Samsung Rsj1fers User Manual

setting up _11

setting up your side-by-side 
refrigerator
Removing the freezer door
A few things to mention first.
•	Make sure that you lift the door straight up so the hinges are not bent \
or broken.
•	Be careful not to pinch the water tubing and wire harness on the door.
•	Place doors on a protected surface to prevent scratching or damage.
1.	With the Freezer door closed, remove the upper hinge cover 1 using a screwdriver, and 
then disconnect the wires by gently pulling them apart .
....

1_ setting up

Removing the Fridge Door
1.	With the door closed, remove the upper hinge cover 1 using a screwdriver.
.	Remove hinge screws  and the ground screw  by turning counter-clockwise, and take 
off the upper hinge . Be careful that the door does not fall on you as you are removing it.
.	Remove the door from the lower hinge  by lifting the door straight up .
.	Remove the lower hinge  from the bracket in  by gently lifting the lower hinge...

setting up _1

setting up your side-by-side 
refrigerator
rEattaChing thE rEfrigErator Doors
Once you have safely placed your refrigerator where you plan for it to s\
tay, it is time to put the doors back on.
Reattaching the Freezer Door
1.	Insert the lower hinge 1 back into 
						the lower hinge bracket .
.	Replace the freezer door by inserting the hose  back into the lower corner of the door 
and then into the hole on the lower hinge . Gently pull the hose back down so that...

1_ setting up

Reattaching the Fridge Door
1.	Insert the lower hinge 1 back 
into the lower hinge bracket .
.	Fit the hole in the corner of the fridge door  over         the 
lower hinge .
.	Insert the upper hinge shaft  into the hole on the hinge 
. Make sure the hinge is level between the upper hinge 
hole  and the hole on the top of the cabinet . Then, 
reattach hinge screws  and the ground screw 10 by 
turning it in a clock wise direction....

setting up _1

setting up your side-by-side 
refrigerator
Reattaching the Water Supply Line
1.	Insert the water line 1 into the coupler .
.	Then, tighten the screw on the hose clamp .
Reattaching the Front Leg Cover
Before attaching the cover, check water connector for leakage. 
Replace the front leg cover by turning the three screws clockwise, as sh\
own in the figure.
front Leg Cover
screw

1
01 sEtting uP

DA68-01651A(JM)-EN(0.4).indd   152007.5.25   3:18:17 PM
        

1_ setting up

LEVELing thE rEfrigErator
Now that the doors are back on the refrigerator, you will want to make s\
ure the refrigerator is level so 
you can then make final adjustments. If the refrigerator is not level,\
 it will not be possible to get the doors 
perfectly even.
The front of the refrigerator is also adjustable.
When the Freezer door is lower than the fridge
Insert a flat-blade screwdriver into a notch on the Leg, turn it clock\
wise or counter clockwise to 
level the freezer.
When...

setting up _1

setting up your side-by-side 
refrigerator
MaKing Minor aDJustMEnts to thE Doors
Remember, a leveling refrigerator is necessary for getting the doors per\
fectly even. If you need help, 
review the previous section on leveling the refrigerator.
When	the	door	of	the	freezer	is	lower	
than	the	fridge
When	the	door	of	the	freezer	is	higher	
than	the	fridge
In both cases the process to correct the imbalance is the same. Open the\
 doors and adjust 
them, one at a time, as follows:
1....

1_ setting up

.	After adjusting the doors, turn the nut 1 clockwise  until it reaches the lower end of 
the bolt, then tighten the bolt again with the wrench  to fix the nut in place 1.
If you do not secure the nut firmly, the bolt may release.
ChECKing thE watEr DisPEnsEr LinE (oPtionaL)
A water dispenser is just one of the helpful features on your new Samsun\
g refrigerator. To help promote 
better health, the Samsung water filter removes unwanted particles fro\
m your water. However,...

setting up _1

setting up your side-by-side 
refrigerator
instaLLing thE watEr DisPEnsEr LinE
Connecting the water line to the refrigerator
1.    Remove the cap from water line on the unit and insert compression nut to\
 the water line on 
the unit after disassembling from provided water line.
2. Connect both water line from the unit and water line provided kit.
3.  Tighten the compression nut onto the compression fitting. Be careful n\
o gap between two 
items.
4. Turn water on and check for any...

0_ setting up

.	Remove the filter’s protective cap 
and then position and insert the 
filter into the filter housing.
.	Slowly turn the water filter 
clockwise 90º to align with the 
indication mark on the cover, 
locking the filter in position. Make 
sure that the indicator is lined up 
with the “lock” position. Remember, 
do not over-tighten.
If your model contains wine shelf, you should remove the wine shelf befo\
re installing water 
filters.
Removing any residual matter inside the...