Samsung Syncmaster 2032mw Quick Start Guide

							 
5. Select AV or S-Video using the 
SOURCE. 
 
 
  
2. Connecting EXT.(RGB) - It only applies to AV DEVICE that supports SCART. 
Connect to the DVD Devices input if the device has a EXT (RGB) jack.  
You can watch DVD simply by hooking up the DVD player with the monitor as long as the power is on. 
1. Connect the 
EXT (RGB) port of the monitor to the DVD Player using a SCART jack. 
 
2. Select Ext. by using the 
SOURCE.  
 
3. Connecting TV 
You may view television programs on the monitor if it is connected to an antenna or CATV cable without 
installing any separate TV reception hardware or software on your computer. 
1. Connect the CATV cable or TV antenna cable to the ANT IN port on the rear side of the monitor.  
Make sure to use a TV antenna cable (sold separately) as the antenna cable. 
 
 
2. Turn on the monitor. 
   When using an interior antenna terminal: 
     Check the antenna terminal on the wall first and connect the antenna cable.
  When using an outdoor antenna: 
     If you are using an outdoor antenna, use a professional it for installation if possible.
  To connect the RF cable to the antenna input terminal: 
     Keep the copper wire portion of the RF cable straight.
 
						

							 
 3. Select TV using the 
SOURCE. 
 
4. Select a desired TV channel.  
Is weak signal causing poor reception? 
     Purchase and install a signal amplifier for better reception. 
4. Connecting DVD/DTV Set Top Box 
Connect to the DVD/DTVSet Top Box input if the device has a DVD/DTV connector.  
You can watch Component simply by hooking up the Component with the monitor as long as the power is 
on. 
1. Connect the port of the DVD, VCR (DVD / DTV Set-Top Box) to the 
R-AUDIO-L port of the monitor. 
 
2. Connect the VIDEO OUT port of the DVD / DTV Set-Top Box to the P
R, PB,Y input ports using a 
component video cable (PR, PB,Y). 
 
3. Select Component using the 
SOURCE.  
 
 
5. Connecting HDMI 
You cannot connect a PC to the 
HDMI IN terminal. 
1. Input devices such as digital DVD are connected to the 
HDMI IN terminal of the monitor using the 
HDMI cable.  
 
 
						

							 
 2. Then, start the DVD with a DVD disc inserted.  
 
3. Select HDMI using the 
SOURCE button.  
 
 
 
6. Connecting Using a DVI to HDMI Cable 
1. Connect the DVI output terminal of a digital output device to the 
HDMI IN terminal of the monitor 
using a DVI to HDMI cable.  
 
2. Connect the red and white jacks of an RCA to stereo (for PC) cable to the same colored audio 
output terminals of the digital output device, and connect the opposite jack to the 
HDMI / PC / DVI-
D AUDIO IN terminal of the monitor. 
 
3. Then, start the DVD with a DVD disc inserted.  
 
4. Select HDMI using the 
SOURCE button.  
 
 
 
 Using the Stand 
 
1. Folding the base 
You can tilt the monitor upwards at an angle of 0° to18° 
 
						

							 
 
 
 Installing the monitor driver (Automatic) 
When prompted by the operating system for the monitor driver, insert the CD-ROM included 
with this monitor. Driver installation is slightly different from one operating system to 
another. Follow the directions appropriate for the operating system you have. 
 
Prepare a blank disk and download the driver program file at the Internet web site shown here. 
 
zInternet web site :  http://www.samsung.com/ (WorldWide)
http://www.samsung.com/monitor (U.S.A)
http://www.sec.co.kr/monitor (Korea)
http://www.samsungmonitor.com.cn/ (China)
   
1. Insert CD into the CD-ROM drive.  
2. Click 
Windows  
3. Choose your monitor model in the model list, then click the 
OK button. 
 
 
 
4. If you can see following message window, then click the 
Continue Anyway button. Then 
click 
OK button. (Microsoft
® Windows® XP Operating System) 
 
 
 
5. Monitor driver installation is completed.  
 
This monitor driver is under certifying MS logo,and this installation dont damage 
your system.The certified driver will be posted on Samsung Monitor Homepage.  
http://www.samsung.com/ 
 
 
 
 Installing the monitor driver (Manual) 
Windows Vista | Windows XP | Windows 2000 | Windows ME | Windows NT | Linux
 
 
						

							 When prompted by the operating system for the monitor driver, insert the CD-ROM included 
with this monitor. Driver installation is slightly different from one operating system to 
another. Follow the directions appropriate for the operating system you have. 
 
Prepare a blank disk and download the driver program file at the Internet web site shown below. 
 
zInternet web site :  http://www.samsung.com/ (Worldwide)
http://www.samsung.com/monitor (U.S.A)
http://www.sec.co.kr/monitor (Korea)
http://www.samsungmonitor.com.cn/ (China)
Microsoft® Windows Vista™ Operating System  
 
1. Insert your Manual CD into your CD-ROM drive.
2. Click (Start) and 
Control Panel. Then, double-click on 
Appearance and Personalization. 
 
 
 
   
3. Click 
Personalization and then 
Display Settings.  
 
 
   
4. Click 
Advanced Settings….  
  
 
5. Click 
Properties in the 
Monitor tab. If the 
Properties button is deactivated, it means the 
configuration for your monitor is completed. The monitor can be used as is. 
If the message “
Windows needs…” is displayed, as shown in the figure below,  
click 
Continue. 
 
						

							 
 
    
This monitor driver is under certifying MS logo, and this installation doesnt damage 
your system.  
The certified driver will be posted on Samsung Monitor homepage.  
 
http://www.samsung.com/ 
6. Click 
Update Driver… in the 
Driver tab.  
 
 
   
7. Check the 
Browse my computer for driver software checkbox and click 
Let me pick from a 
list of device drivers on my computer.  
 
 
   
8. Click 
Have Disk… and select the folder (for example, D:\Drive) where the driver setup file is 
located, and click 
OK.  
 
   
9.
Select the model that matches your monitor from the list of monitor models on the screen, and 
click 
Next.  
 
						

							  
 
10. Click 
Close
→ 
Close 
→ 
OK 
→ 
OK on the following screens displayed in sequence. 
   
   
 
  Microsoft® Windows® XP Operating System 
 
1. Insert CD into the CD-ROM driver.  
2. Click 
Start 
→ 
Control Panel then click the 
Appearance and Themes Icon.  
 
     
 
3. Click 
Display icon and choose the 
Settings tab then click 
Advanced... 
 
 
						

							     
 
4. Click the 
Properties button on the 
Monitor tab and select 
Driver tab.  
 
     
 
5. Click 
Update Driver.. and select 
Install from a list or.. then click 
Next button.  
 
     
 
6. Select 
Dont search ,I will.. then click 
Next and then click 
Have disk.  
 
     
 
7. Click the 
Browse button then choose A:(D:\Driver) and choose your monitor model in the model list 
and click the 
Next button.  
 
 
						

							     
 
8. If you can see following message window, then click the 
Continue Anyway button. Then click 
OK 
button. 
 
  
 
This monitor driver is under certified MS logo,and this installation doesnt damage your system.The 
certified driver will be posted on Samsung Monitor Homepage.  
http://www.samsung.com/ 
 
9. Click the 
Close button then click 
OK button continually. 
 
 
 
     
 
10. Monitor driver installation is completed.  
 
 
 
   Microsoft® Windows® 2000 Operating System 
 
When you can see Digital Signature Not Found on your monitor, follow these steps.
1. Choose 
OK button on the 
Insert disk window.  
2. Click the 
Browse button on the 
File Needed window.  
3. Choose A:(D:\Driver) then click the Open button and then click 
OK button. 
How to install
 
						

							1. Click 
Start , 
Setting , 
Control Panel.  
2. Double click the 
Display Icon.  
3. Choose the 
Settings tab and then click 
Advanced...  
4. Choose 
Monitor.  
5. Click 
Driver and then click on 
Update Driver.. then click on the Next button.  
6. Choose 
Display a list of the known drivers for this device so that I can choose a specific 
driver then click 
Next and then click 
Have disk.  
7. Click the 
Browse button then choose A:(D:\Driver).  
8. Click the 
Open button, then click 
OK button.  
9. Choose your monitor model and click the 
Next button then click 
Next button.  
10. Click the 
Finish button then the 
Close button.  
If you can see the 
Digital Signature Not Found window then click the 
Yesbutton. And click 
the 
Finish button then the 
Close button.  Case1: If the Properties button is inactive, it means your monitor is properly configured. Please 
stop installation 
Case2: If the Properties button is active, click the Properties button then follow next steps 
continually.
 
 
   Microsoft® Windows® Millennium Operating System 
 
1. Click 
Start , 
Setting , 
Control Panel.  
2. Double click 
Display icon.  
3. Select the 
Settings tab and click 
Advanced Properties button.  
4. Select the 
Monitor tab.  
5. Click the 
Change button in the 
Monitor Type area.  
6. Choose 
Specify the location of the driver.  
7. Choose 
Display a list of all the driver in a specific location.. then click 
Next button.  
8. Click the 
Have Disk button  
9. Specify A:\(D:\driver) then click 
OK button.  
10. Select 
Show all devices and choose the monitor that corresponds to the one you connected to 
your computer and click 
OK.  
11. Continue choosing 
Close button and 
OK button until you close the Display Properties dialogue 
box.  
 
 
 
   Microsoft® Windows® NT Operating System 
 
1. Click 
Start, 
Settings, 
Control Panel, and then double-click 
Display icon.  
2. In Display Registration Information window, click Settings Tab and then click 
All Display Modes.  
3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then 
click 
OK.  
4. Click 
Apply button if you see the screen working normally after clicking 
Test. If the screen is not 
normal, change to a different mode (lower mode of resolution, colors or frequency).  
If there is no Mode at 
All Display Modes, select the level of resolution and vertical frequency 
by referring to the Preset Timing Modes in the user guide.
 
 
   Linux Operating System 
 
        To execute X-Window, you need to make the X86Config file, which is a type of system setting file.  
 
1. Press Enter at the first and the second screen after executing the X86Config file.  
2. The third screen is for 
setting your mouse.  
3. Set a mouse for your computer.  
4. The next screen is for 
selecting a keyboard.  
5. Set a Keyboard for your computer.  
6. The next screen is for 
setting your monitor.  
7. First of all, set a 
horizontal frequency for your monitor. (You can enter the frequency directly.)  
8. Set a 
vertical frequency for your monitor. (You can enter the frequency directly.)  
9. Enter the 
model name of your monitor. This information will not affect the actual execution of X-
Window.  
10. You have 
finished setting up your monitor.  
Execute X-Window after setting other requested hardware.