Samsung Rsh7pnsw User Manual

							setting up _11
01 SETTING UP
LEVELLING THE REFRIGERATOR
Now that the doors are back on the refrigerator, you 
will want to make sure the refrigerator is level so you 
can then make fi nal adjustments. If the refrigerator 
is not level, it will not be possible to get the doors 
perfectly even.
The front of the refrigerator is also adjustable.
When the Freezer door is lower than 
the fridge
Insert a fl at-blade screwdriver into a notch on the 
Leg, turn it clockwise or counter clockwise to level 
the freezer.
When the Freezer door is higher than 
the fridge
Insert a fl at-blade screwdriver into a notch on the 
Leg, turn it clockwise or counter clockwise to level 
the fridge.
Refer to the next section for the best way to 
make very minor adjustments to the doors.
MAKING MINOR ADJUSTMENTS 
TO THE DOORS
Remember, a level refrigerator is necessary for getting 
the doors perfectly even. If you need help, review the 
previous section on levelling the refrigerator.
In the process for adjusting both the doors is the 
same. Open the doors and adjust them, one at a 
time, as follows:
1.  Unscrew the 
nut 
1 from the 
lower hinge until 
it reaches the 
upper end of the 
bolt 
2.
When you release the nut 
1, make sure that 
you use the Allen wrench provided 3 to loosen 
the bolt 2 in a counter-clockwise direction. 
You should then be able to unscrew the nut 1 
with your fi ngers.
2.   Adjust the 
height difference 
between the 
doors by turning 
the bolt 
2 
clockwise  
or counter clockwise .
When you turn clockwise 
, the door will 
move up.
3.   After adjusting 
the doors, turn 
the nut 
1 
clockwise  
until it reaches 
the lower end 
of the bolt, then 
tighten the bolt again with the wrench 
3 to fi x 
the nut in place 1.
If you do not secure the nut fi rmly, the bolt may 
release.
Leg
Screw Driver
Screw Driver
Leg
Adjustment 
part
When the door of the freezer 
is higher than the fridge
3
2
1
Wrench
Bolt
Nut
3
2
Wrench
Bolt
3
2
1
Wrench
Bolt
Nut
 
						

							12_ setting up
CHECKING THE WATER 
DISPENSER LINE (OPTIONAL)
A water dispenser is just one of the helpful features 
on your new Samsung refrigerator. To help promote 
better health, the Samsung water fi lter removes 
unwanted particles from your water. However, it 
does not sterilize or destroy microorganisms. You 
will need to purchase a water purifying system to do 
that. In order for the icemaker to operate properly, 
water pressure of 138 ~862 Kpa is required. Under 
normal conditions, a 170 cc paper cup can be fi lled 
in 10 seconds. If the refrigerator is installed in an area 
with low water pressure (below 138 Kpa), you can 
install a booster pump to compensate for the low 
pressure. Make sure the water storage tank inside 
the refrigerator is properly fi lled. To do this, press the 
water dispenser lever until the water runs from the 
water outlet.  
Water Line installation Kits are included. You can 
fi nd it in one of the freezer drawers.
USING THE ICE MAKER (OPTIONAL)
To Remove the Ice Bucket
-  Hold the handle as shown in fi gure1.-   Slightly pull up the bottom part.-  Take out the ice bucket slowly.
To Refi t The Ice Bucket
-  Assemble it in the reverse 
order of disassembly.
-  Push the bucket in fi rmly until 
you hear a clicking sound.
-   
When the bucket does not fi t 
into its place, turn the gear 
handle on its back by 90 
degrees and reinstall it again 
as shown in fi gure 2.
Normal Operation
-  Any sounds you hear when 
the ice maker dumps ice into 
the bucket are part of normal 
operation.
-  Not dispensing ice for long 
periods may cause ice 
clumps in the ice bucket. 
Remove the remaining ice 
and empty the bucket.
-  When ice does not come 
out, Check for any ice stuck 
in the chute and remove it.
-  
The fi rst batch of ice cubes may 
be small due to air in the pipe 
after connection, any air will be 
purged during normal use.
-  When ICE OFF blinks on the display panel, 
reinsert the bucket and/or make sure it’s 
installed properly.
-  When the door is open, the Ice and water 
dispenser do not work.
-  If you close the door hard, it may cause 
water spilling over the ice maker.
-  To prevent dropping the ice bucket, use 
both hands when removing it.
-  To prevent injury, be sure to clean up any 
ice or water that may have   dropped on 
the fl oor.
-  
Do not let children hang on the ice dispenser 
or on the bucket.
They may get hurt.
-  Be sure not to put your hand or any object 
into the ice chute.
   It may cause personal injury or damage 
mechanical parts.
INSTALLING THE WATER 
DISPENSER LINE
For Interior model
Parts for water line Installation
Connecting to the water supply line1. fi rst, shut off the main water supply line.
2. locate the nearest cold, drinking water line.
3. follow the Water line Installation Instructions in the 
    installation kit.
 
Figure2
Ice ChuteIce Chute
Figure1
CAUTION
CAUTION
The water line must be connected
to the cold water pipe. If it is connected 
to the hot water pipe, it may cause the
purifi er to malfunction.
 1  Water line fi xer and screws 2 Pipe connector
 3  Water line 4  Clip 5  Water Filter
 
						

							setting up _13
01 SETTING UP
4.  After connecting the water supply to the water 
fi lter, turn your main water supply back on and 
dispense about 1l to clear and prime the water 
fi lter.
Connecting the water line to the 
refrigerator
1.  Remove the dust cap from the water line on the 
rear of the unit and fi t a compression nut from the 
install kit.
2.  Remove the water pipe from the install kit and fi t a 
compression nut to one end.
3.  Join the two pipes together using the compression 
joint from the install kit ensuring that the joint is 
water tight.
4.  Join the other end of the install pipe to the main 
water supply and turn on the water to check for 
leaks.
Only connect the water line to a drinkable water 
source.
If you have to repair or disassemble the water 
line, cut off 6.5mm of the plastic tubing to
make sure you get a snug, leak-free connection.  
Before being used, the leakage in 
these places should be examined
•    Samsung Warranty does not cover WATER LINE 
INSTALLATION.
•   The cost of connection to a water supply is at the 
customer expense, unless included in the delivery 
charge (refer to the delivery agreement with the 
seller) 
•   Please contact Plumber or Authorised Installer for 
the installation if needed.
•   If Water leakage occurs due to improper 
installation, Please contact installer.
INSTALLING THE WATER 
DISPENSER LINE
For Exterior model
Parts for water line Installation 
Connecting to the water supply line
Connect the water pipe with coupler and tap.
1. Close the main water tap.
2. Connect coupler “A” to the tap.
Close MainClose MainWater pipeWater pipe
Close MainClose MainWater pipeWater pipeNO GAPNO GAP
Water line fi xer and screwsPipe connector
Water line
Purifi er  lock-clip
Purifi er
Remove Remove capcap
Water LineWater Linefrom unitfrom unit
Water LineWater Linefrom Kitfrom Kit
No gapNo gap
Loosen aLoosen a
CAUTIONCAUTION
The water line must be connected to the cold 
water pipe. If it is connected to the hot water 
pipe, it may cause the purifi er to malfunction.
 
						

							14_ setting up
select the location where the purifi er is to 
install. (Model with the purifi er)
-    If you wish to reassemble the water inlet and outlet 
sides of the purifi er during purifi er installation, see 
the reference illustration.
-    Cut the water line attached to the purifi er to the 
appropriate place after measuring the distance 
between the purifi er and the cold water tap.
Replacement Instructions
1. Shut off water supply.
2. Note the Flow direction on the fi lter.
3.  Insert water supply tube into the inlet side of the 
fi lter until the tube stop.
4.  After inserting tube, put together the clip strongly.   
The Clip fi x the tube.
5.  Turn on the water and check for leaks. If leaks 
occur, repeat step 1,2,3,4. If leaks persist, 
discontinue use and call your supporting dealer.
6. Flush fi lter for 5 minutes before use.
Remove any residual matter inside the 
purifi er. (Model with the purifi er)
-   Open the main water tap to check whether water 
is running through the water tube on the water inlet 
side of the purifi er.
-   If water does not come out through the line, check 
whether the tap is open.
-   Leave the tap open until clean water is running 
out and any residual matter that built up during 
manufacturing has been removed.
Attach the purifi er lock-clip.-   Hold the purifi er lock-clip in the appropriate position 
(under the sink for example) and fi x it tightly into 
place where to screw.
Secure the purifi er in position.-   Fix the purifi er in position, as shown in the fi gure on 
the right.
WARRANTY INFORMATIONThis water line installation is not covered by the 
refrigerator or ice maker manufacturer’s warranty.
Follow these instructions carefully to minimise the risk of 
expensive water damage.
Note:If the coupler does not fi t on the current tap, go
the nearest authorised service dealer and purchase the 
right couplers fi ttings.
COUPLER “A”
TA P
COUPLER SIDE OF
PURIFIER
WATER INLET
SIDE OF PURIFIERLINE OUTLET
90 degree
PURIFIER WATERCAUTION
Locking ClipLocking Clip
Insert Locking Clip After Insert Locking Clip After tube seatedtube seated
WATER SUPPLY
INLET SIDEPERMEAT FLOW DIRECTION
Note :  You must also ensure 
that the cut is square 
and not at any sort 
of angle as this could 
cause a leak
WATER LINEPURIFIER
WATEROUTLET SIDE
OF PURIFIER
PURIFIER LOCK-CLIP
WATER TUBE
PURIFIER LOCK-CLIP
PURIFIER
 
						

							setting up _15
01 SETTING UP
Connect the water line to the 
refrigerator.
-  Remove the compressor cover of the refrigerator.
-   Connect the water line to the valve, as shown in 
the fi gure.
-  When connected, check if there is any leakage.
    If any, repeat the connection.
-  Reattach the compressor cover of the refrigerator.
Secure the water line.
-   Using clip ”A”, fi x the water 
line to the wall (the back of 
refrigerator).
-    When the water line is 
secure, make sure whether 
the water line is not 
excessively bent, pinched or 
squashed.
Removing any residual matter inside 
the water supply line after installing 
fi lter.
1.   
  Turn ON the main water supply & turn OFF the 
valve to the  water supply line.
2.    Run water through the dispenser until the water 
runs clear (approx. 1L). This will clean the water 
supply system and remove air from the lines.
3.   
  Additional fl ushing may be required in some 
households.
4.    Open the refrigerator door and make sure there 
are no water leaks coming from the water fi lter.
A newly installed water fi lter cartridge may cause 
water to briefl y spurt from the water dispenser. 
This is due to air getting into the line. It should 
pose no problem to operation.
WATER LINE
INSTRUCTIONS
COMPRESSOR COVER OF
REFRIGERATORCONNECTION NUT
CLIP A
WATER LINE
 
						

							16_ operating
operating the SAMSUNG  
side-by-side refrigerator
OPERATING THE REFRIGERATOR
USING THE CONTROL PANEL / 
DIGITAL DISPLAY
 
POWER 
FREEZE 
BUTTON
Speeds up the time needed 
to freeze products in the 
freezer. This can be helpful 
if you need to quickly freeze 
items that spoil easily or if the 
temperature in the freezer 
has warmed dramatically (For 
example, if the door was left 
open).
FREEZER 
BUTTON
Press the Freezer button to 
set the freezer to your desired 
temperature, You can set the 
temperature between -14°C 
(8°F) and -25ºC (-14°F).
ICE TYPE 
BUTTONUse this button to choose 
Cubed, Crushed or to turn the 
Ice feature off.
FILTER 
CHANGE 
BUTTONWhen you change the fi lter, 
press this button for 3 
seconds to reset the fi lter 
schedule.
VACATION 
BUTTON
If you are going on vacation 
or business trip or you do not 
need to use the refrigerator, 
press the Vacation button. 
When you select vacation 
button for fridge compartment 
off, display LED of Vacation will 
be on. 
It is strongly requested to 
remove foods in the fresh-
food compartment and do 
not leave the door open 
when you select Vacation 
function.
CHILD 
LOCK 
FUNCTION
By pressing the Vacation 
button and the Fridge button 
simultaneously for 3 seconds, 
all buttons will be locked. The 
Water dispenser lever and 
the Ice lever will not work 
either. To cancel this function, 
Press these two buttons for 3 
seconds again.
FRIDGE 
BUTTON
Press the Fridge button to 
set the fridge to your desired 
temperature.
You can set temperature 
between 1°C and 7°C (34°F 
and 45°F).
When you use Power Freeze the energy 
consumption of the refrigerator will increase.
Remember to turn it off when you don’t 
need it and return the freezer to your original 
temperature setting.
If you need to freeze large amount of food stuff, 
activate Power Freeze function at least 24 hours 
before.
5
6
7
1
3
4
2
COOLSELECT MODEL
DISPENSER MODEL
NORMAL MODEL
1
2
3
4
5
6
7
 
						

							operating _17
02 OPERATING
CONTROLLING THE 
TEMPERATURE
CONTROLLING THE FREEZER 
TEMPERATURE
The freezer temperature can be set between -14°C 
(8°F) and -25ºC (-14°F) to suit your particular needs. 
Press the Freezer button repeatedly until the desired 
temperature is shown in the temperature display. 
Keep in mind that foods like ice cream may melt at 
-16ºC (4°F).
The temperature display will move sequentially from 
-14°C (8°F) and -25ºC (-14°F). When the display 
reaches -14ºC (8°F), it will begin again at -25ºC 
(-14°F).
Five seconds after the new temperature is set the 
display will again show the actual current freezer 
temperature. However, this number will change as 
the Freezer adjusts to the new temperature.
The door guards in the freezer of this model  are 
the two star sections, so the temperature in 
two star sections are slightly higher than other 
freezer compartment.
CONTROLLING THE FRIDGE 
TEMPERATURE
The refrigerator temperature can be set between 7ºC 
(46°F) and 1ºC (34°F) to suit your particular
needs. Press the Fridge button repeatedly until the 
desired temperature is shown in the temperature 
display. The temperature control process for the 
Fridge works just like the Freezer process. Press the 
Fridge button to set your desired temperature. After 
a few seconds, the Fridge will begin tracking towards 
the newly set temperature. This will be refl ected in the 
digital display. 
The temperature of the freezer or the refrigerator 
may rise from opening the doors too frequently, 
or if a large amount of warm or hot food is 
placed in either side. This may cause the digital 
display to blink. Once the freezer and refrigerator 
return to their normal set temperatures the 
blinking will stop. If the blinking continues, 
you may need to “reset” the refrigerator. Try 
unplugging the appliance, wait about 10 minutes 
and then plug back in.
USING THE ICE AND COLD 
WATER DISPENSER
Press the Ice Type button to select the type of ice 
you want
Ice is made in cubes. When you select 
“Crushed”, the icemaker grinds the ice cubes 
into crushed ice.
Dispensing ice 
Place your glass underneath the ice outlet and push 
gently against the ice dispenser lever with your glass. 
Make sure the glass is in line with the dispenser to 
prevent the ice from bouncing out.
Using the Water Dispenser
Place a glass underneath the water outlet and 
push gently against the water dispenser lever with 
your glass. Make sure the glass is in line with the 
dispenser to prevent the water from splashing out.
No IceSelect this if you want to 
turn off the icemaker
 
						

							18_ operating
GUARD FRE-UPP
(Optional)
•    Do not put your fi ngers, hands or any 
other unsuitable objects in the chute or 
ice-maker bucket.
    -  It may result in personal injury or material 
damage.
•    Never put fi nger or any other objects in 
the dispenser opening.
    - It may cause injury.
•    Use only the ice maker provided with the 
refrigerator.
•     
 
The water supply to this refrigerator must 
only be installed/connected by a suitably 
qualifi ed person and connect to a potable 
water supply only.
•    In order to operate the ice maker properly, 
water pressure of 138 ~ 862 Kpa is 
required.
•    If you have a long vacation or business 
trip and won’t use water or ice 
dispensers, close the water valve.
    - Otherwise, water leakage may occur.
•     
Wipe excess moisture from the inside and 
leave the doors open.
    - Otherwise, odor and mold may develop.       
To get more space,you can remove top freezer 
drawer since it does not affect thermal and 
mechanical characteristics. A declared storage 
volume of frozen food storage compartment is 
calculated with these drawers removed.
For more space, you can 
store food with Guard 
FRE-UPP instead of the ice 
bucket.
If you remove the ice bucket, 
ICE OFF will blink on the 
display panel. USING THE COOLSELECT 
ZONE™ DRAWER (OPTIONAL)
Quick Cool
•  You can use the Quick Cool feature with the 
CoolSelect ZoneTM.
•  “Quick Cool” allows 1~3 canned beverages to cool 
within 60 min.
•  To cancel this function, press the “Quick Cool” 
button again. CoolSelect Zone
TM returns to the 
previous temperature.
•  When “Quick Cool” ends, it returns to the “Cool” 
temperature setting.
Thaw
•  Drips loss and quality deterioration of meats 
reduces the freshness of foods.
•  
After “Thaw” is selected, warm and cold air is 
alternately supplied into the CoolSelect ZoneTM 
Drawer.
•  Depending on the weight of meat, thawing time 
can be selected for 4 hrs, 6 hrs, 10 hrs, and 12 hrs 
sequentially.
•  When “Thaw” ends, CoolSelect Zone
TM display 
returns to “Zero Zone” condition.
•  When “Thaw “ ends, there are no juice in the meats 
and they are half-freezed condition so it is easy to 
cut them for cooking.
•  To cancel this option, press any button except 
“Thaw”.
•  The approximate thawing time of meat and fi sh are 
shown below. (Based on 1inch thickness)
THAW TIME WEIGHT
4hours 363g (0.8Ib)
6hours 590g (1.3Ib)
10hours 771g (1.7Ib)
12hours 1000g (2.2Ib)
Depending on the size and thickness of meat 
and fi sh, the thawing time may vary.
The above weight represents the total weight of 
food in the CoolSelect Zone
TM Drawer.
Ex) The total thawing time for 400g frozen beef 
and 600g frozen chicken will be 10 hours.
With the “Thaw” option, food which is not 
needed to thaw in the CoolSelect Zone
TM 
Drawer should be removed.
WARNING
CAUTION
WARNING
 
						

							operating _19
02 OPERATING
Zero Zone (0ºC)
•  When “Zero Zone” is chosen, the temperature 
of the CoolSelect ZoneTM Drawer is kept at 0 ºC 
regardless of the set refrigerator temperature.
•  “Zero Zone” temperature helps keep meat or fi sh 
fresh longer.
Cool
•  When “Cool” is chosen, the temperature will be the 
same as the set temperature of the refrigerator. The 
digital panel shows the same temperature as that of 
the display panel.
•  The CoolSelect Zone
TM Drawer allows extra 
refrigerator space.
Depending on the beverages, the cool-down 
time may vary.
For “Quick Cool” option, food stored in 
the CoolSelect Zone
TM Drawer should be 
removed.
REMOVING THE FREEZER 
ACCESSORIES
Cleaning and rearranging the interior of the freezer is 
simple. 
1.  Remove the Glass shelf by pulling the shelf out as 
far as it will go. Then, gently lift it up and remove it.  
2.   Remove the door bin by holding the door bin with 
both hands and then gently lift it up.3.   Remove the Plastic drawer by pulling it out and 
slightly lifting it up.
4. ice bucket (freezer)
     Remove the Icemaker Bucket by lifting up and 
pulling it out slowly.
    •  Grip the handle as 
shown in the fi gure
    • Lift the low part slightly
    •  Take the ice bucket out 
slowly.
Do not use excessive force when removing the 
cover.
Otherwise, the cover may break and cause 
injury.
WARNING
 
						

							20_ operating
CAUTION
REMOVING THE FRIDGE 
ACCESSORIES
1.   Remove the spill Proof Glass Shelf by pulling the 
shelf out as far as it will go. Then, gently lift it up 
and gently remove it.  
2.   Remove the Vegetable & Fruit Drawer by 
pressing on the indentations found on the inside 
left and right sides of the Veggie Box/Dry Box 
cover and remove by 
pulling forward.
      Holding the drawer 
with one hand, lift it up 
a little bit while pulling 
it forward and take it 
out of the refrigerator.
3.   Remove the Gallon Door Bin by holding the bin 
with both hands and gently lifting it up.
4.  The Z Shelf is attached to the cabinet wall.
      Remove the wine shelf by sliding it up and gently 
lifting the shelf out of the tabs.  
Ensure that the Z Shelf is fi tted as shown in 
the diagram and not upside down.
Before removing any accessories, make sure that 
no food is in the way.
When possible, remove the food altogether to 
reduce the risk of accidents.
To get the best energy effi ciency of this product, 
please leave all selves, drawers and baskets on 
their original position like as illustration in page 
(18).
CLEANING THE REFRIGERATOR
Do not use Benzene, Thinner or Clorox™ 
for cleaning. 
They may damage the surface of the 
appliance and can create a risk of fi re.
Do not spray the refrigerator with water 
while it is plugged in, as it may cause an 
electric shock. 
Do not clean the refrigerator with benzene, 
thinner or car detergent for risk of fi re.
REPLACING THE INTERIOR 
LIGHT
For LED lamp, please contact service engineer 
to replace it.
WARNING
CAUTION