Samsung Syncmaster 2433bw User Manual

							Your Monitor
Initial Settings
Select the language using the up or down key.
The displayed content will disappear after 40 seconds.
Turn the Power button off and on. It will be displayed again.
It can be displayed up to 
three 
(3) times. Make sure to adjust the resolution of your PC before reaching
the maximum count.  Note
The resolution displayed on the screen is the optimal resolution for this product.
Adjust your PC resolution so that it is the same as the optimal resolution for this product.
Front MENU button [MENU/ ]
Opens the on-screen menu and exits from 
 the menu. Also use to exit the OSD menu
or return to the previous menu. Brightness button [ ]
When OSD is not on the screen, push the button to adjust brightness.
>> Click here to see an animation clip Customized Key[ ]
You can customize key assignment for the 
 Custom button according to your pref-
erences. Introduction
10
 
						

							 Note
You can configure the customized key for  a 
required function via Setup > Cus-
tomized Key. Adjust buttons [ ]
These buttons allow you to adjust items in the menu. Enter button [ ]
Activates a highlighted menu item.
Push the ' ', then selects the video signal while the OSD is off. (When the 
button is pressed to change the input mode, a message appears in the upper left of
the screen displaying the current mode -- analog or digital input signal.)
 Note
If you select the digital mode, you  must 

connect your monitor to the graphic card's
DVI port using the DVI cable.
>> Click here to see an animation clip AUTO button
Use this button for auto adjustment.
>> Click here to see an animation clip
Power button [
 Note
See PowerSaver described in the manual for  further 

information regarding power
saving functions. For energy conservation, turn your monitor OFF when it is not
needed or when leaving it unattended for long periods.
Rear  Note
The configuration at the back of the monitor may vary from product to product. Introduction
11]
Use this button for turning the product on and off.
  Power Indicator
This light is lit when operating normally, and blinks once when your adj\
ustments
are saved.
 
						

							POWER port
Connect  the  power  cord  for  your 
monitor 
to  the  POWER  port  on  the  back  of  the
monitor. DVI IN port
Connect the DVI Cable to the DVI IN port on the back of your monitor.
RGB IN port
Connect the D-sub cable to the 15-pin, RGB IN port on the back of your monitor.
Kensington Lock
The Kensington lock is a device 
used 

to physically fix the system when using it in a
public place. (The locking device has to be purchased separately.) For using a locking
device, contact where you purchase it.  Note
The location of the Kensington Lock may be different depending on its model.
Using the Anti-Theft Kensington Lock
1. Insert the locking device into the Kensington slot on the Monitor  and turn it
in the locking direction  .
2. Connect the Kensington Lock cable.
3. Fix the Kensington Lock to a desk or a heavy stationary object.  Note
See Connecting Cables for further information regarding cable connections. Introduction
12
 
						

							Cable holding ring
•
Fix the cables using the holding ring, as shown in the figure. Introduction
13 
						

							Connections
Connecting Cables
 Connect the power cord for your monitor to the power port on the back of the monitor.
Plug the power cord for the monitor into a nearby outlet.  Use a connection appropriate for your computer.
 Using the D-sub (Analog) connector on the video card.
• Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. [RGB IN]
 Using the DVI (Digital) connector on the video card.
• Connect the DVI Cable to the DVI IN Port on the back of your Monitor. [DVI IN]
 Connected to a Macintosh.
• Connect the monitor to the Macintosh computer using the D-sub connection cable.  Note
If the monitor and the computer are connected, you can turn them on and use them. 14 
						

							Using the Stand
Folding the base
 Note
You can tilt the monitor upwards at an angle of -1° to16°.
Attaching a Base This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad. A. Monitor
B. Mounting interface pad (Sold separately)
1. Turn off your monitor and unplug its power cord.
2. Lay the LCD monitor face-down on a flat surface with  a 
cushion beneath it to protect the screen.
3. Remove four screws and then remove the stand from the LCD monitor.
4. Align the mounting interface pad with the holes in the rear cover mounting pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base. • Do not use screws longer than the standard dimension, as they may damage the
inside of the Monitor. Connections
15
 
 
 
( 
± 1.0°) 
 
						

							• For wall mounts that do not comply with VESA standard screw specifications,
the length of the screws may differ depending on their specifications.
• Do not use screws  that 
do not comply with the VESA standard screw specifica-
tions.
Do not fasten the screws too tightly, as this may damage the product or cause the
product to fall, leading to personal injury.
Samsung is not liable for these kinds of accidents.
• Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is used or the consumer fails to follow the product
installation instructions. • To mount the monitor on a wall, you should purchase the wall mounting kit that
allows you to mount the monitor at least 10 cm away from the wall surface.
• Contact  the  nearest  Samsung  Service 

Center  for  more  information.  Samsung
Electronics will not be responsible for damages caused by using a base other than
those specified.
• Please use Wall Mount according to the International standards. Connections
16
 
						

							Using the Software
Monitor Driver
 Note
When prompted by the operating system for the monitor driver, insert the CD-ROM
included with this monitor. Driver installation  is 
slightly different from one operating
system  to  another.  Follow  the  directions  appropriate  for  the  operating  system  you
have.
Prepare  a  blank  disk  and  download  the  driver  program  file  at  the  Internet  web  site
shown here.
Internet web site :
http://www.samsung.com/ (Worldwide) Installing the Monitor Driver (Automatic)
1. Insert CD into the CD-ROM drive.
2. Click "Windows".
3. Choose your monitor model in the model list, then click the "OK" button. 4. If you can see following message window, then click the "Continue Anyway" button. Then click
"OK" button (Microsoft ®
 Windows ®
 XP/2000 Operating System). 17
 
						

							 Note
This monitor driver is under certifying  MS 
logo, and this installation doesn't damage your system.
The certified driver will be posted on Samsung Monitor homepage.
http://www.samsung.com/
Installing the Monitor Driver (Manual) Microsoft®
 Windows Vista™‚ Operating System
1. Insert your Manual CD into your CD-ROM drive.
2. Click  (Start) and "Control Panel". Then, double-click on "Appearance and Personalization".
3. Click "Personalization" and then "Display Settings".
4. Click "Advanced Settings...".
 
5. Click  "Properties"  in  the  "Monitor"  tab.  If  the  "Properties"  button  is  deactivated,  it  means  the configuration for your monitor is completed. The monitor can be used as is.
If the message "Windows needs..."  is 

displayed, as shown in the figure below, click "Continue".
Using the Software
18
 
						

							 Note
This monitor driver is under certifying  MS 
logo, and this installation doesn't damage your system.
The certified driver will be posted on Samsung Monitor homepage.
6. Click "Update Driver..." in the "Driver" tab. 7. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a
list of device drivers on my computer". 8. Click "Have Disk...” and select the folder (for example, D:\Drive) where the driver setup file is
located, and click "OK". Using the Software
19