cable  Power Cord  
USB Cable
 
 
  Sold separately 
 
DVI-D Cable
 
 
 
 
 Front 
 
MENU button [ ] 
 Opens the OSD menu. Also use to exit the OSD menu or return to the 
previous menu.  
MagicBright™ [
] 
 MagicBright™ is a new feature providing optimum viewing environment 
depending on the contents of the image you are watching. Currently 
seven different modes...

 
 
  
 
 
 
 
Sport, Movie and Dynamic Contrast. Each mode has its own pre-
configured brightness value. You can easily select one of seven settings 
by simply pressing MagicBright™ control button.  
 
1) Custom  
Although the values are carefully chosen by our engineers, the pre-
configured values may not be comfortable to your eyes depending on 
your taste. 
If this is the case, adjust the brightness and contrast by using the 
OSD menu. 
2) Text  
For documentations or work involving a lot of text.
3)...

  (The configuration at the back of the monitor may vary from product to product.) 
 
 
 
   ON [ | ] / OFF [O]  
Switch the monitor on and off. 
 
 POWER  
Connect the power cord for your monitor to the  POWER on the back 
of the monitor.  
     
 
 
    
Connect the   of the monitor and the USB of the computer with the 
USB cable.
     
 
 
 
    
Connect the   of the USB monitor and a USB device with the USB 
cable.  
 
 
 
zTo use   (   ) , you have to connect the   ( 
 ) to the PC.   
zMake sure to...

 
     
 
RGB IN  
Connect the signal cable to the 15-pin, 
RGB IN on the back of your 
monitor.
     
 
 
 
Kensington Lock  
The Kensington lock is a device used to physically fix the system 
when using it in a public place. 
(The locking device has to be purchased separately.)  
 
 
 
 
For using a locking device, contact where you 
purchase it.
     
 
 
 
Stand Stopper 
Remove the fixing pin on the stand to lift the monitor up and down. 
See Connecting the Monitor for further information regarding...

 
 
 
 
Connecting the Monitor 
Connect the power cord for your monitor to the power port on the back of the monitor. 
Plug the power cord for the monitor into a nearby outlet.
Use appropriate connection for your computer.
 
Using the D-sub (Analog) connector on the video card. 
Connect the signal cable to the 15-pin, D-sub port on the back of your monitor.
 
[ RGB IN ]  
Using the DVI (Digital) connector on the video card. 
Connect the DVI Cable to the DVI IN port on the back of your monitor.
 
[ DVI IN...

 
You can use a USB device such as a mouse, keyboard, Memory Stick or external hard disk drive 
by connecting them to the     of the monitor without connecting them to the PC. 
The USB of the monitor supports High-Speed Certified USB 2.0.  
  High speed  Full speed  Low speed 
Data Rate 480 Mbps 12 Mbps 1.5 Mbps
 Connect the     of the monitor and the USB of the computer with the USB cable.  
 
 
 
 Connect the    of the USB monitor and a USB device with the USB cable.  
   The use procedures are as the...

zThe company is not liable for problems or damages to an external device caused by 
using an unauthorized cable for the connection.   
zSome products do not follow the USB standard, and it may cause a malfunction of the 
device.  
zIf the device malfunctions even if it is c
onnected to the computer, contact the service 
center of the device/computer.   
 
 
  
USB monitor  You can use this product as a monitor simply by connecting the power cable and the USB cable to your PC. 
 
 Minimum hardware...

  
   
  2.  Click I Accept.
    
   
   
  3.  The installation is started automatically and the insta
llation progress window is displayed, as shown in the 
figure below.  
   
zManual Installation: If the USB driver is not installed automatically, insert the provided USB Monitor 
Install CD into the CD-ROM drive of your PC. ‘Double-click My Computer on the Windows Desktop and 
click on User Manual (I:). The volume name of the re movable storage disk (for example, E:, F:, G: ) may 
be different...

   
   
5-3.  Arrange the monitors displayed in the Display Properties window in the order they are actually 
used.
   
   
   
5-4.  Then click OK button.
    
    
 
 Configuring the USB Monitor Display Information     
  1.  When the driver setup for the USB monitor is finished, a monitor icon is created in the system tray at the 
bottom of the monitor screen.
    
   
   
  2.  Click the monitor icon to display a list of connected USB monitors.  
Example) The following figure shows when two USB...

 
    
 
 Checking the configuration     
   After the installation, you can check the configuration by following these steps.
    
  1.  Right-click ‘My Computer’, and select ‘Properties’ – ‘System Properties’ – the ‘Hardware tab’.
    
  2.  Click ‘Device Manager’.
   
   
  3. A list of the installed device will be displayed, as shown in the figure below.
   
    
 
     The Initial Screen Settings after Installing the Program
 
Applicable mode: Extend mode 
Mode position: To the right of the primary...