Samsung Syncmaster 710m Quick Start Guide

MenuDescription
AUTOWhen the 
AUTO button is pressed, the Auto Adjustment screen appears as 
shown in the animated screen on the center. 
Auto adjustment allows the monitor to se lf-adjust to the incoming video signal. 
The values of fine, coarse and position are adjusted automatically.  
 
To make the automatic adjustment function sharper, execute the AUTO function 
while the  AUTO PATTERN  is on.
 
 
 MagicBright™ 
 
MenuDescription
MagicBright™ Then push the MagicBright™ button 
again to circle...

- four different mode (Custom/Text/Internet/Entertain)  
 
 Brightness 
MenuDescription
BrightnessAdjust Brightness. 
 
 
 
 

MenuDescriptionPlay/Stop
BrightnessAdjust the Brightness.  
Direct Access Feature 
: When OSD is not on the screen, Push 
the button to adjust brightness. 
ContrastAdjust the Contrast. 
 
 
 Color 
MenuDescriptionPlay/Stop
Color Tone The tone of the color can be changed and one of four modes 
can be selected - Cool, normal, Warm and Custom.
 Picture 
 

Color ControlFollow these steps to adjust individual R,G,B color balance.
GammaSelect one of three pre-defined gammas.
 
 
 Image 
MenuDescriptionPlay/Stop
CoarseRemoves noise such as vertical stripes. Coarse adjustment may 
move the screen image area. You 
may relocate it to the center 
using the Horizontal Control menu.
Fine
Removes noise such as horizontal stripes. If the noise persists 
even after Fine tuning,  
repeat it after adjusting the frequency (clock speed).
Sharpness Follow these instuction...

MenuDescriptionPlay/Stop
LanguageFollow these steps to change th
e language used in the menu. 
You can choose one of seven languages. (English, German, 
Spanish, French, Italian, Swedish, Russian) 
Note :The language chosen affects only the language of the 
OSD. It has no effect on any software running on the computer.
H-PositionYou can change the horizontal position where the OSD menu 
appears on your monitor.
V-Positon You can change the vertical position where the OSD menu 
appears on your monitor....

MenuDescriptionPlay/Stop
Image ResetImage parameters are replaced with the factory default values.
Color ResetColor parameters are replaced wi th the factory default values.
 
 
 Information 
MenuDescription
InformationShows a video source, display mode on the OSD screen. 
 Setup 
 

 
 
Before calling for service, check the information in this section to see if you can remedy any 
problems yourself. If you do need assistance,  please call the phone number on the warranty card, 
the phone number on the Informatio n section or contact your dealer.
 
 
SymptomCheck ListSolutions
No images on the 
screen. I cannot turn 
on the monitor.Is the power cord connected properly?Check the signal cable connection.
Can you see  Check Signal Cable  on 
the screen? Check the signal cable...

 
one minute and then disappears.  
Please change to the recommended 
mode during this one-minute period.  
(The message is displayed again if the 
system is rebooted.) 
There is no image on the screen.  
Is the power indicator on the monitor 
blinking at 1 second intervals?The monitor is in PowerSaver mode. 
 
Press a key on the keyboard or move 
the mouse to activate the monitor and 
restore the image on the screen.
The screen shows 
strange colors or just 
black and white.Is the screen displaying only...

driver and the monitor driver.  
4. Check if the scanning ratio of the video screen is set at 75Hz.  
(Do not exceed 60Hz when using the maximum resolution.)  
5. If you have problems in installing  the adapter (video) driver, boot the computer in Safe Mode, remove the 
Display Adapter at the  Control Panel→System →Device Administrator  and then reboot the 
computer to reinstall the  adapter (video) driver.  
 
 If problems repeatedly occur,  contact an authorized service center .
 
 
 Q & A...

 
 
Failure of any of the boxes to appear indicates a  problem with your monitor. This box also appears 
during normal operation if the video ca ble becomes disconnected or damaged. 
 
4. Turn off your monitor and reconnect the video cable;  then turn on both your computer and the monitor.  
If your monitor screen remains blank after us ing the previous procedure, check your video 
controller and computer system; your  monitor is functioning properly. 
  
 Warning Messages  
 
If there is something wrong...