Samsung Rsh1ntrs User Manual

							
setting up _11
01 sEtting uP



1
setting up your side-by-side 
refrigerator
2. Removing the freezer door
A few things to mention first.•  Make sure that you lift the door straight up so the hinges are not\
 bent or broken.•  Be careful not to pinch the water tubing and wire harness on the door.•  Place doors on a protected surface to prevent scratching or damage\
.
1.  With the Freezer door closed, remove the upper hinge cover 1 using a screwdriver, and then disconnect the wires by gently pulling them apart  .


Be careful not to pinch the water tubing and wire harness on the door.
2.  Remove hinge screws  and the ground screw  by turning counter-clockwise, and take off the upper hinge . Be careful that the door does not fall on you as you are removing it 
3. Next, remove the door from the lower hinge  by carefully lifting the door straight up .
4. Remove the lower hinge  using a hex wrench.

DA99-01584A(HM-P)-EN(0.1).indd   112007.10.4   5:20:27 PM
   
						

							
1_ setting up

3.   Remove the door from the lower hinge  by lifting the door straight up .
Removing the Fridge Door
1. With the door closed, remove the upper hinge cover 1 using a screwdriver.
2.   Remove hinge screws  and the ground screw  by turning counter-clockwise, and take off the upper hinge . Be careful that the door does not fall on you as you are removing it



1
4.  Remove the lower hinge  from the bracket  by gently lifting the lower hinge upwards.

DA99-01584A(HM-P)-EN(0.1).indd   122007.10.4   5:20:29 PM
  
						

							
setting up _1
01 sEtting uP

setting up your side-by-side 
refrigerator
rEattaCHing tHE rEfrigErator Doors
Once you have safely placed your refrigerator where you plan for it to s\
tay, it is time to put the doors back on.
Reattaching the Freezer Door
1.  Replace the freezer door by inserting the water line 1 back into the lower corner of the door and then into the hole on the lower hinge . Gently pull the water line back down so that it runs straight, with no k\
inks or bends.
2.  Insert the upper hinge shaft  into the hole on the corner of the freezer door . Make sure the hinge is level between the upper hinge hole  and the  hole of the cabinet  and reattach the hinge screws  and ground screw  by turning in a clockwise direction.
3. Reconnect the wires.
4.  Place the front part of the upper hinge cover    on the front of the upper hinge 10 and reattach with the screw.
1

10







DA99-01584A(HM-P)-EN(0.1).indd   132007.10.4   5:20:30 PM
 
						

							
1_ setting up

Reattaching the Fridge Door
1.  Insert the lower hinge 1 back into the lower hinge bracket .
2.  Fit the hole in the corner of the fridge door  over the lower hinge .
3.    Insert the upper hinge shaft  into the hole on the hinge . Make sure the hinge is level between the upper hinge hole  and the hole on the top of the cabinet . Then, reattach hinge screws  and the ground screw 10 by turning it in a clock wise direction.
4.    Place the front part of the upper hinge cover  11 on the front of the upper hinge 1 and reattach it with the screw.
1



1
11

DA99-01584A(HM-P)-EN(0.1).indd   142007.10.4   5:20:31 PM
  
						

							
setting up _1

setting up your side-by-side 
refrigerator
Reattaching the Water Supply Line
1. Insert the water line 1 into the coupler .
Reattaching the Front Leg Cover
Before attaching the cover, check water connector for leakage.Replace the front leg cover by turning the three screws clockwise, as sh\
own in the figure.
01 sEtting uP
front Leg Cover
screw

1

DA99-01584A(HM-P)-EN(0.1).indd   152007.10.4   5:20:32 PM
      
						

							
1_ setting up

screw Driver
Leg
Legscrew Driver
LEVELing tHE rEfrigErator
Now that the doors are back on the refrigerator, you will want to make s\
ure the refrigerator is level so you can then make final adjustments. If the refrigerator is not level, it will\
 not be possible to get the doors perfectly even.
The front of the refrigerator is also adjustable.
When the Freezer door is lower than the fridge
Insert a flat-blade screwdriver into a notch on the Leg, turn it clock\
wise or counter clockwise tolevel the freezer.turning the three screws counter-clockwise.
When the Freezer door is higher than the fridgeInsert a flat-blade screwdriver into a notch on the Leg, turn it clock\
wise or counter clockwise tolevel the fridge.
Refer to the next section for the best way to make very minor adjustment\
s to the doors.

DA99-01584A(HM-P)-EN(0.1).indd   162007.10.4   5:20:33 PM
   
						

							
setting up _1
01 sEtting uP

In the case of the process to correct the imbalance is the same. Open th\
e doors and adjust them, one at a time, as follows:1.	 Unscrew the nut 1 from the lower hinge until it reaches the upper end of the bolt .
When you release the nut 1, make sure that you use the Allen wrench provided  to loosen the bolt  in a counter-clockwise direction. You should then be able to unscrew th\
e nut 1 with your fingers.
.	  Adjust the height difference between the doors by turning the bolt  clockwise  or counter clockwise .
When you turn clockwise , the door will move up.


1
Wrench
Bolt
Nut


Wrench
Bolt
setting up your side-by-side 
refrigerator
MaKing Minor aDJustMEnts to tHE Doors
Remember, a leveling refrigerator is necessary for getting the doors per\
fectly even. If you need help, review the previous section on leveling the refrigerator.
adjustment part
When the door of the freezer is higher than the fridge

DA99-01584A(HM-P)-EN(0.1).indd   172007.10.4   5:20:34 PM
   
						

							
1_ setting up

3.   After adjusting the doors, turn the nut 1 clockwise  until it reaches the lower end of the bolt, then tighten the bolt again with the wrench  to fix the nut in place 1.
If you do not secure the nut firmly, the bolt may release.
Close	MainWater	pipe
Close	MainWater	pipe
NO	GAp


1
Wrench
Bolt
Nut
CHECKing tHE watEr DisPEnsEr LinE (oPtionaL)
A water dispenser is just one of the helpful features on your new Samsun\
g refrigerator. To help promote better health, the Samsung water filter removes unwanted particles from your \
water. However, it does not sterilize or destroy microorganisms. You will need to purchase a water purifying s\
ystem to do that. In order for the icemaker to operate properly, water pressure of 138 ~862 Kpa is required\
. Under normal conditions, a 170 cc paper cup can be filled in 10 seconds. If the refrigerator is installe\
d in an area with low water pressure (below 138 Kpa), you can install a booster pump to compensate for the low pres\
sure. Make sure the water storage tank inside the refrigerator is properly filled. To do this, press the\
 water dispenser lever until the water runs from the water outlet.  
Water Line installation Kits are included with unit. You can find it i\
n freezer drawer.
instaLLing tHE watEr DisPEnsEr LinE
For	Interior	model
Parts for water line Installation
	1		Water	line	fixer	and	screws		pipe	connector			Water	line			Water	Filter
Connecting to the water supply line1. first, shut off the main water supply line.2. locate the nearest cold, drinking water line.3. follow the Water line Installation Instructions in the     installation kit.
CAUTION
The water line must be connectedto the cold water pipe. If it is connected to the hot water pipe, it may cause thepurifier to malfunction.
4.  After connecting the water supply to the water filter, turn your main \
water supply back on and dispense about 1l to clear and prime the water filter.

DA99-01584A(HM-P)-EN(0.1).indd   182007.10.4   5:20:36 PM
   
						

							
CAUTION
01 sEtting uP
setting up your side-by-side 
refrigerator
Connecting the water line to the refrigerator1.  Remove the cap from water line on the unit and insert compression nut to the water \
line on the unit after disassembling from provided water line.2. Connect both water line from the unit and water line provided kit.3. Tighten the compression nut onto the compression fitting. Be carefu\
l no gap between two items.4. Turn water on and check for any leakage.
Only connect the water line to a drinkable water source.If you have to repair or disassemble the water line, cut off 6.5mm of th\
e plastic tubing tomake sure you get a snug, leak-free connection.  
Before being used, the leakage in these places should be examined
•    Samsung Warranty does not cover WATER LINE INSTALLATION.•    It’ll be done at customer’s charge except the retail price includes installation cost.•   Please contact Plumber or Authorized Installer for the installation if needed.•  If Water leakage happened due to improper installation, Please con\
tact installer.
Remove	cap
Water	Linefrom	unit
Water	Linefrom	Kit
No	gap
Loosen	a
Installing the water filter.
1.   Remove the water filter from the box and put a replacement indicator sticker on the filter as shown.2.  Place a sticker on the filter that dates six months in the future. For example, if you install the water filter in March, put the “SEP” sticker on the filter to remind you to replace in \
September. That way you’ll know when it is time to replace the filter. Normally filter life is about 6 months.3.  Next, remove the fixed cap by turning it counter clockwise. Keep the cap in a safe place for use if you choose not to use a filter.4.  Remove the filter’s protective cap and then position and insert the filter into the filter housing.5.  Slowly turn the water filter clockwise 90º to align with the indication mark on the cover, locking the filter in position. Make sure that the indicator is lined up with the “lock” position. Remember, do not over-tighten.   
If your model contains wine shelf, you should remove the wine shelf before installing waterfilters.
setting up _1
sticker(Month indication)


1
Cover filter
align the indicationmark with lock positionseparationof red cap

DA99-01584A(HM-P)-EN(0.1).indd   192007.10.4   5:20:39 PM
  
						

							
Replacement Instructions
1. Shut off water supply.2. Note the Flow direction on the filter.3. Insert water supply tube into the inlet side of the filter until th\
e tube stop.
4. After inserting tube, put together the clip strongly. The Clip fix \
the tube.
5.  Turn on the water and check for leaks. If leaks occur, repeat step 1,2,3\
,4. If leaks persist, discontinue use and call your supporting dealer.6. Flush filter for 5 minutes before use.
0_ setting up
instaLLing tHE watEr DisPEnsEr LinE
For	Exterior	model
Parts for water line Installation 
Connecting to the water supply line
Connect the water pipe with coupler and tap.1. Close the main water tap.2. Connect coupler “A” to the tap.
CAUTION
The water line must be connected to the cold water pipe. If it is connected to the hot water pipe, it may cause the purifier to malfunction.
Water	line	fixer	and	screwspipeconnectorWater	linepurifierpurifier	lock-clip
WARRANTY INFORMATION
This water line installation is not covered by the refrigerator or ice maker manufacturer’s warranty.Follow these instructions carefully to minimise the risk of expensive water damage.
Note:If the coupler does not fit on the current tap, gothe nearest authorised service dealer and purchase the right couplers fittings.
COUPLER “A”
TAP
COUPLER
SIDE OFPURIFIER
WATER INLETSIDE OF PURIFIER
LINE OUTLET
90 degree
PURIFIER WATER
select the location where the purifier is to install. (Model with the purifier)
-    If you wish to reassemble the water inlet and outlet sides of the purifier during purifier installation, see the reference illustration.-     Cut the water line attached to the purifier to the appropriate place after measuring the distance between the purifier and the cold water tap.
WATER SUPPLYINLET SIDEPERMEAT
FLOW DIRECTION
Note	:		You must also ensure that the cut is square and not at any sort of angle as this could cause a leak
CAUTION
Locking Clip
Insert  Locking  Clip  After tube seated

DA99-01584A(HM-P)-EN(0.1).indd   202007.10.4   5:20:41 PM