Samsung Sp L220 User Manual

							 
 
 
 
 
 
Action 4 This indicates that it has changed 
to Cooling mode, because the 
internal temperature of the 
projector has increased beyond 
the maintenance limit.   automatically.  
* Cooling mode: The fan speed has increased and the projector lamp 
has been changed to ECO mode. 
Check whether the ventilating hole of the projector is blocked.  
Check the air filter and clean if blocked.
 
Check whether the surrounding temperature of the projector is higher 
than the standard temperature range of the projector. 
Cool the projector sufficiently  and operate it again. 
Action 5  If the internal temperature of the 
projector increases higher than 
the limit, it is turned off 
automatically.  Check whether the ventilating hole of the projector is blocked.  
Check the air filter and clean if blocked.
 
Check wh

ether the surrounding temperature of the projector is higher 
than the standard temperature range of the projector. 
Cool the projector sufficiently  and operate it again. 
If the same problem occurs continually,  contact your product distributor or 
service center .  
Action 6  The lamp 
malfunctions after power 
turns off 
abnormally or after 
powering on right after 
turning off the projector. Turn the power off, wait for a sufficient amount of cooling time and then 
turn the power on to operate. If the same problem occurs continually, 
contact your product distributor or 
service center. 
This Projector uses a cooling fan system to keep the  unit from overheating. Operation of the cooling fan 
may cause noise, which does not affect the produc t performance and is part of normal operation. 
 
 
 
  Rear Side 
 
  
1. PC OUT port  
  
2. AUDIO OUT port  
  
3. RS-232C port (For service input 
terminals) 
  
4. [AV IN] R-AUDIO-L Input port  
  
5. [AV IN] VIDEO Input port  
  
6. [AV IN] S-VIDEO Input port 
  
7. [PC IN1,2] PC Input port  
  
8. [PC IN1,2] AUDIO Input port 
  
9. Remote Control Signal Receiver 
 
10.POWER Input port 
 
Downloaded From projector-manual.com Samsung Manuals 
						

							 
 
 
 
  
 
 
 |  Product Features | 
Product Views | 
Remote Control | 
Product Specifications | 
 
 
 
 
 
 
1.
POWER ( ) Button
2.AUTO Button
3. MENU ( ) Button
4.Move (▲  ▼  ◀  ▶)/( ) Button
5. V.KEYSTONE(+/-)  
(VERTICAL KEYSTONE)Button
6. INSTALL Button
7. BLANK Button
8. P.SIZE Button 
9. QUICK utton
10. MUTE ( ) Button
11.RETURN ( ) Button
12.EXIT ( ) Button
13.VOL Button
14. INFO Button
15. SOURCE Button
16. P.MODE Button
17. STILL Button
  
1. POWER ( )  
Used to turn on the projector. 
 
2. AUTO 
Adjusts the Picture automatically. (Available in PC Mode Only)  
 
3. MENU ( ) 
Used to display Menu Screen.  
 
4. Move (▲  ▼  ◀  ▶)/ ( ) 
Used to move to or se lect each menu item.  
 
5.
V.KEYSTONE(VERTICAL KEYSTONE) (+/-) 
Use this when video scenes are distorted or tilted.  
 
6. INSTALL  Used to flip or reverse the projected image. 
 
7. BLANK   This is used to turn off the  video 
 and audio temporarily. 
The video and audio will come back on when any button other than the POW\
ER button is pressed.   
 
8.

P.SIZE 
Used to adjust 
the size of the picture screen .  
Downloaded From projector-manual.com Samsung Manuals 
						

							  
9. QUICK   This is used to quickly return to the last menu used. 
10. MUT

E ( ) 
This is used to temporarily mute the sound. 
 
T o hear sound again, press the MUTE button again or press the - VOL + button.  
 
11. RETURN ( ) 
Returns to the pr evious menu.  
 
12. EXIT ( ) 
Used to make Menu Screen disappear.  
 
13. VOL  
Adjusts the volume.  
 
14. INFO   Used to check source signals, picture setup,  PC screen adjustment and lamp lifespan.  
 
15. SOURCE  
This is used to switch between  the TV and the external input. 
 
16. P.MODE   Used to select Picture Mode. 
 
17. STILL   Used to see still images.  
 
 
 
 
|  Product Features | 
Product Views | 
Remote Control | 
Product Specifications | 
 
 
 
Design and specifications of the product may be modi
fied without prior notice for better performance. 
   Specifications  
 
Model   SP-L250, SP-L220, SP-L200 
Panel 0.63 3P LCD
Resolution XGA (1024 x 768)
Aspect ratio 4:3
Brightness  Max 2,500 ANSI lumen (L250) 
Max 2,200 ANSI lumen (L220) 
Max 2,000 ANSI lumen (L200)
Contrast Max 500:1
Diagonal screen size 40 ~ 300
Projection Range 1 m ~ 10 m
Zoom Adjustment Manual
Focus Adjustment Manual
Lens F=1.65~1.93, f=18.5mm~22.5mm
Zoom Ratio 1:1.2
Keystone Vertical  (±20°)
Lamp  Power 
Consumption 
203W ( Eco : 172W ) 
Life Time 2,500 Hours (Eco : 3,000 Hours ) 
Input Terminal D-Sub 15p x 2 Analog RGB, analog YPbPr 
Mini DIN x 1 S-Video
Downloaded From projector-manual.com Samsung Manuals 
						

							 
RCA x 1  Composite video 
Speaker  3W x 2 (Stereo) 
Power  Power 
Consumption 
Max 280 W 
Voltage  100~240V AC, 50/60Hz 
Noise   Eco : 30dB, Bright : 32dB
Dimensions   291(W) x 289(D) x 127(H) 
11.5 inches(W) x 11.4 inches(D) x 5 inches(H)  
Weight   3.8 Kg / 8.4 lb 
User 
Environment   Operating 
Temperature : 41 °F ~ 95 °F (5 °C ~ 35 °C), 
Humidity : 20 % ~ 80 % ((Non-condensing)) 
Storage Temperature : -14 °F ~ 140 °F (-10 °C ~ 60 °C) 
Humidity : 10 % ~ 90 % (Non-condensing) 
This Class B equipment is designed for home and office use. The equipment has been registered 
regarding EMI for residential use. It may be used in 
all areas. Class A is for office use. Class A is for 
business while class B emits less electromagnetic waves than class A. 
 
The LCD panel used in the LCD projector consists of hundreds of thousands of fine pixels. 
Like other video display devices, the LCD panel ma y contain bad pixels which do not operate. When 
shipping a product, the conditions for identifying bad pixels and the number of bad pixels that a LCD 
panel is allowed to contain are st rictly managed in accordance with the relevant specified standards 
by the LCD panel manufacturer and our company. Though a screen may have some dead pixels, this 
does not affect the overall screen qua lity and the lifetime of the product.  
 
  
 Supported Display Modes  
 
 PC Timing
FormatResolutionHorizontal 
Frequency  (kHz)Vertical 
Frequency  (Hz)Pixel Frequency  (MHz)
IBM 640 x 350 70Hz 31.469 70.086 25.175 
IBM 640 x 480 60Hz 31.469 59.940 25.175 
IBM 720 x 400 70Hz 31.469 70.087 28.322 
VESA 640 x 480 60Hz 31.469 59.940 25.175 
MAC 640 x 480 67Hz 35.000 66.667 30.240 
VESA 640 x 480 70Hz 35.000 70.000 28.560 
VESA 640 x 480 72Hz 37.861 72.809 31.500 
VESA 640 x 480 75Hz 37.500 75.000 31.500 
VESA 720 x 576 60Hz 35.910 59.950 32.750 
VESA 800 x 600 56Hz 35.156 56.250 36.000 
VESA 800 x 600 60Hz 37.879 60.317 40.000 
VESA 800 x 600 70Hz 43.750 70.000 45.500 
VESA 800 x 600 72Hz 48.077 72.188 50.000 
VESA 800 x 600 75Hz 46.875 75.000 49.500 
MAC 832 x 624 75Hz 49.726 74.551 57.284 
VESA 1024 x 768 60Hz 48.363 60.004 65.000 
VESA 1024 x 768 70Hz 56.476 70.069 75.000 
VESA 1024 x 768 72Hz 57.672 72.000 78.434 
VESA 1024 x 768 75Hz 60.023 75.029 78.750 
VESA 1152 x 864 60Hz 53.783 59.959 81.750 
VESA 1152 x 864 70Hz 63.000 70.000 96.768 
VESA 1152 x 864 72Hz 64.872 72.000 99.643 
VESA 1152 x 864 75Hz 67.500 75.000 108.000 
VESA 1280 x 720 60Hz 44.772 59.855 74.500 
VESA 1280 x 720 70Hz 52.500 70.000 89.040 
VESA 1280 x 720 72Hz 54.072 72.000 91.706 
VESA 1280 x 720 75Hz 56.456 74.777 95.750 
VESA 1280 x 768 60Hz 47.776 59.870 79.500 
VESA 1280 x 768 75Hz 60.289 74.893 102.250 
VESA 1280 x 800 60Hz 49.702 59.810 83.500 
VESA 1280 x 800 75Hz 62.795 74.934 106.500 
VESA 1280 x 960 60Hz 60.000 60.000 108.000 
Downloaded From projector-manual.com Samsung Manuals 
						

							 
 
 
 
 
 
VESA 1280 x 960 70Hz 69.930 70.000 120.839 
VESA 1280 x 960 72Hz 72.072 72.000 124.540 
VESA 1280 x 960 75Hz 75.231 74.857 130.000 
VESA 1280 x 1024 60Hz 63.981 60.020 108.000 
VESA 1280 x 1024 70Hz 74.620 70.000 128.943 
VESA 1280 x 1024 72Hz 76.824 72.000 132.752 
VESA 1280 x 1024 75Hz 79.976 75.025 135.000 
VESA 1400 x 1050 60Hz 65.317 59.978 121.750 
VESA 1440 x 900 60Hz 55.935 59.887 106.500 
VESA 1440 x 900 75Hz 70.635 74.984 136.750 
VESA 1600 x 1200 60Hz 75.000 60.000 162.000 
For the resolutions presented above, if a signal with a resolution lower or higher than 1024x768 is 
input, it is converted to 1024x768 by the Scaler chip inside the projector. 
When the real resolution (1024x768) of the projecto r and the PC output resolution are the same, the 
screen quality is optimal. 
 
AV Timing (D-Sub)
FormatResolutionScan
BT.601 SMPTE 267M 480i 59.94Hz Interlaced 
BT.1358 SMPTE 293M 480p 59.94Hz Progressive 
BT.601 576i 50Hz Interlaced 
BT.1358 576p 50Hz Progressive 
SMPTE 296M 720p 59.94Hz/60Hz Progressive 
720p 50Hz Progressive 
BT.709 SMPTE 274M 1080i 59.94Hz/60Hz Interlaced 
1080i 50Hz Interlaced 
  AV Timing (VIDEO/S-VIDEO)
NTSC, NTSC 4.43, PAL, PAL60, PAL-N, PAL-M, SECAM 
 
Downloaded From projector-manual.com Samsung Manuals 
						

							 
 
 |  Basic Settings | 
Connecting the Power | 
Connecting an External Device  | 
 
 
 
 
 Installing the Projector
 
  Install the projector so that the beam from  the projector is perpendicular to the screen.  
  
Place the projector so that the lens is at the center of the screen. 
  If the screen is not vertically installed, th e picture on the screen may not be a rectangle. 
Do not install the screen in bright surroundings. If the screen is too bright, the picture on  the screen will not be displayed 
clearly.
When installing the screen in bright surroundings, use curtains.
You can install the projector in the following locations: Front-Floor / Front-Ceiling / Rear-Floor / Rear-Ceiling. 
( To view the installation position settings ) 
 To view the picture when installing the projector behind the screen, 
 
    Install a semi-transparent screen. 
Select  Menu > Setup > Install > Rear-Floor   
 
 To view the picture when installing the projector in the front of the screen, 
 
   Install the projector at the side where you are watching the 
screen. 
Select  Menu > Setup > Install > Front-Floor  
 
  Zoom and Focus Adjustment 
 
 
 Zoom Knob      Focus Ring
Downloaded From projector-manual.com Samsung Manuals 
						

							 
 
 
 
 
 
 
Y
ou can adjust the size of image within zoom range by manipulating the Zoom 
Kn ob. 
Focus the picture on the sc reen using the Focus Ring.
  
If your product is installed at a location out of the specified projection distance 
(refer to Screen Size and Projection Distance ), the focus cannot be 
adjusted correctly.
 
  Leveling with Adjustable Feet  
 
 
 
  For level placing of the projector, adjust the Adjustable Feet of the projector.
  
The projector can be adjusted to a height of  up to 30 mm (about 12 °) from the reference 
point.
Depending on the position of the projector, Keystone distortion of the image may appear.   
If a 

keystone occurs, adjust it using the  V-Keystone function. 
  Screen Size and Projection Distance  
Install the projector on a flat, even surface and level the proj ector using the adjustable feet to realize optimal picture quality. If images 
are not clear, adjust them using th e Zoom Knob or Focus Ring, or move the projector forward and backward. 
 
Screen size  
(M:inch)   Horizental Vertical  Max  Min  Offset  
(X:mm) (Y:mm) (Z:mm) (Z:mm) (Y:mm) 
40 812.8 609.6 13761140 102 
50 1016.0 762.017271433 127 
60 1219.2 914.420781726 152 
70 1422.4 1066.8 24302020 178 
80 1625.6 1219.2 27812313 203 
90 1828.8 1371.6 31332606 229 
100 2032.0 1524.0 34842899 254 
110 2235.2 1676.4 38353192 279 
120 2438.4 1828.8 41873485 305 
130 2641.6 1981.2 45383778 330 
140 2844.8 2133.6 48894071 356 
150 3048.0 2286.0 52414364 381 
160 3251.2 2438.4 55924657 406 
170 3454.4 2590.8 59444950 432 
180 3657.6 2743.2 62955243 457 
190 3860.8 2895.6 66465536 483 
200 4064.0 3048.0 69985829 508 
210 4267.2 3200.4 73496122 533 
220 4470.4 3352.8 77016415 559 
230 4673.6 3505.2 80526708 584 
240 4876.8 3657.6 84037001 610 
250 5080.0 3810.0 8755 7294635 
Downloaded From projector-manual.com Samsung Manuals 
						

							 
 
 
 
 
 
 
 
260
5283.2 3962.4 9106 7587660 
270 5486.4 4114.8 9457 7880686 
280 5689.6 4267.2 9809 8173711 
290 5892.8 4419.6 10160 8466737 
300 6096.0 4572.0 10512 8759762 
This projector is designed to show images  optimally on a 80 ~ 120 inch sized screen.
 
 
A. Screen 
Z: Throw Distance
Y: Distance from Lens Center to Image Bottom 
  Setting up the PC Environment  - Check the following items before co nnecting your PC to your projector.
 
1. Click the right mouse butto n on the Windows desktop 
and click on [Properties].  
 tab will appear.
2. Click on [Settings] tab and  set the  by 
referring to  
as described in  the display mode table 
su

pported  by this projector. 
You do not have to change  setup.
3. Press the [Advanced] button.  Another property window will appear.
Downloaded From projector-manual.com Samsung Manuals 
						

							 
 
 4. Click on [Monitor] tab and set the 
 by referring 
to  as described in  th
e Supported 
Reso
 lution/Size Modes table
.  
5. Click the [OK] button to cl ose the window, and click the 
[OK] button of the  window to close the 
window. 
The computer may restart automatically.  
 
 
   
6. Shut down the PC and  connect to the projector.
   
   
Process might vary depending on your type of computer or Windows versions.  
(For example, [Properties] appears inst ead of [Properties (R)] as shown in 1.)
This unit appliance supports up to 24 bits per pixel  in Color quality when it is used as a PC monitor.
Projected images may differ from the monitor depe nding on monitor manufacturer or Windows versions.
When connecting the projector to a PC, chec k that PC setup complies to display settings supported by this projector. If not, 
there may be signal problems.
 
 
 |  Basic Settings | 
Connecting the Power | 
Connecting an External Device  | 
 
 
 
  
 
   
1. Rear of Projector 
  
Plug the power cord into the power terminal on the rear side of the projector. 
 
 
 
 |  Basic Settings | 
Connecting the Power | 
Connecting an External Device  | 
 
 
 
Downloaded From projector-manual.com Samsung Manuals 
						

							 
 
Connecting a PC using a D-Sub cable 
 
 
 
 
 
Check that your PC and projector are turned off. 
Connect the [PC IN (1 or 2) PC ] terminal at the back of the projector to the  D-Sub terminal of your PC using a D-Sub cable.
  - For the supported input signals, refer to  PC Timing.  
Connect the [PC IN (1 or 2) AUDIO] terminal at the back of th e projector to the Audio out terminal of your PC using an audio 
cable (Not supplied).
   Connecting an External Monitor 
 
 
 
 
 
You can view an image on both your projecto r and a separate monitor at the same time. 
 
Check that your PC and projector are turned off.
Connect the [PC IN (1) PC]  terminal at the back of the projector to the D- Sub terminal of your PC using a D-Sub cable. 
Connect the [PC OUT] terminal of the projector to th e D-Sub terminal of a monitor using a D-Sub cable. 
  - When connecting a monitor using the [PC OU T] function, make sure to connect your PC to the [PC IN (1
) PC] terminal.  
 

- The monitor output which is connected to the [PC OUT] terminal will be normal even  if 
you see a blank screen on 
   y

our projector. 
Downloaded From projector-manual.com Samsung Manuals