Samsung Sp P310me User Manual

   
 
 
|  Product Features | Product Views | Battery (sold separately) | Product Specifications | 
 
 
 
 
 
 Your Battery  
 
 
         
1. Locking hole  
  
     Locks the battery t o the projector. 
  
2. Power Terminal  
  
     Connect the power cord here  to charge the battery. 
  
3. Battery Latch  
  
     The battery latch is used to hold the battery in place when con nected to the main body. 
  
4. Battery Charge Indicator  
Shows the remaining battery charge.  
  
  
While charging the...

 
LED lights up red. 
  
This displays the remaining ba ttery power in a percentage.  
To check the remaining battery power, press the  PUSH button at 
the bottom right of the battery pack. The remaining battery lif e is 
indicated with the blue lamp and the blue lamp turns off after 
about five (5) seconds.
  
When the AC power is connected through the adapter, the blue 
LED lights up if charging is completed.
    
 Battery Installation and Precautions.   
   
  1. Installing the Battery  
 
Place the...

 
Hold the back of the projector and lift it up while sliding the latch on the back of the battery to the left ( ).
   
   
  3. Battery Use Time  
zOperating time : Up to 2.5 hours when fully charged  
zCharge time : About 3 hours when charging separately from the p rojector 
   
   
  4. Charging the Battery  
  Charging the battery when the battery is separated from the projector. 
zAdapter Standard : DC 14 V, 3.5 A 
   
   
  Charging the battery when the  battery is installed under the projector....

Using a non-designated battery may damage the projector.
Avoid heat or impact to the battery.   
Avoid strong force/impact to the  battery, such as dropping or throwing the battery. Avoid exposing 
the battery to high temperatures  such as a sauna. This may generate heat or cause fire or the 
battery to explode. If the battery  generates heat or fire, is damaged or deformed, immediately 
remove the battery from the projector, and isolate the battery  in a safe location as it may generate 
heat or cause...

 
Voltage   DC 14 V, 3.5 A  
Dimension   127.2 mm x 94.5 mm x  50.8 mm (5 inches x 3.7 inches x 2 inches) 
Weight   700 g (1.54 lb) 
Major 
Functions   Brightness   50 ANSI lm  
Contrast   1000:1  
Screen Size   Diagonal 15" ~ 60"  
Projection 
Distance  
0.5~2.8 m  
Keystone   Vertical  
Input/Output  
(24Pin)   PC  
1) Connector Type : 15Pin D-Sub  
2) Frequency (Refer to the 
Supported Display Modes.)  
Composite   Supported Broadcast Signal
s : NTSC, PAL, SECAM 
(PAL-60 is not supported.)...

SVGA, 832 x 624  49.726 74.551 57.284 +/+XGA, 1024 x 768 35.522 43.479 44.900 +/+
XGA, 1024 x 768 48.636 60.004 65.000 -/-
XGA, 1024 x 768 56.476 70.069 75.000 -/-
XGA, 1024 x 768 60.023 75.029 78.750 +/+
XGA, 1024 x 768 68.677 84.997 94.500 +/+
XGA, 1024 x 768 48.78 60.001 64.000 -/-
XGA, 1024 x 768 60.241 74.927 80.000 -/-
  
  
The DMD Panel used in Samsung Pr ojectors consists of several hundred thousand micro mirrors. As with other 
visual display elements, the DMD Panel may include a few bad pi...

 
 
 |  Basic Settings | Connecting the Power | Connecting to a PC | Connecting to an AV device | 
 
 
 
 
 Installing the Projector
 
  Install the projector so that the beam from the projector is p erpendicular to the screen.  
  
Place the projector so that the l ens is at the center of the screen. 
  If the screen is not vertically installed, the picture on the  screen may not be a rectangle. 
Do not install the screen in bright surroundings. If the screen  is too bright, the picture on the screen...

 
 
 
  Screen Size and Projection Distance   
 
 
Distance   Picture size 
Diagonal (inch)  
m ft mm x mm inch x inch
0.5 1.64 25.5 x 19.1 1.0 x 0.75 12.5
1.0 3.28 50.8 x 38.1 2.0 x 1.5 25.0
1.64 5.38 83.3 x 62.5 3.28 x 2.46 41.0 2.0 6.56 101.6 x 76.2 4.0 x 3.0 50.0
2.8 9.18 127.0 x 95.3 5.0 x 3.75 63.0
 
 
 
 |  Basic Settings | Connecting the Power | Connecting to a PC | Connecting to an AV device | 
 
 
 
 
 
  
 
  
 
Connect the adapter to the power port( ). 
Connect the power cord to the adapter...

 
 
 
 |  Basic Settings | Connecting the Power | Connecting to a PC | Connecting to an AV device | 
 
 
 
  
 
  
 
 
Connect the [PC/COMPOSITE] port on the side of the projector to  the Monitor OUT port [D-Sub] of your PC using a 
PC/Composite cable. 
When all the connections above have been connected, turn the pr ojector and the PC on.  
    Using the Projector   
  Selecting the external input source.  
Select PC input by pressing the SOURCE button.  ( SOURCE ) 
Select PC input by pressing the Menu...

  
 
 
Connect a PC/Composite cable to the [PC/COMPOSITE] port on the side of the projector and then connect the 
[COMPOSITE Input (Yellow)] connector of the PC/Composite cable  to the VIDEO OUT (Yellow) port of the AV device 
using a video cable. 
When all the connections above have been completed, turn the pr ojector and video devices on. 
    How to Use   
  Selecting the external input source.  
Press the SOURCE button and select the Composite input  ( SOURCE )
Select the Composite input using the...