Samsung Rsa1nhmh User Manual

							
setting up _11

setting up your side-by-side 
refrigerator
2. Removing the freezer door
A few things to mention first.
•	Make sure that you lift the door straight up so the hinges are not bent or broken.
•	Be careful not to pinch the water tubing and wire harness on the door.
•	Place doors on a protected surface to prevent scratching or damage.
1.	With the Freezer door closed, remove the upper hinge cover 1 using a screwdriver, and 
then disconnect the wires by gently pulling them apart .
.	
Remove hinge screws  and the ground screw  by turning counter-clockwise, and take 
off the upper hinge . Be careful that the door does not fall on you as you are removing it
.	
Next, remove the door from the lower hinge  by carefully lifting the door straight up .






1
01 sEtting uP
Be careful not to pinch 
the water tubing and 
wire harness on the 
door.
   
						

							
1_ setting up

Removing the Fridge Door
1.	With the door closed, remove the upper hinge cover 1 using a screwdriver.
.	
Remove hinge screws  and the ground screw  by turning counter-clockwise, and take 
off the upper hinge . Be careful that the door does not fall on you as you are removing it.
.	
Remove the door from the lower hinge  by lifting the door straight up .
1



downloaded	from	fridge-Manual.com	Manuals  
						

							
setting up _1

setting up your side-by-side 
refrigerator
rEattaCHing tHE rEfrigErator Doors
Once you have safely placed your refrigerator where you plan for it to stay, it is time to put the doors back on.
Reattaching the Freezer Door
1.   Insert the upper hinge shaft  into the hole on the corner 
of the freezer door . Make sure the hinge is level between 
the upper hinge hole  and the  hole of the cabinet  and 
reattach the hinge screws  and ground screw  by turning 
in a clockwise direction. 
 
 
.	
Reconnect the wires. 
 
.	
Place the front part of the upper hinge cover   
 on the front of the upper hinge 10 and 
reattach with the screw.
01 sEtting uP
10






downloaded	from	fridge-Manual.com	Manuals 
						

							
1_ setting up

Reattaching the Fridge Door
1.  Fit the hole in the corner of the fridge door  over  the lower 
hinge .
.	
Insert the upper hinge shaft  into the hole on the hinge 
. Make sure the hinge is level between the upper hinge 
hole  and the hole on the top of the cabinet . Then, 
reattach hinge screws  and the ground screw 10 by 
turning it in a clock wise direction.
.	
Place the front part of the upper hinge cover  
11 on the front of the upper hinge 1 and 
reattach it with the screw.


1
11
downloaded	from	fridge-Manual.com	Manuals 
						

							
setting up _1

setting up your side-by-side 
refrigerator
Reattaching the Water Supply Line
1.	Insert the water line 1 into the coupler .
Reattaching the Front Leg Cover
Before attaching the cover, check water connector for leakage. 
Replace the front leg cover by turning the three screws clockwise, as shown in the figure.
front Leg Cover
screw

1
01 sEtting uP
 from fridge-Manual.com Manuals      
						

							
1_ setting up

LEVELing tHE rEfrigErator
Now that the doors are back on the refrigerator, you will want to make sure the refrigerator is level so 
you can then make final adjustments. If the refrigerator is not level, it will not be possible to get the doors 
perfectly even.
The front of the refrigerator is also adjustable.
When the Freezer door is lower than the fridge
Insert a flat-blade screwdriver into a notch on the Leg, turn it clockwise or counter clockwise to 
level the freezer.
When the Freezer door is higher than the fridge
Insert a flat-blade screwdriver into a notch on the Leg, turn it clockwise or counter clockwise to 
level the fridge.
Refer to the next section for the best way to make very minor adjustment\
s to the doors.
Leg
Leg
screw Driver
screw Driver
 from fridge-Manual.com Manuals   
						

							
setting up _1

setting up your side-by-side 
refrigerator
MaKing Minor aDjustMEnts to tHE Doors
Remember, a leveling refrigerator is necessary for getting the doors perfectly even. If you need help, 
review the previous section on leveling the refrigerator.When	the	door	of	the	freezer	is	higher	
than	the	fridge
In the case of the process to correct the imbalance is the same. Open the doors and adjust 
them, one at a time, as follows:
1.	Unscrew the nut 1 from the lower hinge until it reaches the upper end of the bolt .
When you release the nut 1, make sure that you use the Allen wrench provided  to 
loosen the bolt  in a counter-clockwise direction. You should then be able to unscrew the 
nut 1 with your fingers.
.	
Adjust the height difference between the doors by turning the bolt  clockwise  or 
counter clockwise .
When you turn clockwise , the door will move up.
adjustment part


1
Wrench bolt
Nut


Wrench
bolt
01 sEtting uP
 from fridge-Manual.com Manuals   
						

							1_ setting up
.	After adjusting the doors, turn the nut 1 clockwise  until it reaches the lower end of 
the bolt, then tighten the bolt again with the wrench  to fix the nut in place 1.
If you do not secure the nut firmly, the bolt may release.
CHECKing tHE watEr DisPEnsEr LinE (oPtionaL)
A water dispenser is just one of the helpful features on your new Samsung refrigerator. To help promote 
better health, the Samsung water filter removes unwanted particles from your water. However, it does not 
sterilize or destroy microorganisms. You will need to purchase a water purifying system to do that.
In order for the icemaker to operate properly, water pressure of 138 ~862 Kpa is required. Under normal 
conditions, a 170 cc paper cup can be filled in 10 seconds.
If the refrigerator is installed in an area with low water pressure (below 138 Kpa), you can install a booster 
pump to compensate for the low pressure.
Make sure the water storage tank inside the refrigerator is properly filled. To do this, press the water 
dispenser lever until the water runs from the water outlet.
Water Line installation Kits are included with unit. You can find it in freezer drawer.
instaLLing tHE watEr DisPEnsEr LinE
Parts for water line Installation
Connecting to the water supply line
Connect	the	water	pipe	with	coupler	and	tap.
1.	Close	the	main	water	tap.
.	Connect	coupler	“A”	to	the	tap.	Note:
Water	line	fixer	
and	screwsPipeconnector Water	line	Filter

lock-clip	
 Filter


1
Wrench
bolt
Nut
CAUTION
The water line must be connectedto the cold water pipe.If it is connected to the hotwater pipe, it may cause thefilter to malfunction.
WARRANTY INFORMATION
This water line installation is not covered by the refrigerator or ice maker manufacturer’s warranty.Follow these instructions carefully to minimise the risk of expensive water damage.
Note:
If the coupler does not fit on the current tap, gothe nearest authorised service dealer and purchase the right couplers fittings.
COUPLER “A”
TAP
   
						

							setting up _1
Remove any residual matter inside the filter. (Model with the filter)
-  Open the main water tap to check whether 
water is running through the water tube on 
the water inlet side of the filter.
-   If water does not come out through the line, 
check whether the tap is open.
-   Leave the tap open until clean water is 
running out and any residual matter that built 
up during manufacturing has been removed.
Attach the filter lock stations.
-  Hold the filter lock stations in the appropriate 
position (under the sink for example) and fix it tightly 
into place where to screw.
Secure the filter in position.
-  Fix the filter in position, as shown in the 
figure on the right.
setting up your side-by-side 
refrigerator
01 sEtting uP
select the location where the filter is to 
install. (Model with the filter)
-   If you wish to reassemble the water inlet and out
-
let sides of the filter during filter installation, 
see the reference illustration.
-   Cut the water line attached to the filter to the 
appropriate place after measuring the distance 
between the filter and the cold water tap.
COUPLER
SIDE OF
FILTER
WATER INLETSIDE OF FILTER
LINE OUTLET
90 degree
FILTER WATERREFERENCE
WATER LINE FILTERWATER
OUTLET SIDEOF FILTER
TWO FILTER LOCKSTATION
TWO FILTER LOCKSTATION
TIGHTENINGBAND
FILTER
WATER TUBE
FILTER
LOCK STATIONS
 
						

							
0_ setting up
Connect the water line to the refrigerator.
- Remove the compressor cover of the refrigerator.
-  Connect the water line to the valve, as shown in the 
figure.
-   When connected, check if there is any leakage.            
If any, repeat the connection.
- Reattach the compressor cover of the refrigerator.
Secure the water line.
-  Using clip ”A”, fix the water line to the wall (the back of 
refrigerator).
-   When the water line is secure, make sure whether the water line 
is not excessively bent, pinched or squashed.
CLIP A
WATER LINE
WATER LINE
INSTRUCTIONSCOMPRESSOR COVER OFREFRIGERATOR
CONNECTION NUT