Samsung Syncmaster 940bf Quick Start Guide

							Install drivers   Install programs  
SyncMaster 740BF / 940BF
 
						

							 
 
  Notational 
  
 
 
 
 
 
Failure to follow directions noted by this symbol could result in bodily harm or damage to 
equipment.  
 
 
 
Prohibited Important to read and understand at all times 
Do not disassemble Disconnect the plug from the outlet 
Do not touch Grounding to prevent an electric shock 
 
 
 
 
 
  Power 
  
When not used for an extended period of time, set your computer to DPMS.  
If using a screen saver, set it to the active screen mode.  
 
 
						

							 
 Do not use a damaged or loose plug. 
zThis may cause an electric shock or fire.  
 
 
 
  Do not pull the plug out by the wire nor touch the plug with wet hands. 
zThis may cause an electric shock or fire.  
 
 
 
  Use only a properly grounded plug and receptacle. 
zAn improper ground may cause electric shock or equipment damage.  
 
 
 
  Insert the power plug firmly so that it does not come loose. 
zA bad connection may cause fire.  
 
 
 
  
  Do not excessively bend the plug and wire nor place heavy objects upon 
them, which could cause damage.   
zThis may cause an electric shock or fire.  
 
 
 
  
  Do not connect too many extension cords or plugs to an outlet.   
zThis may cause fire.  
 
 
 
  
  Do not disconnect the power cord while using the monitor.   
zA surge may be caused by the separation and may damage the monitor. 
 
 
 
  
  Do not use the power cord when the connector or plug is dusty.   
zIf the connector or plug of the power cord is dusty, clean it with a dry 
cloth.  
zUsing the power cord with a dusty plug or connector may cause an 
electric shock or fire.  
 
 
 
 
 Installation  
 
						

							  
  
Be sure to contact an authorized Service Center, when installing your monitor in 
a location with the heavy dust, high or low temperatures, high humidity, chemical 
substance and where it operates for 24 hours such as the airport, the train 
station or etc. 
 
Failure to do so may cause a serious damage to your monitor. 
 
 
Put your monitor in a location with low humidity and a minimum of dust. 
zFailure to do so may cause an electric shock or fire inside the monitor.  
 
 
Do not drop the monitor when moving it. 
zThis may cause damage to the product or human body.  
 
 
Install the monitor base in a showcase or shelf so that the end of the 
base does not protrude from the showcase or shelf. 
zDropping the product may cause damage to the product or personal 
injury.  
 
 
Do not place the product on an unstable or small surface area. 
zPlace the product on an even, stable surface, as the product may fall 
and cause harm to someone walking by, specifically children.  
 
 
Do not place the product on the floor. 
zSomeone, specifically children could trip over it.  
 
 
Keep any flammable objects such as candles, insecticides or cigarettes 
away from the product. 
zOtherwise, this may cause a fire.  
 
 
Keep any heating devices away from the power cable. 
zA melted coating may lead to electric shock or fire.  
 
 
Do not install the product in places with poor ventilation, for instance, a 
bookshelf, closet, etc. 
zAny increase in internal temperature may cause fire.  
 
						

							 
 
Set down the monitor carefully. 
zThe monitor could be damaged or broken.  
 
 
Do not place the monitor face down. 
zThe TFT-LCD surface may be damaged.  
 
 
Installing a wall bracket must be done by a qualified professional. 
zInstallation by unqualified personnel may result in injury.  
zAlways use the mounting device specified in the owners manual.  
 
 
When installing the product, make sure to keep it away from the wall 
(more than 10 cm / 4 inch ) for ventilation purposes. 
zPoor ventilation may cause an increase in the internal temperature of the 
product, resulting in a shortened component life and degraded 
performance.  
 
 
Keep the plastic packaging (bag) out of children’s reach. 
zThe plastic packaging (bag) may cause suffocation if children play with 
it.  
 
 
 
 
 
  Clean  
  
When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with 
a slightly moistened, soft fabric. 
 
 
Do not spray water or detergent directly on the monitor. 
zThis may cause damage, electric shock or fire.  
 
 
Use the recommended detergent with a smooth cloth.  
 
						

							 
 
If the connector between the plug and the pin is dusty or dirty, clean it 
properly with a dry cloth. 
zA dirty connector may cause an electric shock or fire.  
 
 
Make sure to unplug the power cord before cleaning the product. 
zOtherwise, this may cause electric shock or fire.  
 
 
Unplug the power cord from the power outlet and wipe the product using 
a soft, dry cloth. 
zDo not use any chemicals such as wax, benzene, alcohol, thinners, 
insecticide, air freshener, lubricant or detergent.  
 
 
Contact the Service Center or Customer Center for interior cleaning 
once a year. 
zKeep the products interior clean. Dust which has accumulated in the 
interior over an extended period of time may cause malfunction or fire.  
 
 
 
 
 
  Others  
  
Do not remove cover (or back). 
zThis may cause an electric shock or fire.  
zRefer servicing to qualified service personnel.  
 
 
If your monitor does not operate normally - in particular, if there are any 
unusual sounds or smells coming from it - unplug it immediately and 
contact an authorized dealer or service.  
zThis may cause an electric shock or fire.  
 
 
Keep the product away from places exposed to oil, smoke or moisture; 
do not install inside a vehicle. 
zThis may cause malfunction, an electric shock or fire.  
zEspecially avoid operating the monitor near water or outdoors where it 
could be exposed to snow or rain.  
 
						

							 
 
If the monitor is dropped or the casing is damaged, turn the monitor off 
and unplug the power cord. Then contact the Service Center . 
zThe monitor may malfunction, causing an electric shock or fire.  
 
 
Disconnect the plug from the outlet during storms or lightening or if it is 
not used for a long period of time. 
zFailure to do so may cause an electric shock or fire.  
 
 
Do not try to move the monitor by pulling only the wire or the signal 
cable. 
zThis may cause a breakdown, electric shock or fire due to damage to 
the cable.  
 
 
Do not move the monitor right or left by pulling only the wire or the 
signal cable. 
zThis may cause a breakdown, electric shock or fire due to damage to 
the cable.  
 
 
Do not cover the vents on the monitor cabinet. 
zBad ventilation may cause a breakdown or fire.  
 
 
Do not place water containers, chemical products or small metal objects 
on the monitor. 
zThis may cause malfunction, an electric shock or fire.  
zIf a foreign substance enters the monitor, unplug the power cord and 
contact the Service Center.  
 
 
Keep the product away from combustible chemical sprays or 
inflammable substances. 
zThis may cause an explosion or fire.  
 
 
Never insert anything metallic into the monitor openings.  
zThis may cause an electric shock, fire or injury.  
 
 
Do not insert metal objects such as chopsticks, wire and gimlet or 
inflammable objects such as paper and match into the vent, headphone 
port or AV ports. 
zIt may cause a fire or an electric shock. If an alien substances or water 
 
						

							flows into the product, turn the product off, unplug the power connector 
from the wall outlet and contact Service Center.  
 
If you view a fixed screen for an extended period of time, residual image 
or blurriness may appear. 
zChange the mode to energy save or set a screensaver to moving picture 
when you need to be away from the monitor for an extended period of 
time.  
 
Adjust the resolution and frequency to the levels appropriate for the 
model. 
zInappropriate resolution may cause undesirable picture quality.  
 
17,19 inch (43, 48 cm) - 1280 X 1024 
 
Watching the monitor continuously at a too close angle may result in 
eyesight damage. 
 
 
To ease eye strain, take at least a five-minute break after every hour of 
using the monitor. 
 
Do not install the product on an unstable, uneven surface or a location 
prone to vibrations. 
zDropping the product may cause damage to the product or personal 
injury. Using the product in a location prone to vibrations may shorten 
the lifetime of the product or may catch fire. 
 
 
When moving the monitor, turn off and unplug the power cord.  
Make sure that all cables, including the antenna cable and cables 
connecting to other devices, are disconnected before moving the 
monitor. 
zFailure to disconnect cables may damage it and lead to fire or an electric 
shock.  
 
Place the product out of children’s reach, as they could damage it by 
hanging onto it. 
zA falling product could cause physical damage even death.  
 
 
When not using the product for an extended time period, keep the 
product unplugged. 
zOtherwise, this may cause heat emission from the accumulated dirt or 
 
						

							degraded insulation, leading to electric shock or fire.  
 
Do not place children’s favorite objects (or anything else that may be 
tempting) on the product. 
zChildren may try to climb on the product to retrieve an object. The 
product could fall, causing physical damage or even death.  
 
 
 
						

							 
 
 List of Features 
   RTA Monitor  
 
RTA(Response Time Accelerator)  
A function that accelerates the response speed of the panel so as to provide a sharper and 
more natural video display.
zRTA On   Activates the RTA function so that the panel operates at a higher 
response speed than  its original speed.
zRTA Off  Deactivates the RTA function so that the panel operates at its original 
response speed. 
( Note : If you turn the power off and on again a
fter switching RTA off, the RTA function is 
automatically switched  On (Factory Setting)
  
  
  
 
 
Please make sure the following items are included with your monitor.  If any items are missing,  contact your dealer.  
Contact a local deale
rto buy optional items.  
 
 
 
 
 Unpacking 
   
 Type 1 
 
 
 
Monitor & Simple stand  Bottom
MagicRotation™ program can not be provided as Simple