Samsung Sp U300m User Manual

							Installation and Connection2-2-1
2-2-1 Installing the Projector
 Install the projector so that the beam from the projector is perpendicular to the screen. 
•Place the projector so that the lens is at the center of the screen. If the screen is not vertically installed, the picture on the 
screen may not be a rectangle. 
•Do not install the screen in bright surroundings. If the screen is too bright, the picture on the screen will not be displayed 
clearly.
•When installing the screen in bright surroundings, use curtains.
•You can install the projector in the following locations: Front-Floor / Front-Ceiling / Rear-Floor / Rear-Ceiling.(To view the 
installation position settings) 
 
To view the picture when installing the projector behind the screen
To view the picture when installing the projector in the front of the screen
2-2-2 Leveling with Adjustable Feet 
 You may adjust the level of the projector up to 3 degrees.
Depending on the position of the projector, Keystone distortion of the image may appear. 
 
Install a semi-transparent screen.
1.Select Menu > Setup > Install > Rear-Floor 
2.Select Menu > Setup > Install > Rear-Ceiling  
Install the projector at the side where you are watching the 
screen.
1.Select Menu > Setup > Install > Front-Floor 
2.Select Menu > Setup > Install > Front-Ceiling  
For level placement of the projector, adjust the Adjustable Feet of 
the projector.  
						

							2-2-3Installation and Connection  
2-2-3 Zoom and Focus Adjustment 
 If your product is installed at a location out of the specified projection distance (refer to Screen Size and Projection 
Distance), the focus cannot be adjusted correctly.
 
2-2-4 Screen Size and Projection Distance 
Install the projector on a flat, even surface and level the projector using the adjustable feet to realize optimal picture quality.
If images are not clear, adjust them using the Focus Ring, or move the projector forward and backward. 
 Screen /   Projection Lens /  Projection Optical axis 
A. Screen width / B. Screen height / C. Screen Diagonal length / D. Projection range
1.The screen height and diagonal length according to the projection distance 
 Focus RingFocus the picture on the screen using the Focus Ring.
SCREEN SIZEProjection 
Range(D)Screen width(A)SCREEN 
HEIGHT(B)SCREEN 
DIAGONAL 
LENGTH(C)
20”834mm / 
32.8inches406mm / 16.0 
inches305mm / 12.0 
inches508mm / 20.0 
inches
30”1257mm / 49.5 
inches610mm / 24.0 
inches457mm / 18.0 
inches762mm /30.0 
inches
40”1680mm / 66.1 
inches813mm / 32.0 
inches610mm / 24.0 
inches1016mm / 40.0 
inches
50”2107mm / 83.0 
inches1016mm / 40.0 
inches762mm / 30.0 
inches1016mm / 40.0 
inches
60”2533mm / 99.7 
inches1219mm / 48.0 
inches914mm / 36.0 
inches1524mm / 60.0 
inches 
						

							Installation and Connection2-3-1
  The projection distance is the horizontal distance between the projector and the screen. 
2.When your U300 projector is installed in a location where the projection distance matches the screen diagonal length, you will 
enjoy a clear screen with no distortions (keystone). 
2-3-1 Connecting with a PC 
1.Connect [PC IN] port on the rear side of the projector to the monitor output port of the PC using a PC video cable.
2.When connections are all completed, connect both power cords of the projector and the PC.
3.Connect the [VIDEO/PC AUDIO IN] input port of the projector to the speaker output ports of the PC using an audio cable. 
 This product supports plug and play and therefore, if you use Windows XP, you do not need to setup the driver on your PC. 
Using the Projector 
1.Turn on the projector and press the [SOURCE] button to select .
If the  Mode is not available, make sure the PC video cable is properly connected. 
2.Turn on the PC and set the PC Environment when necessary. 
3.Adjust the screen.(Auto Adjustment)
2-3-2 Setting up the PC Environment 
Check the following items before connecting your PC to your projector. 
70”2959mm / 116.5 
inches1422mm / 56.0 
inches1067mm / 42.0 
inches1778mm / 70.0 
inches
80”3386mm / 133.3 
inches1626mm / 64.0 
inches1219mm / 48.0 
inches2032mm / 80.0 
inches
90”3812mm / 150.0 
inches1829mm / 72.0 
inches1372mm / 54.0 
inches2286mm / 90.0 
inches
100”4238mm / 166.9 
inches2032mm / 80.0 
inches1524mm / 60.0 
inches2540mm / 100.0 
inches
SCREEN SIZEProjection 
Range(D)Screen width(A)SCREEN 
HEIGHT(B)SCREEN 
DIAGONAL 
LENGTH(C) 
						

							2-3-2Installation and Connection  
1.Click the right mouse button on the Windows desktop and click on [Properties]. 
 tab will appear.
2.Click on [Settings] tab and set the  by referring to  described in the display mode table 
supported by this projector.
You do not have to change the  setup. 
3.Press the [Advanced] button. Another property window will appear.
4.Click on [Monitor] tab and set the  by referring to  described in the Supported 
Resolution/Size Modes table. 
This will set both the vertical and horizontal frequencies.
5.Click the [OK] button to close the window, and click the [OK] button of the  window to close the window. 
The computer may restart automatically. 
6.Shut down the PC and connect to the projector.
 •Process might vary depending on your type of computer or Windows version. 
(For example, [Properties] appears instead of [Properties (R)] as shown in 1.) 
						

							Installation and Connection2-3-2
•This appliance supports up to 32 bits per pixel in Color quality when it is used as a PC monitor.
•Projected images may differ from the monitor depending on the monitor manufacturer or Windows versions.
•When connecting the projector to a PC, check that the PC setup complies to display settings supported by this projector. If 
not, there may be signal problems.
  
						

							2-3-3Installation and Connection  
2-3-3Supported Display Modes
 The optimum resolution is 800 x 600, which is the panel resolution. (If inputted signals are different from the optimal 
resolution, the images may appear distorted.) 
 
2-4 Connecting the Power
Rear of Projector 
1.Connect the adapter to the power port. 
2.Connect the power cord to the adapter and connect it to a wall outlet. 
3.When the power is connected, the screen turns on automatically. Do not look at the lens while connecting the power.
 Use only an Samsung authorized adapter.  
RESOLUTION
HORIZONTAL 
FREQUENCY 
(KHZ)VERTICAL 
FREQUENCY 
(HZ)CLOCK 
FREQUENCY(MH
Z)
POLARITY 
IBM, 640 x 480 31.469 59.940 25.175 -/-
IBM, 720 x 400 31.469 70.087 28.322 -/+
MAC, 640 x 480 35.000 66.667 30.240 -/-
MAC, 832 x 624 49.726 74.551 57.284 -/-
VESA, 640 x 480 37.861 72.809 31.500 -/-
VESA, 640 x 480 37.500 75.000 31.500 -/-
VESA, 640 x 480 43.269 85.008 36.000 -/-
VESA, 800 x 600 35.156 56.250 36.000 +/+
VESA, 800 x 600 37.879 60.317 40.000 +/+
VESA, 800 x 600 48.077 72.188 50.000 +/+
VESA, 800 x 600 46.875 75.000 49.500 +/+
VESA, 800 x 600 53.674 85.061 56.250 +/+
VESA, 1024 x 768 48.363 60.004 65.000 -/-
VESA, 1024 x 768 56.476 70.069 75.000 -/-
VESA, 1024 x 768 60.023 75.029 78.750 +/+
VESA, 1024 x 768 68.677 84.997 94.500 +/+ 
						

							Installation and Connection2-5
2-5 Connecting an A/V device with an audio/video cable 
1.Connect [VIDEO IN(yellow)] input port of the projector to the VIDEO (yellow) OUT port of the video equipment using a video 
cable. 
Connect the [L-AUDIO-R] input port of the projector to the Audio (L), Audio (R) output ports of the external device, such as a 
DVD, VCR or camcorder using an audio cable.
2.When the connections are all completed, connect both power cords of the projector and the DVD, VCR, or camcorder. 
Using the Projector 
1.Turn on the projector, press the [SOURCE] button to select the external device (DVD, VCR or camcorder) that is connected. 
2.If the corresponding mode is not selected, check whether the video cable is connected correctly.
 • Check that the projector and the video equipment are turned off before connecting cables.
• The  mode brightness is lower than  and  mode.
 
2-6Connecting an A/V device with a Component/D-Sub Cable 
1.Connect [PC IN] input port on the rear of the projector to the COMPONENT port of AV equipment using a D-Sub/Component 
cable(Not supplied).
2.Connect audio cable(Not supplied) to the audio input port on the rear of the projector.  
						

							2-7Installation and Connection  
2-7 Connecting a USB Device 
Connect your USB device to the USB port at the back of the projector to play videos, photos, and music. 
 Available file system: FAT, FAT32(NTFS is not supported.)
Multi Partition is not supported.
Multi Reader device is not supported.
 
2-8 Connecting Headphones
Connect the jack of the headphones to the input terminal [ ] on the back of the projector.
2-9 Kensington Lock 
Kensington Lock
A Kensington Lock 
(not supplied) is an anti-theft device that enables users to lock the product so that they can safely use it 
in public locations. Since the shape and usage of the locking device may differ depending on the model and the 
manufacturer, for more information, refer to the User Manual 
supplied with the locking device. 
Locking the product
1.Insert the locking part of the locking device into the hole of the Kensington lock of the product and turn it in the locking 
direction. 
2.Connect the Kensington Lock cable.
3.Tie the Kensington lock cable to a desk or heavy object.
 You can purchase the locking device from an electronics store or an online shop.  
						

							Using3-1
3Using
3-1 Product Features 
• High Mobility Design 
•Small Size. 
•Lightweight.
•Play 
videos, photos, music using a USB device. 
3-2 Front, Upper
 NAMEDESCRIPTION
1.Indicators- STAND BY (Blue LED) 
- LAMP (Blue LED)
- TEMP (Red LED) 
 Refer to the LED Indications. 
2. Move   / Select   /
Volume  button  /  : Use this button to move to or select an item within a menu. 
 : Use this button to adjust the volume.
 3. MENU Button Used to display the Menu Screen.
4. SOURCE Button Use this button to select the external device signal. 
5.  Button Used to turn the projector on or off.  
						

							3-2Using
 •When using a tripod, make sure to use one with a screw length of 5.5 mm or less. 
If the screw length is longer than 5.5 mm, you will not be able to fix the projector to the tripod firmly, which may result in 
damage to the projector or tripod. 
•If you use screws to hold the tripod, be sure to use Machine screws M1/4 inch or smaller. 
 
6. Focus Ring Used for Focus Adjustment. 
7. Lens-
8-1. Adjustable Feet You can adjust the screen position by moving the adjustable feet up and down. 
8-2. Tripod holes-
 NAMEDESCRIPTION