Samsung SP-R4212 Plasma Television User Manual

							11
Remote Control Buttons
ŒPOWER button
Turns the TV on and off.
´GUIDE button
Press to display the on-screen Electronic Program Guide (EPG).
ˇANTENNA button
Press to select “Air” or “Cable”.
¨Number buttons
ˆ
-button
Press to select additional channels (digital and analog)
being broadcast by the same station. For example, to select channel
“54-3”, press “54”, then press “
-” and “3”.
ØMUTE button
Press to mute the TV sound.
∏VOL (Volume) buttons
Use it to adjust volume.
”Anynet button
Runs the Anynet view functions and sets up Anynet devices.
’MENU button
Displays the main on-screen menu.
˝ENTER button
Confirms a selection. 
ÔFAV.CH button
Press to switch to your favorite channels.
CH LIST button
Displays the channel list.
ÒMODE button
Selects a target device to be controlled by the Samsung remote control
(i.e., TV, STB, VCR, CABLE, or DVD).
ÚPRE-CH button
Tunes to the previous channel.
ÆSOURCE button
Press to display all of the available video sources (TV, AV, S-Video, 
Component1, Component2, PC, and HDMI).
ıCH (Channel) buttons
Use it to switch channels.
˜INFO button
Press to display information on the TV screen.
¯EXIT button 
Press to exit the menu.
˘Up/Down/Left/Right buttons
Control the cursor in the menu.                   Continued...
Remote Control
BN68-00835D-00Eng_(002~031)  4/15/05  11:21 AM  Page 11 
						

							¿P.MODE buttonAdjust the TV picture by selecting one of the preset factory settings (or
select your personal, customized picture settings).
¸S.MODE buttonSelect Sound effect.
˛E.SAVING buttonPress to adjust screen brightness according to surrounding environment.
(Refer to page 111)
◊P.SIZE buttonSelect Picture size.
±DNIe buttonActivates DNIe Demo. (Refer to page 51)
≠MTS buttonPress to choose stereo, mono or Separate Audio Program 
(SAP broadcast).
–SET buttonUsed during set up of this Samsung remote control, so that it will work
compatibly with other devices (VCR, Cable Box and DVD). 
—PIP buttonActivates picture in picture.
÷PIP control buttonsCH,: Displays the available channels in sequence. 
(These buttons change channels in the PIP window only.)
®CAPTION buttonControls the caption decoder.
∑VCR, DVD control buttonsControls VCR tape or DVD disc functions: Stop, Rewind, Play/Pause,
and Fast Forward.
µRESET button If your remote control is not functioning properly, take out the batteries
and press the reset button for about 2~3 seconds. 
Re-insert the batteries and try using the remote control again. 
12
Installing the Batteries in Your Remote Control
1Slide the back cover to
open the battery
compartment of the remote
control
.
3Slide the cover back into
place.2Install two AAA size
batteries. Make sure to
match the “+” and “-” ends
of the batteries with the
diagram inside the
compartment.
Remote Control Operation Range
You can use your remote control within a distance of 23 feet and an angle of 30 degrees
from the left and right sides of the TV’s remote control receiver.
BN68-00835D-00Eng_(002~031)  4/19/05  5:56 PM  Page 12 
						

							13
Wall Installation Instructions
Refer to the correct installation guide according to your wall bracket.
1
Contact a technician for installing the wall bracket.
2
Samsung Electronics is not responsible for any damage to the product or injury to yourself
or others if you elect to perform the wall installation.
3
This product is for installing on cement walls. The product may not stay in place when
installed on plaster or wood.
Installation Notes
Parts (Wall attachment panel is sold separately. Check with your dealer.)
Only use the components and accessories shipped with the panel.
Plastic Hanger : 4Screw : 11
Screw : 4Anchor : 11 1Left : 1 Right : 1
Wall Bracket Hinge Accessories
BN68-00835D-00Eng_(002~031)  4/15/05  11:21 AM  Page 13 
						

							14
1 
Insert and tighten the Captive Screw in the direction of the arrow.
When done, mount the wall bracket on the wall.
2
Before drilling into the wall, check if the
length between the two locking holes at 
the back of the product is correct. If the 
length is too short or long, loosen all or 
some of the 4 screws on the wall 
bracket to adjust the length.
How to assemble the Wall Mount Bracket
3
Check the installation diagram and
mark the drill points on the wall. 
Use the 5.0 mm bit to drill holes deeper
than 35 mm. Fix each anchor in the 
corresponding hole. Match each of the 
brackets and hinge holes to the 
corresponding anchor holes and insert 
and tighten the 11 screws .
Captive Screw
Wall Bracket
Hinge (Right) There are two hinges
(left and right). Use the 
correct one. Hinge (Left)
Length between the
two locking holes
BN68-00835D-00Eng_(002~031)  4/15/05  11:21 AM  Page 14 
						

							15
1 
Remove the 4 screws on the back of the product.
2 
Insert the screw into the plastic hanger. (See the figure below)
Fixing the TV panel to the wall attachment panel bracket
The shape of the product may vary depending on the model. (The assemblies of the plastic
hanger and the screw are the same)
3
Tighten the 4 screws in step 2 (plastic
hanger + screw ) to the rear holes of 
the product.
4
Remove safety pin (#) and insert the 4
product holders into the corresponding 
bracket holes (!). Then place the 
product (@) so that it is firmly fixed to 
the bracket. Make sure to reinsert and 
tighten the safety pin (#) to securely 
hold the product to the bracket.
PDP
Wall Bracket Wall
• Mount the product on the wall bracket and make sure it is properly fixed to the left and 
right plastic hangers.
• Be careful when installing the product on the bracket as fingers can be caught in the holes.
• Make sure the wall bracket is securely fixed to the wall, or the product may not stay in 
place after installation.
BN68-00835D-00Eng_(002~031)  4/15/05  11:21 AM  Page 15 
						

							16
How to Adjust Mounting Angle
Note  Note : Adjust the bracket angle to -2° before installing it on the wall.
Make sure to use the top center,
and not the left or the right side of
the product to adjust the angle.1. Fix the product to the wall bracket.
2. Hold the product at the top in the center and pull it 
forward (direction of the arrow) to adjust the angle. 
(See the figure to the right)
3. You can adjust the bracket angle between 
-2° and 15°.
BN68-00835D-00Eng_(002~031)  4/26/05  2:32 PM  Page 16 
						

							17
How to assemble the Stand-Base
➤ ➤Two or more people should carry the TV. Never lay the TV on the floor because of possible damage to the screen. 
Always store the TV upright.
1
Using the 4 screws for securing the stand pegs and the monitor, firmly attach the monitor
to the stand pegs. (The exterior of the set may be different than the picture.) 
Warning
Firmly secure the stand to
the TV before moving it, 
as the stand may fall and 
could cause serious injury.
BN68-00835D-00Eng_(002~031)  4/15/05  11:21 AM  Page 17 
						

							BN68-00835D-00Eng_(002~031)  4/15/05  11:21 AM  Page 18 
						

							PLASMA DISPLAY PANEL
Connections
Connecting VHF and UHF Antennas ..............................................20
Connecting Cable TV....................................................................21
Connecting a VCR........................................................................23
Connecting a Camcorder ..............................................................24
Connecting a DVD Player (480i, 480p) ..........................................25
Connecting a DTV Receiver (480p, 720p, 1080i) ..........................26
Connecting to HDMI (High Definition Multimedia Interface) 
(480p, 720p, 1080i) ..................................................................27
Connecting a Digital TV Set-Top Box (480p, 720p, 1080i) ..............28
Connecting a Digital Audio System ................................................29
Connecting to an Analog Amplifier ................................................30
BN68-00835D-00Eng_(002~031)  4/15/05  11:21 AM  Page 19 
						

							Connecting VHF and UHF Antennas
20
Antennas with 75-ohm Round Leads
If your antenna looks like this: it has 75-ohm round leads.  
1
Plug the antenna lead into the ANT 2 IN (AIR IN) 
on the TV.
Use an antenna cable. (Sold Separately)
BN68-00835D-00Eng_(002~031)  4/19/05  5:56 PM  Page 20