Samsung Rsh1ftrs User Manual

setting up _11
01 sEtting uP



1
setting up your side-by-side 
refrigerator
2. Removing the freezer door
A few things to mention first.•  Make sure that you lift the door straight up so the hinges are not\
 bent or broken.•  Be careful not to pinch the water tubing and wire harness on the door.•  Place doors on a protected surface to prevent scratching or damage\
.
1.  With the Freezer door closed, remove the upper hinge cover 1 using a screwdriver, and then disconnect the wires by...

1_ setting up

3.   Remove the door from the lower hinge  by lifting the door straight up .
Removing the Fridge Door
1. With the door closed, remove the upper hinge cover 1 using a screwdriver.
2.   Remove hinge screws  and the ground screw  by turning counter-clockwise, and take off the upper hinge . Be careful that the door does not fall on you as you are removing it



1
4.  Remove the lower hinge  from the bracket  by gently lifting the lower...

setting up _1
01 sEtting uP

setting up your side-by-side 
refrigerator
rEattaCHing tHE rEfrigErator Doors
Once you have safely placed your refrigerator where you plan for it to s\
tay, it is time to put the doors back on.
Reattaching the Freezer Door
1.  Replace the freezer door by inserting the water line 1 back into the lower corner of the door and then into the hole on the lower hinge . Gently pull the water line back down so that it runs straight, with no k\
inks or bends.
2.  Insert the...

1_ setting up

Reattaching the Fridge Door
1.  Insert the lower hinge 1 back into the lower hinge bracket .
2.  Fit the hole in the corner of the fridge door  over the lower hinge .
3.    Insert the upper hinge shaft  into the hole on the hinge . Make sure the hinge is level between the upper hinge hole  and the hole on the top of the cabinet . Then, reattach hinge screws  and the ground screw 10 by turning it in a clock wise direction.
4.    Place the front...

setting up _1

setting up your side-by-side 
refrigerator
Reattaching the Water Supply Line
1. Insert the water line 1 into the coupler .
Reattaching the Front Leg Cover
Before attaching the cover, check water connector for leakage.Replace the front leg cover by turning the three screws clockwise, as sh\
own in the figure.
01 sEtting uP
front Leg Cover
screw

1

DA99-01584A(HM-P)-EN(0.1).indd   152007.10.4   5:20:32 PM
      

1_ setting up

screw Driver
Leg
Legscrew Driver
LEVELing tHE rEfrigErator
Now that the doors are back on the refrigerator, you will want to make s\
ure the refrigerator is level so you can then make final adjustments. If the refrigerator is not level, it will\
 not be possible to get the doors perfectly even.
The front of the refrigerator is also adjustable.
When the Freezer door is lower than the fridge
Insert a flat-blade screwdriver into a notch on the Leg, turn it clock\
wise or counter...

setting up _1
01 sEtting uP

In the case of the process to correct the imbalance is the same. Open th\
e doors and adjust them, one at a time, as follows:1.	 Unscrew the nut 1 from the lower hinge until it reaches the upper end of the bolt .
When you release the nut 1, make sure that you use the Allen wrench provided  to loosen the bolt  in a counter-clockwise direction. You should then be able to unscrew th\
e nut 1 with your fingers.
.	  Adjust the height difference between...

1_ setting up

3.   After adjusting the doors, turn the nut 1 clockwise  until it reaches the lower end of the bolt, then tighten the bolt again with the wrench  to fix the nut in place 1.
If you do not secure the nut firmly, the bolt may release.
Close	MainWater	pipe
Close	MainWater	pipe
NO	GAp


1
Wrench
Bolt
Nut
CHECKing tHE watEr DisPEnsEr LinE (oPtionaL)
A water dispenser is just one of the helpful features on your new Samsun\
g refrigerator. To help promote better health, the...

CAUTION
01 sEtting uP
setting up your side-by-side 
refrigerator
Connecting the water line to the refrigerator1.  Remove the cap from water line on the unit and insert compression nut to the water \
line on the unit after disassembling from provided water line.2. Connect both water line from the unit and water line provided kit.3. Tighten the compression nut onto the compression fitting. Be carefu\
l no gap between two items.4. Turn water on and check for any leakage.
Only connect the water line to a...

Replacement Instructions
1. Shut off water supply.2. Note the Flow direction on the filter.3. Insert water supply tube into the inlet side of the filter until th\
e tube stop.
4. After inserting tube, put together the clip strongly. The Clip fix \
the tube.
5.  Turn on the water and check for leaks. If leaks occur, repeat step 1,2,3\
,4. If leaks persist, discontinue use and call your supporting dealer.6. Flush filter for 5 minutes before use.
0_ setting up
instaLLing tHE watEr DisPEnsEr LinE
For...