Samsung Rs E8kpas Oweners Manual

							20
REMOVING THE FRONT LEG COVER
1) Remove the water tube by pressing the coupler (➁) and pulling the water tube (➀) away. Open the freezer and refrigerator doors, and then take off the front leg cover assembly by turning
the three screws counter-clockwise.
aFRONT LEG COVER
SCREW
Removing the Front Leg Cover 
Separating the water supply line from the refrigerator
Do not cut the water tube but separate it from the coupler.WARNING
 
						

							21
INSTALLATION INSTRUCTIONS
REMOVING THE REFRIGERATOR DOORS
1) With the door closed, remove the Top table (➀) using a screwdriver, and then disconnect
the wires (➁).
2) Remove hinge screws (➂) and ground screw (➃) counter-clockwise, and take off the upper hinge (➄) along the  
arrow (➅). Take care when removing the door to ensure that it does not fall on you.
3) Remove the door from the lower hinge (	) by carefully lifting the door (➇).
Removing the Freezer Door
• Lift the door straight up.
• Be careful not to pinch the water tubing and wire harness on the door.
• Place doors on a protected surface.
NOTE
 
						

							22
REMOVING THE REFRIGERATOR DOORS
1) Disconnect the wires (➀).
2) Remove hinge screws (➁) and ground screw (➂) counter-clockwise, and take off the upper  hinge (➃) in the    
direction of the arrow (➄). Take care when removing the door to ensure that it does not fall on you.
3) Remove the door from the lower hinge (➅) by
lifting the door (➆).4) Remove the lower hinge (➇) from the bracket
lower hinge (➈) by lifting the lower hinge (
➇)
in the direction of the arrow.
Removing the Refrigerator Door
NOTE
• After disassembling the freezer / refrigerator door, move it to the appropriate location. you must reassemble it.
 
						

							23
INSTALLATION INSTRUCTIONS
REATTACHING THE REFRIGERATOR DOORS
Reattaching the Freezer Door
1) Reattach the freezer door by inserting the hose (
➀) in the lower side of the door into the hole in the lower
hinge (➁) and pull the hose down.
2) Insert the upper hinge shaft (➂) into the hole (➃). After levelling  the upper hinge hole (➄) with the hole of the
cabinet (➅). Fasten bolts (➆) and screw (
➇) in a clockwise direction.
3) Connect the wires.  4) Put the front part of the Top table (➈) on the front
part of the upper hinge (➉) and reattach from the
front part of the Top table first.
 
						

							24
REATTACHING THE REFRIGERATOR DOORS
Reattaching the Refrigerator Door
1) Insert the lower hinge (➀) in the bracket
lower hinge (➁).2) Place the hole in the refrigerator door (➂)
over the lower hinge (➃).
3) Insert the upper hinge shaft (➄) into the hole (➅). After levelling  the upper hinge hole (➆)
with the hole of the cabinet (
➇). Fasten  hinge screws (➈) and screw (➉) in the clockwise direction.
4) Connect the wires.  5) Put the front part of the Top table (    ) on the front 
part of the upper hinge (    ) and reattach it from
the front part of the Top table first.
11
12
 
						

							25
INSTALLATION INSTRUCTIONS
REATTACHING THE REFRIGERATOR DOORS
FRONT LEG COVER
SCREW
1) While pressing the front face of coupler (➁), insert the water line (➀) in the coupler.
Put on the front leg cover by turning the three screws clockwise, as shown in the figure.
Reattaching the Water Tube 
Reattaching the Front Leg Cover (Optional)
 
						

							26
ADJUSTING THE CLEARANCE BETWEEN THE DOORS
The doors will be uneven if the refrigerator is not level.
Case 1) Freezer door is lower than
that of the refrigeratorInsert a straight screwdriver (-) () into a
slot of the control lever (➁), turn it clockwise
and level the refrigerator.
Case 2) Freezer door is higher than
that of the refrigeratorInsert a straight screwdriver (-) () into a
slot of the control lever (➁), turn it clockwise 
and level the refrigerator.
Do not make small adjustment by turning the control lever, Please refer to the next page.
DIFFERANCE  OF HEIGHT DIFFERANCE  OF HEIGHT
➀DRIVER(-)
➀DRIVER(-)
➁CONTROL LEVER
➁CONTROL LEVER
Please level the refrigerator first.
NOTE
 
						

							27
INSTALLATION INSTRUCTIONS
ADJUST THE CLEARANCE BETWEEN THE DOORS
Making small adjustments between doors.
If the door of freezer is higher or lower than that of the refrigerator.
3) After adjusting the doors, turn the nut () clockwise(            ) until the lower end of the bolt,  then tighten the
bolt again with the wrench (➂) to fix the nut().
If you do not fix the nut (
)firmly, the bolt (
➁) may be released. 
2)  Please adjust the height difference between the doors turning the bolt (➁) clockwise(          ) or counter
clockwise (          ).
When you turn clockwise ( ),  the door goes up.
➂WRENCH
➀NUT ➁BOLT
➀NUT➁BOLT➂WRENCH
➂WRENCH➁BOLT
Please open the doors and adjust the doors as follows:
1) Release the nut () on the lower hinge  until the upper end of the bolt (➁).
When you release the nut(), use enclosed hex wrench (➂) to turn the bolt(➁) a little 
counter 
clockwise. Loosen the nut() with your finger.NOTE
NOTE
NOTE
➀NUT
Adjustment part
 
						

							28
CHECKING THE WATER DISPENSER LINE (OPTIONAL)
INSTALLING OF THE WATER DISPENSER LINE
Checking the Parts
1) In order to operate the ice maker properly, water pressure of 1.4 ~ 10 kgf/cm2 (0.14 ~ 9.8Mpa, 
19.9 ~ 142.2 psi, 1.37 ~ 9.8 bars)  is required.
In this range a 100 cc paper cup can be filled in 10 seconds.
2) The water filter removes particles. It does not sterilize or destroy any micro-organisms.
3) If the refrigerator is installed in an area with low water pressure (below 1.4kgf/cm
2 , 0.14 Mpa, 
19.9 psi,1.37bars), you should install a booster pump to compensate for the low pressure.
4) Ensure the water storage tank inside the refrigerator is properly filled initially. Push the water dis
penser lever until the water runs from the outlet.
Connecting to water supply line
- Shut off the main water supply line and turn the Ice 
maker to the off position.
- Locate the nearest cold drinking water line.
- Follow the instructions in the ice maker installation kit.
(Case 1)
1. Cold Water line
2. Pipe Clamp.
3.Copper (or Plastic) line
4.Compression Nut
5.Compression Sleeve
6.Shut Off Valve
7.Packing Nut.
NOTE
A universal water supply kit is available at extra cost from your dealer. The refrigerator manufacturer
recommends using a water supply kit containing copper tubing.
Purifier Valve water fitting
Clip A x 12EA Water line
Tapping screw x 12EA
(Connector Water Filter Assy)
Sealing tape
 
						

							29
INSTALLATION INSTRUCTIONS
INSTALLING OF THE WATER DISPENSER LINE
WARRANTY INFORMATION
This water line installation is not covered by the refriger-ator
or ice maker manufacturers warranty.
Follow these instructions carefully to minimise the risk of
expensive water damage.
Note:
If the coupler does not fit on the current tap, go
the nearest authorised service dealer and purchase
the right couplers fittings.
- Slip the compression nut and plastic ferrule
through the plastic tube.
- After inserting the sleeve, tighten the compres-sion
nut onto 1/4” compression fitting(union).
Connect the water line to the refrigerator
Check the water supply line
Waterline must be connected to drinkable water onlyNOTEDo not overtighten the compression nut.
NOTE
- Slip the compression ferrule and nut on copper(or plastic) tubing as 
shown.
Tighten the comperssion nut onto the com-pression fitting(union).
- Turn water on and check for any leakege.
Connect the water pipe with coupler and tap.
- Close the main water tap.
- Connect coupler “A” to the tap.
- Every join should be protected with sealing tape.Compression
Nut
Sleeve
Compression
fitting
Ferrule
Ferrule
Compressi
on Nut
(Case 2)
COUPLER “A”
TAP
CAUTION
The water line must be connect-ed
to the cold water pipe.
If it is connected to the hot water
pipe, it may cause the
purifier to malfunction.