Samsung Sp A600b User Manual

							Using3-5
3-5-4. Option
MENUDESCRIPTION
Language You can select the language used for the menu screen.
Menu Position You can move Menu Position up/down/left/right.
Menu Transparency You can set the transparency of menu.
• -  -  -  
Menu Display Time You can set the display time of the menu.
•  -  -  -  -  -  -  
Auto Power On If the power is supplied to the projector, it is turned on automatically without pressing the Power but-
ton.
•  -  
Sleep Timer If there is no input signal for the specified time, the projector is turned off automatically.
(There must be no button input from the remote control or on the top of the projector for the specified 
time.) 
•  -  -  -  
LED Indicator You can turn the LED indicators on your projector on or off according to your requirements.
•  : This mode disables the operating LED. However, the LED will come on regardless of the 
LED setting when the power is turned on or off or when the projector is in an abnormal state.
•  : This mode enables the operating LED so that it can display the current operating state of 
the projector. 
Buzz You can turn on or off the sound when pressing one of the buttons on your projector.
•  -  
Information You can check external source signals, picture setup, PC picture adjustment. 
Downloaded From projector-manual.com Samsung Manuals 
						

							4-1Troubleshooting
4 Troubleshooting
4-1 Before Requesting Service
 Please check the following before requesting After-Sales service. If the problem continues, please contact your nearest 
Samsung Electronics Service Center.
 
Symptoms Troubleshooting
Installation 
and Con-
nection No Power. Check the power cable connections. 
I want to install my projector on the ceiling.  The ceiling installation support is sold separately. Contact your 
local product distributor. 
External Source can not be selected. Be sure that the connection cable(s) is properly connected to 
the proper port. If the device is not connected properly, it can 
not be selected.
Menu and 
Remote 
Control Remote control does not work. Be sure that the proper external source is selected. 
Check the remote control battery. If there is something wrong 
with it, replace it with a new battery of the recommended size. 
Be sure to aim the remote at sensor on the front or back of the 
unit and at a distance of no more than approximately 23 feet(7 
m). Remove any obstacles between your remote control and 
the product.
Direct light from 3-way light bulbs or other lighting devices on 
the remote sensor of the projector may affect the sensitivity 
and cause the remote control to malfunction. 
Check if the remote control battery compartment is empty. 
Check whether the LED indicator on the top of the projector is 
turned on.
I cannot select a menu. Check if the menu is displayed in gray. A gray-colored menu is 
unavailable.
Downloaded From projector-manual.com Samsung Manuals 
						

							Troubleshooting4-1
Screen and 
External 
Source Cannot see picture images. Be sure that the power cord of the projector is connected.
Be sure that the proper input source is selected.
Check that the connectors are properly connected to the ports 
at the back of the projector.
Check the Remote Control batteries.
Be sure that the ,  settings are not at their 
lower limit.
Poor color.  Adjust the  and . 
Images are not clear. Adjust the focus. 
Check that the projection distance is either too far or too near 
to the screen.
Strange noise. If a strange sound continues, contact our Service Center. 
The operating LED is lit up. Refer to Corrective Actions According to LED Indications. 
Lines appear on screen. Because noise may occur when using your PC, adjust the fre-
quency of the screen.
No external device screen is displayed. Check the operating status for the external device and check 
whether the adjustment items, such as the Brightness and the 
Contrast have been changed correctly in the  com-
mand screen of the Projector menu. 
Only blue screen appears. Be sure to properly connect the external devices. Check the 
connection cables again.
Screen appears in black and white or odd 
color./ screen is too dark or bright.As mentioned above, check the adjustment items such as the 
,  and  in the menu. 
Check  in the OSD menus.
If you want to restore various settings to their factory defaults, 
run from the menu. 
Symptoms Troubleshooting
Downloaded From projector-manual.com Samsung Manuals 
						

							5-1More Information 
5More Information
5-1 Specifications
 This Class B equipment is designed for home and office use. The equipment has been registered regarding EMI for 
residential use. It may be used in all areas. Class A is for office use. Class A is for business while class B emits less 
electromagnetic waves than class A.
  The DMD Panel used in DLP Projectors consists of several hundred thousand micro mirrors. As with other visual display 
elements, the DMD Panel may include a few bad pixels. Samsung and the DMD Panel manufacturer have a rigid, bad pixel 
identification and limitation procedure in place and products will not exceed the maximum number of bad pixels set by our 
standards. Rarely, non-displayable pixels may exist, however it does not affect the picture quality nor the lifespan of the 
product.
 
MODEL SP-A600B
PanelSize 16.5 mm / 0.65 inches
Resolution FHD (1920x1080)
Manufacturer Texas Instrument
LampType 220 W UHP (Theater mode : 187 W)
Life Time 3,000 Hours
Manufacturer Philips
Color 62.2 M (1920 x 1080 x 3 x 10bit)
ResolutionOptimum resolution 1920 x 1080 @ 60 Hz
Maximum resolution 1920 x 1200 @ 60 Hz (Reduce Blanking)
Input video signal Video, S-Video, Component, Analog PC, 2 x HDMI
Input synchronization signal Separate H/V sync
Maximum Pixel Clock 162 MHz
Diagonal screen size 1016 ~7620 mm (40 ~ 300 inches)
Projection Range 1.3 m ~ 13 m (53.3 ~ 520.3 inches)
Power Power Consumption  Less than 275 W
Voltage  110/220 Vac +/-10 %, 50/60 Hz +/-3 Hz
Noise
24dB(Theater)
Dimensions 343.1 mm(W) x 162.4 mm(H) x 347.2 mm(D) / 13.5 inches(W) x 6.4 
inches(D) x 13.7 inches(H) 
Weight 4.7 kg / 10.4 lbs
Key Features Brightness 1000 ANSI
Contrast 3000:1
Keystone Vertical
User Environ-
ment Temperature and Humidity  Operating: Temperature 32 °F ~ 104 °F (0 °C ~ 40 °C), 
Humidity (10 % ~ 80 %)
Storage : Temperature -4 °F ~ 113 °F (-20 °C ~ 45 °C) , 
Humidity (5 % ~ 95 %)
Downloaded From projector-manual.com Samsung Manuals 
						

							More Information5-2
5-2 RS-232C Command Table
Communication Format (Complies with the RS232C Standard)
• Baud rate : 9,600 bps 
• parity : None
• Data bits : 8, stop bit : 1
• Flow Control : None
Serial Communication Protocol
1.Command Packet Structure [7bytes]
• A command packet consists of 7 bytes in total.
• The two bytes 0x08 and 0x22 signify that the packet is for serial communication.
• The following 4 bytes represent a pre-defined command that can be defined by the user.
• The last byte is the checksum which checks the validity of the current packet.
• Header [2 Byte]: Pre-defined values fixed to 0x08 and 0x22.
• Cmd1 [1 Byte]: The first value of the code defined in the command list (Hexadecimal)
• Cmd2 [1 Byte]: The second value of the code defined in the command list (Hexadecimal)
• Cmd3 [1 Byte]: The third value of the code defined in the command list (Hexadecimal)
• Value [1 Byte]: Input parameter for the command (Default: 0) (Hexadecimal)
• CS [1 Byte]: Checksum (the 2’s complement of the sum of all the values except for the CS value.)
2.Response Packet Structure [3 Bytes]
1.Success
2.Fail
• When the received packet from an external device has a valid value, a Success packet is sent. Otherwise, a Fail 
packet is sent.
• A Fail packet is sent if:
•The received packet length is not equal to 7 bytes.
•The 2 byte packet header value is not equal to 0x08, 0x22.
•The check sum is incorrect.
• Failure detection by an external device
•An external device classifies the packet as Fail if it does not receive a Success packet within 100ms.
 •Transmit the following control command to transmit one or more control commands if there was a successful response 
for the previous transmission or there was no response in over 3 seconds.
• While controlling the Projector using a Computer, you cannot check the Projector’s status change using the Computer nor will it 
be displayed on the Projectors screen. Transmit the INFORMATION command to display the current information on the 
Projectors screen.
• All the control commands apply to the input source and the Projectors status currently displayed.
 
0x08
0x22 cmd1 cmd2 cmd3 value CS
0x03 0x0C 0xF1
0x03 0x0C 0xFF
Downloaded From projector-manual.com Samsung Manuals 
						

							5-2More Information 
Command Table
CONTROL ITEMCMD1CMD2CMD3VALUE
General Power Power Display OSD 0x00 0x00 0x00 0
OK 1
Cancel 2
Input Source List HDMI HDMI 1 0x0A 0x00 0x01 0
HDMI 2 1
Component Component 0x02 0
S-Video S-Video 0x03 0
Video Video 0x04 0
PC PC 0x05 0
CONTROL ITEMCMD1CMD2CMD3VALUE
Picture Mode Vivid 0x0B 0X00 0x00 0
Dynamic 0X00 0X00 1
Standard 2
Movie13
Movie24
User15
User26
User37
Contrast 0~100 0X01 0x00 (0~100)
Brightness 0~100 0X02 0x00 (0~100)
Sharpness 0~100 0X03 0x00 (0~100)
Color 0~100 0X04 0x00 (0~100)
Tint  (G/R) G50 / R50 0X05 0x00 (0~100)
Color Tem-
perature9300K 0x06 0x00 0
8000K 0x06 0x00 1
6500K2
5500K3
WB R-Offset -50~50 0x07 0x00 (0~100)
G-Offset -50~50 0x01 (0~100)
B-Offset -50~50 0x02 (0~100)
R-Gain 0x03 (0~100)
G-Gain 0x04 (0~100)
B-Gain 0x05 (0~100)
Gamma Film 0x08 0x00 0
Video1
Graphic 2
Downloaded From projector-manual.com Samsung Manuals 
						

							More Information5-2
Picture Save User1 Display OSD 0x0B 0x09 0x00 0
OK 1
Cancel 2
User2 Display OSD 0x01 0
OK 1
Cancel 2
User3 Display OSD 0x02 0
OK 1
Cancel 2
Reset 0x0A 0x00 0
Size 16:9 0x0B 0x00 0
Zoom11
Zoom22
Wide Fit 3
Anamorphic 4
4:35
Digital NR Off 0x0C 0x00 0
On1
Black Level 0 IRE/NOR-
MAL0x0D 0x00 0
7.5 IRE/LOW 1
Color Pattern Off 0x0E 0x00 0
Monochrome 1
Red2
Green3
Blue4
Overscan Off 0x0F 0x00 0
On1
1080/24fps 
Mode Off 0x10 0x00 0
On1
Film Mode Off 0x11 0x00 0
On1
Position (Continuous) LEFT 0x12 0x00 0
RIGHT 1
(Continuous) DOWN 0x13 0x00 0
Up 1
CONTROL ITEMCMD1CMD2CMD3VALUE
Downloaded From projector-manual.com Samsung Manuals 
						

							5-2More Information 
CONTROL ITEMCMD1CMD2CMD3VALUE
Setup install Front-Floor 0x0C 0x00 0x00 0
Front-Ceiling 1
Rear-Floor 2
Rear-Ceiling 3
Lamp Mode Theater 0x01 0x00 0
Bright1
V-Keystone -50~50 0x02 0x00 (0~100)
Background Logo 0x03 0x00 0
Blue1
Black2
Test Pattern  Crosshatch 0x04 0x00 0
Screen size 1
Red2
Green3
Blue4
White5
6500K_Whit
e6
Off7
PC Auto Adjust-
ment0x05 0x00 0
Coarse UP 0x06 0x00 0
DOWN 1
Fine UP 0x07 0x00 0
DOWN 1
Reset Display OSD 0x08 0x00 0
OK 1
Cancel 2
Zoom X1 0x09 0x00 0
X21
X32
X43
LEFT 0x0A 0x00 0
RIGHT1
UP2
DOWN3
Downloaded From projector-manual.com Samsung Manuals 
						

							More Information5-2
Setup Color Stan-
dardHD 0x0C 0x0B 0x00 0
SMPTE-C 1
EBU2
Factory 
Default Display OSD 0x0C 0x00 0
OK1
Cancel2
Option Language English 0x0D 0x00 0x00 0
Deutsch 1
Nederlands 2
Español 3
Français 4
Italiano5
Svenska 6
Português 7
Русский8
中国语9
中國語 （繁
體）A
한국어B
Menu Posi-
tion LEFT 0x01 0x00 0
RIGHT1
UP2
DOWN3
Menu Trans-
parency High 0x02 0x00 0
Medium 1
Low2
Opaque 3
Menu Dis-
play Time 5 sec 0x03 0x00 0
10 sec1
30 sec2
60 sec3
90 sec4
120 sec 5
Stay On 6
CONTROL ITEMCMD1CMD2CMD3VALUE
Downloaded From projector-manual.com Samsung Manuals 
						

							5-3More Information 
5-3 Contact SAMSUNG WORLDWIDE
 •If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care 
center.
 
Option Auto Power 
On OFF 0x0D 0x04 0x00 0
ON1
Sleep Timer OFF 0x05 0x00 0
10 min1
20 min2
30 min3
LED Indica-
torOFF 0x06 0x00 0
ON1
Buzz OFF 0x07 0x00 0
ON1
Information 0x08 0x00 0
NORTH AMERICA
U.S.A 1-800-SAMSUNG(726-7864) http://www.samsung.com/us
CANADA 1-800-SAMSUNG(726-7864) http://www.samsung.com/ca
MEXICO 01-800-SAMSUNG(726-7864)http://www.samsung.com/mx
LATIN AMERICA
 ARGENTINA 0800-333-3733 http://www.samsung.com/ar
BRAZIL 0800-124-421
4004-0000http://www.samsung.com/br
CHILE 800-SAMSUNG(726-7864) http://www.samsung.com/cl
COLOMBIA 01-8000112112 
http://www.samsung.com/co
COSTA RICA 0-800-507-7267 http://www.samsung.com/latin
ECUADOR 1-800-10-7267 http://www.samsung.com/latin
EL SALVADOR 800-6225 http://www.samsung.com/latin
GUATEMALA 1-800-299-0013 http://www.samsung.com/latin
HONDURAS 800-7919267 http://www.samsung.com/latin
JAMAICA 1-800-234-7267 http://www.samsung.com/latin
NICARAGUA 00-1800-5077267 http://www.samsung.com/latin
PANAMA 800-7267 http://www.samsung.com/latin
PUERTO RICO 1-800-682-3180 http://www.samsung.com/latin
REP. DOMINICA 1-800-751-2676 http://www.samsung.com/latin
CONTROL ITEMCMD1CMD2CMD3VALUE
Downloaded From projector-manual.com Samsung Manuals