Samsung S24a300bz User Manual

							3-13Using the product
 SETUP&RESET
MenuDescription
ResetUse this function to restore t
he visual quality and color settings to the factory defaults.
LanguageSelect a language for the OSD.
 The selected language is only applied to the produ
ct OSD. This setting does not affect the other 
functions of the PC.
 
Eco Saving This function provides user a low 
power mode which is realized by lo wering the current of the display 
panel.
• 
When  is selected, the power consumption is about 75% of default setting.
•  When  is selected, the power consumption is about 50% of default setting.
•  When  is selected, the  function is turned Off .
 This menu is unavailable when < Bright> is set to  mode. 
Off Timer On/OffYou can turn the Off Timer on or off.
•  - 
Off Timer Setting Turns the power off automatically when the configured time is reached. When  of  is sele
cted,This function is available only.  
PC/AV ModeSet to PC when connected to a PC.
Set to AV when connected to an AV device.
 • This function does not support Analog mode.
• Supplied for the wide models only such as 16:9 or 16:10.
• If the monitor (when set to Digital) is in power saving mode or is displaying the message 
, press the MENU button to display the On Screen Display (OSD). 
You can select   or .
 
Key Repeat Time Controls the repeat delay of a button.
You can set to ,  or . If  is selected, the button only 
responds once.
• - 
 
						

							Using the product3-13
 INFORMATION
Customized KeyYou can set the function of the Cust
omized Key to one of the following.
• < Angle> - < Bright> -  - 
Auto Source •  - The monitor automatically selects an input signal.
•  - Users have to manually select an input signal. Not applicable to analog (D-SUB)-o
r-digital (DVI)-dedicated models. 
Display TimeThe OSD automatically disappears if 
no action is taken by the user.
You can determine the time to  wait before the OSD is hidden.
•  -  -  - 
Menu Transparency You can select the transparency of the OSD.
•  - 
MenuDescription
INFORMATIONShows the frequency and resolution set on the PC.  For models with an Analog interface only,  is not shown in the . 
MenuDescription
 
						

							4-1Installing the Software
4 Installing the Software
4-1 Natural Color
What is Natural Color ?
 
This software works only for Samsung products and enables adjusting the displayed colors on the product and matches the 
colors on the product with the colors of the printed pictures. For more information, refer to the online help of the software (F1).
 
The Natural Color is provided online. You can do wnload it from the website below and install;
http://www.samsung.com/us/consumer/learningresourc es/monitor/naturalcolorexpert/pop_download.html 
 
						

							Installing the Software4-2
4-2 MagicTune
What is MagicTune?
 MagicTune is a software program that helps with monitor adjustments by providing comprehensive descriptions of monitor 
functions and easy-to-understand guidelines. 
Users can adjust the product with the mouse and the keyb oard without using the operating buttons of the product.
Installing the Software
1.Insert the installation CD  into the CD-ROM drive. 
2. Select the MagicTune setup program. 
 If the pop-up screen for the software installation does no t appear on the main screen, find and double-click the 
MagicTune setup file on the CD-ROM.
 
3. Select the installation language and click [Next].
4. Complete the remaining software installation steps a ccording to the instructions displayed on the screen.
 • The software may not work properly if you do not restart the computer after the installation.
• The  MagicTune icon may not appear depending on th e computer system and the product specifications.
• If the shortcut icon does not appear, press the F5 key.
 
Restrictions and Problems with the Installation (MagicTune™)
The installation of MagicTune™may be affected by the  graphics card, motherboard and the networking environment. 
System Requirements
OS
•Windows 2000
•Windows XP Home Edition
•Windows XP Professional
•Windows Vista 32Bit
•Windows 7 32Bit
 For MagicTune™, Windows 2000 or later is recommended.  
Hardware
•At least 32MB of memory 
•At least 60MB of free space on the hard disk drive 
 For more information, refer to the website. 
Removing the Software
You can only remove MagicTune™through [Add or Remove Programs ] in Windows.
To remove MagicTune™, complete the following steps.
1.Click [Start] select [Settings], and select [Control Panel] from the menu.
For Windows XP, click [Start], and select [Control Panel] from the menu. 
2. Double-click the [Add or Remove Pr ograms] icon in the Control Panel. 
 
						

							4-2Installing the Software
3.In the [Add/Remove] window, find and select MagicTune™so that it is highlighted. 
4. Click [Change or Remove Programs] to remove the software. 
5. Select [Yes] to start removing MagicTune™. 
6. Wait until a message box appears informing you that the software has been removed completely. 
 For technical support, the FAQ (frequently asked questions) or information about the software upgrade for MagicTune™, 
please visit our website. 
 
 
						

							Installing the Software4-3
4-3 MultiScreen
What is MultiScreen ?
MultiScreen enables users to use the monitor by partitioning multiple sections.
Installing the Software
1.Insert the installation CD  into the CD-ROM drive. 
2. Select the MultiScreen setup program.
 If the pop-up screen for the software installation does no t appear on the main screen, find and double-click the 
MultiScreen setup file  on the CD-ROM.
 
3.When the Installation Wizard appears, click [Next].
4. Complete the remaining software installation steps a ccording to the instructions displayed on the screen.
 • The software may not work properly if you do not restart the computer after the installation.
• The MultiScreen icon may not appear depending on t he computer system and the product specifications.
• If the shortcut icon does not appear, press the F5 key.
 
Restrictions and Problems with the Installation (MultiScreen)
The MultiScreen installation may be affected by the gra phics card, motherboard and the networking environment. 
Operating System
OS
•Windows 2000
•Windows XP Home Edition
•Windows XP Professional
•Windows Vista 32Bit
•Windows 7 32Bit
 For MultiScreen, the operating systems Windows 2000 or later is recommended.  
Hardware
•At least 32MB of memory 
•At least 60MB of free space on the hard disk drive 
Removing the Software 
Click [Start], select [Settings]/[Control Panel], and then double-cli ck [Add or Remove Programs]. 
Select MultiScreen from the program li st and click the [Add/Delete] button. 
 
						

							5-1Troubleshooting
5 Troubleshooting
5-1 Monitor Self-Diagnosis
 • You can check if the product is working properly using the Self-Diagnosis function.
• If a blank screen is displayed and the Power LED blinks even if the product and the PC are properly connected, perform  the self-diagnosis function according to the procedures below.
 
1.Turn the product and the PC off.
2. Separate the signal cable from the product .
3. Turn the product on. 
4. If the product is working properly, the  message appears.
In this case, if a blank screen is displayed again, make sure  that there is no problem with the PC and the connection. The 
product is working properly.
 
						

							Troubleshooting5-2
5-2 Before Requesting Service
 Please check the following before requesting After-Sales service. If the problem continues, please contact your nearest 
Samsung Electronics Service Center.
 
A blank screen appears / I cannot turn the product on
Is the power cord connected properly? Check the connection status of the power cord.
Is the  message displayed on the 
screen? (Connected using the D-sub cable)
Check the cable connecting the PC and the product.
(Connected using the DVI cable)
If the message appears on the 
screen even if the cable is 
properly connected, recheck the input signal by pressing the [ 
 ] button of the product.
Is the  message displayed on the 
screen?  This occurs when the signal from the graphics card exceeds 
the maximum resolution or th
e maximum frequency of the 
product.
In this case, set up the appropriate resolution and the fre-
quency for the product.
Is a blank screen displayed and does the power LED blink at 
a 1 second interval? 1.
This occurs when the power saving function is running.
If you click the mouse or press any key, the screen will be 
turned on.
2. If the “Check Signal Cable” cond ition persists for more than 
five minutes, Lossless mode wil l be activated.In Lossless 
mode, the backlight of the monitor will turn off.
Did you connect wi th a DVI cable? If you connect the DVI cable when the PC has booted up or if 
you reconnect the DVI cable after disconnecting the cable 
while using a PC, the screen may not be displayed because 
some graphics cards do not output the video signal.
In this case, reboot the PC wh
ile the DVI cable is connected.
THE IMAGE IS TOO LIGHT OR TOO DARK.
Adjust the  and .
(Refer to the , )
The display brightness can differ according to the mode set for < Angle>.
If < Bright> is set to , the display brightness can differ according to the input signal.
The on screen adjustment menu (OSD) does not appear.
Did you cancel the screen adjustment? Check if the OSD Adjustment Lock function is set to Off.
The color is weird / The picture is displayed in black and white
Is the entire screen displayed in  the same color as if viewing 
the screen through a cellophane paper?  Check the cable connection to the computer.
Reinsert the graphics card in
to the computer completely.
Is the graphics card configured correctly? Set up the graphics card referring to the user manual. 
The display area suddenly moves to an edge or to the center.
Did you change the graphics card or the driver? Please press the [AUTO] button to run the auto adjustment 
function.
 
						

							5-2Troubleshooting
Did you change the resolution and frequency appropriate to 
the product?Set the resolution and the frequency to the appropriate values 
in the graphics card 
refer to the (Standard Signal Mode Table) 
Is the graphics card configured correctly?
Set up the graphics card referring to the user manual. 
The pictures are out-of-focus.
Did you change the resolution and the frequency appropriate 
to the product? Set the resolution and the frequency to the appropriate values 
in the graphics card
refer to the (Standard Signal Mode Table) 
The color is displayed in 16 bit (16 colors). The color has been changed after changing the graphics card.
Did you install the device driver for the product?Windows XP : Set the color again by selecting Control Panel 
→ Appearance and Themes 
→ Display → Settings. 
Windows ME/2000 : Set the color again by selecting Control 
Panel  → Display  → Settings. 
Windows Vista : Change the color settings by selecting Con-
trol Panel → Appearance and Personalization  → Personaliza-
tion  → Display settings.
Windows 7 : Change the color settings by selecting Control 
Panel  → Appearance and Personalization  → Display  → 
Adjust resolution → Advanced settings  → Monitor.
( For more information,  refer to the Windows user manual for 
the computer. )
Is the graphics card configured correctly? Configure the color again in accordance with the new graph-
ics card driver. 
When I connect the monitor, the Unk
nown monitor, Plug&Play (VESA DDC) mo nitor found message is displayed.
Did you install the device driver for the product? Install the device driver referring to the descriptions about the 
driver installation.
Check if all the Plug&Play (VESA DDC) functions are sup-
ported referring to the User Manual of the graphics card.Install the device driver referring to the descriptions about the 
driver installation.
When I look at the exterior edges of the product, small alien substances appear on it. 
Since this product is designed so that the 
color has a soft appearance by coating it with a transparent material over the black  
edges, such things may be seen. This is not a defect of the product.
A “beep, beep” sound is heard when booting the computer.
If the beep sound is generated 3 or more times when booting up the computer, please request service for the computer.
The display area suddenly moves to an edge or to the center.
 
						

							Troubleshooting5-3
5-3 FAQ
FAQ!PLEASE TRY THE FOLLOWING!
How can I change the frequency (refresh rate) of the video 
signal? You have to change the frequency of the graphics card.
Windows XP : Change the frequency by selecting Control 
Panel 
→ Appearance and Themes → Display → Settings 
→ Advanced → Monitor, and then change the refresh rate 
under Monitor Settings. 
Windows ME/2000 : Change the frequency by selecting Con-
trol Panel  
→ Display  → Settings → Advanced →  Monitor, 
and then change the refresh rate under Monitor Settings.
Windows Vista : Change the frequency by selecting Control 
Panel  → Appearance and Personalization  → Personalization 
→ Display settings
  →  Advanced settings → Monitor, and 
then change the refresh rate under Monitor Settings. 
Windows 7 : Change the frequency by selecting Control Panel 
→ Appearance and Personalization  → Display → Adjust reso-
lution 
→ Advanced settings → Monitor, and then change the 
refresh rate under Monitor Settings. 
(For more information , refer to the User Manual of the com-
puter or the graphics card.)
How can I change the resolution? Windows XP : Change the resolution by selecting Control 
Panel 
→ Appearance and Themes  → Display  → Settings. 
Windows ME/2000 : Change the resolution by selecting Con-
trol Panel  → Display  → Settings. 
Windows Vista : Change the resolution by selecting Control 
Panel  → Appearance and Personalization  → Personalization 
→ Display settings.
Windows 7 : Change the resolution by selecting Control Panel 
→ Appearance and Personalization  → Display → Adjust reso-
lution.
(For more information , refer to the User Manual of the com-
puter or the graphics card.)
How can I use the power saving function? Windows XP : Configure it by selecting Control Panel 
→ 
Appearance and Themes  → Display → Screen Saver Setting 
or configure it in the BIOS Setup of the computer.
Windows ME/2000 : Configure it  by selecting Control Panel → 
Display  → Screen Saver Setting or Configure it in the BIOS 
Setup of the computer. 
Windows Vista : Change settings by selecting Control Panel 
→ Appearance and Personalization  → Personalization → 
Screen Saver. You can also use the BIOS SETUP menu on 
the PC.
Windows 7 : Change settings by selecting Control Panel  → 
Appearance and Personalization  → Personalization  → 
Screen Saver. You can also use the BIOS SETUP menu on 
the PC.
( For more information,  refer to the Windows user manual for 
the computer. )