Samsung Syncmaster 930xt Quick Start Guide

							and worms across networks.  
You can think of a firewall as a sentinel which identifies incoming data from the Internet and other networks. 
According to the firewall settings, incoming data to your computer is either permitted or rejected.  
The Windows Firewall is, by default, installed and activated on your client. However, your administrator can 
turn it off. You can choose and select a different firewall. Therefore, it is not required for you to use the 
Windows Firewall. Estimate the functions of other firewalls and choose the best one to fit your 
requirements. To install and run a different firewall, you must turn off the Windows Firewall.  
 
You must be logged on as administrator to turn the Windows Firewall on or off. Follow these steps to turn 
the Windows Firewall on or off. 
1. Run the Windows Firewall.  
 
2. Click on one of these options under the General tab. 
{On (recommended) : This is the recommended setting for normal use.  {On with no exceptions : This settings blocks all unwanted access to your client, including all 
requests to programs and services selected in the Exceptions tab. Use this setting when you 
need to protect your client to the maximum extent.  
{Off (Not recommended) : Turning off the Windows Firewall may make your client and network 
more vulnerable to viruses and intruders.  
 
 
 
 
 
 
 
 
 
 Configuring Utilities 
Local Drive
 
  C Drive  
 
The C drive is used for the system. If there is less than 3MB of free space available, the client OS 
cannot operate. Therefore, always ensure that there is a sufficient amount of free space available. 
EWF can help maintain available space by preventing the C drive being written to directly. 
 
  Saving Files  
 
Your client uses a fixed size of flash memory. Therefore, it is better to save files to the server 
rather than to your client.
Mapping a Network Drive
 The administrator can map a folder to a network drive. To keep the mapping information after restarting 
the client, take note of these directions carefully.  
 
- Select the Reconnect at logon checkbox in the Map Network Drive dialog box.
- If the EWF or FBWF is enabled, the changes are saved on the disk.
Installing MUI (Multi-language User Interface)  
 The MUI Setup program helps you set up languages on the XPe client. In addition, you can delete an 
original language pack to extend the available free disk space. If you want to change the default 
language, standards or formats, use the Regional Options in the Control Panel.
 
To add a language to your XPe client, follow these steps:
- Log on as an administrator.
- If the EWF or FBWF is enabled, you must disable it before beginning the installation.
-Click Start and click Run . Type muisetup.exe in the Open box and click OK . A list of languages 
that can be installed is displayed as shown below.
- Select the language you want to install and click Install from the File menu. The installation will 
begin. 
 
 
						

							 
  
You can delete an original language pack using the Delete menu in the File menu.  
This operation deletes the original language pack only and does not delete the copy installed on your 
XPe Client.  
 
 
 
 Recover the System
Overview
  
 The XPe Client provides a recovery function which allows you to revert to a backed up system when 
encountering a serious problem. You can back up an OS image which is working normally to USB 
memory or the PXE server. You can revert to a backed up image when your client has one of these 
problems:  
 
When a system file is deleted accidentally or is corrupted 
 When the client computer is unstable or there is a problem with a device driver 
 When problems occur, after installing a new program or device 
 When the client computer is infected with a virus 
 When Windows XP Embedded fails to start 
How to Recover the System
 
 
Recovery Using USB Memory 
By following these steps, you can save all necessary files to USB memory, and boot up with the 
backed up system on the USB memory and recover the system.
- Perform system formatting for your USB memory in order to make it bootable.
- Save the Windows XP Embedded image and the Backup/Recovery Utility which will be 
recovered later to your USB memory.
- Boot up with the USB memory.
- Recover the system using the Windows XP Embedded image and the Backup/Recovery Utility 
in the USB memory.
 
 
 For more information, refer to the PXE Server User Manual. 
Recovery Using Network Booting
This method is provided through the PXE (Preboot eXecution Environment) server. The PXE sever 
provides a client/server interface based on TCP/IP, DHCP, and TFTP. It allows an administrator at 
a remote location to configure and boot the operating system onto a client over a network. 
- Implement a PXE server.
- Save the Windows XP Embedded image and the Backup/Recovery Utility which will be 
recovered later onto the PXE server.
- Boot the client via the network.
- Recover the system using the Windows XP Embedded image and the Backup/Recovery Utility 
saved on the PXE server via the network.
 
						

							 
 
 Monitor Driver 
When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the  directions appropriate for the operating system you have.  
 
Prepare a blank disk and download the driver program file at the Internet web site shown below.    
Internet web site : http://www.samsung.com/ (Worldwide)
http://www.samsung.com/monitor (U.S.A)
http://www.sec.co.kr/monitor (Korea)
http://www.samsungmonitor.com.cn
/(China)
Installing the Monitor Driver (Automatic)
 
Insert the CD into the CD-ROM drive. 
Click  Windows .
Choose your monitor model in the model list, then click the OK button.  
 
 
If you can see following message window, then click the Continue Anyway button. Then click the 
OK button (Microsoft® Windows® XP/2000 Operating System).   
 
						

							 
 
 
 
   
 
 
 
This monitor driver is under certifying MS logo, and this installation doesnt damage your 
system.  
The certified driver will be posted on Samsung Monitor homepage  
 
http://www.samsung.com/ 
Monitor driver installation is completed. 
Installing the Monitor Driver (Manual)
Windows Vista | Windows XP | Windows 2000 | Windows ME | Windows NT | Linux 
Microsoft® Windows Vista™ Operating System   
 
Insert your Manual CD into your CD-ROM drive.
Click  (Start) and Control Panel. Then, double-click on Appearance and Personalization.  
 
 
   
Click Personalization and then Display Settings.  
 
 
   
Click Advanced Settings….  
  
 
						

							 
Click Properties in the Monitor tab. If the Properties button is deactivated, it means the 
configuration for your monitor is completed. The monitor can be used as is. 
If the message “Windows needs…” is displayed, as shown in the figure below,  
click Continue. 
 
 
    
This monitor driver is under certifying MS logo, and this installation doesnt damage your 
system.  
The certified driver will be posted on Samsung Monitor homepage  
 
http://www.samsung.com/ 
Click Update Driver… in the Driver tab.  
 
 
   
Check the Browse my computer for driver software checkbox and click Let me pick from a list 
of device drivers on my computer.  
 
 
   
Click Have Disk… and select the folder (for example, D:\Drive) where the driver setup file is 
located, and click OK.  
 
   
Select the model that matches your monitor from the list of monitor models on the screen, and 
click Next.  
 
						

							 
    
 
Click Close→ Close → OK → OK on the following screens displayed in sequence. 
   
   
Microsoft® Windows® XP Operating System  
 
Insert the CD into the CD-ROM drive.
Click Start → Control Panel then click the Appearance and Themes icon.  
  
 
Click Display icon and choose the Settings tab then click Advanced.  
  
 
						

							 
Click the Properties button on the Monitor tab and select Driver tab.  
     
 
Click Update Driver. and select Install from a list or. then click the Next button.  
   
 
Select Dont search ,I will. then click Next and then click Have disk.  
  
 
Click the Browse button then choose A:(D:\Driver) and choose your monitor model in the model 
list and click the Next button.  
  
 
If you can see following Message window, then click the Continue Anyway button. Then click 
the OK button.  
 
						

							 
 
 
   
 
 
This monitor driver is under certifying MS logo, and this installation doesnt damage your 
system.  
The certified driver will be posted on Samsung Monitor homepage  
 
http://www.samsung.com/ 
Click the Close button then click the OK button continually.  
  
 
Monitor driver installation is completed.  
 
Microsoft® Windows® 2000 Operating System  
 
 When you can see Digital Signature Not Found on your monitor, follow these steps.  
 
 
How to install 
Choose the OK button on the Insert disk window. 
Click the Browse button on the File Needed window. 
Choose A:(D:\Driver) then click the Open button and then click the OK button. 
Click Start, Setting, and then Control Panel. 
Double click the Display icon. 
Select the Settings tab and click the Advanced Properties button. 
Choose Monitor.  
Case1 : If the Properties button is inactive, it means your monitor is properly configured. Please 
stop installation 
Case2 : If the Properties button is active, click the Properties button then follow next steps 
continually.
Click Driver and then click Update Driver. then click the Next button. 
Choose Display a list of the known drivers for this device so that I can choose a specific driver 
then click Next and then click Have disk.
Click the Browse button then choose A:(D:\Driver). 
Click the Open button, then click the OK button. 
Choose your monitor model and click the Next button then click Next button. 
Click the Finish button then the Close button.  
 
If you can see the Digital Signature Not Found window then click the Yes button. And click the 
Finish button then the Close button. 
Microsoft® Windows® Millennium Operating System    
 
Click Start, Setting, and then Control Panel. 
Double click the Display icon. 
Select the Settings tab and click the Advanced Properties button. 
Select the Monitor tab. 
 
						

							 
 
 
 
 
Click the Change button in the Monitor Type area. 
Choose Specify the location of the driver. 
Choose Display a list of all the driver in a specific location. then click the Next button. 
Click the Have Disk button. 
Specify A:\(D:\driver) then click the OK button. 
Select Show all devices and choose the monitor that corresponds to the one you connected to 
your computer and click OK. 
Continue choosing Close button and OK button until you close the Display Properties dialogue 
box. 
Microsoft® Windows® NT Operating System    
 
Click Start, Settings, Control Panel, and then double-click Display icon.
In the Display Registration Information window, click the Settings tab and then click All Display 
Modes.
Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and 
then click OK. 
Click the Apply button if you see the screen working normally after clicking Test. If the screen 
is not normal, change to a different mode (lower mode of resolution, colors, or frequency). 
If there is no Mode at All Display Modes, select the level of resolution and vertical 
frequency by referring to the Preset Timing Modesin the user guide.
Linux Operating System    
 
To execute X-Window, you need to make the X86Config file, which is a type of system setting file.  
 
Press Enter at the first and the second screen after executing the X86Config file. 
The third screen is for setting your mouse. 
Set a mouse for your computer. 
The next screen is for selecting a keyboard. 
Set a Keyboard for your computer. 
The next screen is for setting your monitor. 
First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.) 
Set a vertical frequency for your monitor. (You can enter the frequency directly.) 
Enter the model name of your monitor. This information will not affect the actual execution of X-
Window. 
You have finished setting up your monitor.  
Execute X-Window after setting other requested hardware. 
 
 Natural Color 
Natural Color
One of the recent problems in using a computer is that the color of the images printed out by a printer 
or other images scanned by a scanner or a digital camera are not the same as those shown on the 
 
						

							 
 
 
  monitor.  
the Natural Color S/W is the very solution for this problem. It is a color administration system 
developed by Samsung Electronics in association with Korea Electronics & Telecommunications 
Research Institute (ETRI).  
This is only available for Samsung monitors and ensures that the color of the images on the monitor 
are the same as the printed or scanned images.  
For more information, refer to Help (F1) in the software program.  Installing the Natural Color Software 
Insert the CD included with the Samsung monitor into the CD-ROM Drive. The initial Natural Color 
screen will appear. Click on Natural Color in the startup window to install the Natural Color software.  
To install the program manually, insert the CD included with the Samsung monitor into the CD-ROM 
Drive, click the Windows [Start] button, select [Run...] .  
Enter D:\Color\NCProSetup.exe and then press the  key.  
(If the drive where the CD is inserted is not D:\, enter the applicable drive.) 
Uninstalling the Natural Color Software Program
Select Settings / Control Panel from the Start menu and then double-click Add/Delete a 
program  
Select Natural Color from the list and then click the Add/Delete button. 
MagicTune™
 
 
Installation 
 
1. Insert the installation CD into the CD-ROM drive. 
2. Click the MagicTune™ installation file.  
3. Select installation Language, Click Next. 
4. When the Installation Shield Wizard window appears, click Next.  
5. Select I agree to the terms of the license agreement to accept the terms of use.  
6. Choose a folder to install the MagicTune™ program. 
7. Click Install. 
8. The Installation Status window appears. 
9. Click Finish. 
10. When the installation is complete, the MagicTune™ executable icon appears on your desktop.  
 
Double-click the icon to start the program.  
 
 
 
MagicTune™ execution icon may not appear depending on specification 
of computer system or monitor.  
If that happens, press F5 Key.
  
 
 Installation Problems (MagicTune™) 
 
The installation of MagicTune™ can be affected by such factors as the video card, motherboard and the 
network environment.  
 
 
 
 System Requirements
 
OS 
zWindows 2000  zWindows XP Home Edition  zWindows XP Professional  zWindows Vista™  
 
It is recommended using MagicTune™ in Windows® 2000  
or later.