Samsung Syncmaster 2033hd User Manual

							Installing the Product2-1
2 Installing the Product
2-1 Package Contents
 
• Unpack the product and check if all of the following contents have been included.
• Store the packaging box in case you need to move the product at a later stage.
 
 The cleaning cloth is supplied with black high-glossy models only.
 
CONTENTS
Installation Manual Product Warranty
(Not available in all locations)User Manual D-Sub Cable
Power Cord Batteries (AAA X 2) Cable holding ring Stand
Remote Control Stereo Cable Cleaning Cloth
SOLD SEPARATELY
DVI Cable
 
						

							2-2Installing the Product
2-2 Installing the Stand
 Before assembling the product, place the product down on a flat and stable surface so that the screen is facing downwards. 
Place a soft cloth over the table to protect the product and place the product onto the 
cloth face down.
Insert the Stand Connector into the Stand in the direction shown by the 
figure.               
Turn the connecting screw at the bottom of the stand fully so that it is completely fixed.
- Caution
Do not lift the product holding only the stand
 
						

							Installing the Product2-3
2-3 Removing the Stand
 Before removing the stand, place the product down on a flat and stable surface so that the screen faces downwards. 
Place a soft cloth over the table to protect the product and place the product face down.
Turn the connecting screw at the bottom of the stand to separate it.
Take the Stand Connector out of the Stand by pulling it in the direction of the arrow as 
shown in the figure.
- Caution
Do not lift the product holding only the stand
 
						

							2-4Installing the Product
2-4 Attaching a Wall Mount/Desktop Stand
Attaching a Wall Mount/Desktop Stand(not supplied)
This product provides a stand mount of 75 mm x 75 mm (2.95 x 2.95 inches) that complies with the VESA specifications.
1.Turn the product off and unplug the power cord from the wall outlet.
2.Place a soft cloth or cushion on a flat surface to protect the panel and place the product face down.
3.Remove the screw from the stand and separate the stand.
4.Align the groove of the part of the product that is to be connected to the stand with the groove in the stand (desk-top stand, 
wall mount stand or another stand) and firmly fix the stand by fastening the screw.
 • If you use screw that is longer than the standard specifications, the inside of the product may be damaged.
• For wall mounts that are not compatible with the standard VESA specifications, the length of the screw may differ depending on the 
corresponding specifications.
• Avoid using screws that are incompatible with the standard VESA specifications and avoid assembling them using excessive force.
This may result in damage to the product or injury due to the product falling. Samsung shall not be held liable for any 
damage or injury.
• Samsung shall not be held liable for any damage to the product or injury caused by using a stand that is not compatible with the 
specified specifications or due to an installation not performed by an authorized installation engineer.
• When installing the product using a wall mount, purchase a wall mount that provides at least 10 cm (3.93 inches) of space from the 
wall.
• Use the wall mount according to the international specifications.
 
A. Wall/Desktop Stand Mount
B. Wall mount kit/desktop stand (not supplied)
 
						

							Installing the Product2-5
2-5 Connecting to a Computer
1. Connect the product to a PC depending on the video output supported by the PC.
 The connecting part may differ depending on the product model. 
When the graphics card provides a D-Sub  output
• Connect the [PC IN] port of the product to the [D-Sub] port of the PC with the D-Sub cable. 
When the graphics card provides a DVI  output
 
						

							2-5Installing the Product
• Connect the [DVI-D IN] port of the product to the DVI port of the PC with the DVI cable.
2. Connect the [ HDMI/PC/DVI-D AUDIO IN] port on the rear side of the monitor to the sound card of the PC.
3. Connect one end of the power cord to the [ POWER ] port of the product and connect the other end of the power cord to the 
220V or 110V wall outlet.
(The input voltage is switched automatically.)
 
						

							Installing the Product2-5
 
• You may enjoy clear and quality sound from the computer sound card using the monitors speakers. (You dont need to install 
separate speakers for your computer.)
• You may get a blank screen depending on the type of video card you are using if you connect the D-sub and DVI cables 
simultaneously to one computer.
• If you connect your monitor properly using the DVI connector but get a blank or fuzzy screen, check to see if the monitor status 
is set to analog. Press [ ] button to have the monitor double-check the input signal source.
 
 
						

							2-6Installing the Product
2-6 Using it as a TV
You may view television programs on the monitor if it is connected to an antenna or cable/satellite system without installing any 
separate TV reception hardware or software on your computer.
1.Connect the cable/satellite or TV antenna cable to the [ANT IN] port on the rear side of the monitor. 
• When using an indoor antenna/cable/satellite terminal:
Check the antenna terminal on the wall and then connect the antenna/cable/satellite TV cable.
• When using an outdoor antenna:
When using an outdoor antenna, we strongly suggest using a qualified technician to install it.
2.When the connections are completed, connect the TV power.
3.When the product is turned on for the first time after it was purchased, the initial setup operations () begin. 
 
• Be careful that the coaxial cable is not bent when connecting it to the antenna input terminal [ANT IN]. 
 
						

							Installing the Product2-7
2-7 Connecting an HDMI cable
Connect the HDMI OUT port of the AV device (Blu-Ray/DVD/Cable/Satellite box) to the [HDMI IN] terminal of the monitor using 
the HDMI cable. 
Press the [SOURCE] button at the front of the monitor or on the remote control to select  mode.
 You do not need to make a separate audio connection when connecting via HDMI. 
 
						

							2-8Installing the Product
2-8 Connecting Using a DVI to HDMI Cable 
1. Connect the DVI output terminal of an external device to the [HDMI IN] terminal of the monitor using a DVI to HDMI cable. 
2. Connect the red and white jacks of an RCA to stereo (for PC) cable to the same colored audio output terminals of the digital 
output device, and connect the opposite jack to the [HDMI/PC/DVI-D AUDIO IN] terminal of the product.
Press the [SOURCE] button at the front of the monitor or on the remote control to select  mode.