Samsung Rs 21 Hnlmr User Manual
Have a look at the manual Samsung Rs 21 Hnlmr User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1705 Samsung manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
setting up _11 01 SETTING UP 4. After connecting the water supply to the water fi lter, turn your main water supply back on and dispense about 1l to clear and prime the water fi lter. Connecting the water line to the refrigerator 1. Remove the dust cap from the water line on the rear of the unit and fi t a compression nut from the install kit. 2. Remove the water pipe from the install kit and fi t a compression nut to one end. 3. Join the two pipes together using the compression joint from the install kit ensuring that the joint is water tight. 4. Join the other end of the install pipe to the main water supply and turn on the water to check for leaks. Only connect the water line to a drinkable water source. If you have to repair or disassemble the water line, cut off 6.5mm of the plastic tubing to make sure you get a snug, leak-free connection. Before being used, the leakage in these places should be examined CHECKING THE WATER DISPENSER LINE (OPTIONAL) A water dispenser is just one of the helpful features on your new Samsung refrigerator. To help promote better health, the Samsung water fi lter removes unwanted particles from your water. However, it does not sterilize or destroy microorganisms. You will need to purchase a water purifying system to do that. In order for the icemaker to operate properly, water pressure of 138 ~862 Kpa is required. Under normal conditions, a 170 cc paper cup can be fi lled in 10 seconds. If the refrigerator is installed in an area with low water pressure (below 138 Kpa), you can install a booster pump to compensate for the low pressure. Make sure the water storage tank inside the refrigerator is properly fi lled. To do this, press the water dispenser lever until the water runs from the water outlet. Water Line installation Kits are included. You can fi nd it in one of the freezer drawers. INSTALLING THE WATER DISPENSER LINE For Interior model Parts for water line Installation Connecting to the water supply line 1. First, shut off the main water supply line. 2. Locate the nearest cold, drinking water line. 3. Follow the water line installation instructions in the installation kit. 1 Water line fi xer and screws Water line fi xer and screws 2 Pipe connector Pipe connector 3 Water line Water line 4 Water Filter Water Filter CAUTION The water line must be connected to the cold water pipe. If it is connected to the hot water pipe, it may cause the purifi er to malfunction. Close MainClose MainWater pipeWater pipe Close MainClose MainWater pipeWater pipeNo gapNo gap RemoveRemove capcap Water LineWater Linefrom unitfrom unit Water LineWater Linefrom Kitfrom Kit No gapNo gap Loosen aLoosen a CAUTION % JOEC% JOEC1.1.
12_ setting up INSTALLING THE WATER DISPENSER LINE For Exterior model Parts for water line Installation Connecting to the water supply line Connect the water pipe with coupler and tap. 1. Close the main water tap. 2. Connect coupler “A” to the tap. Select the location where the purifi er is to install. (Model with the purifi er) - If you wish to reassemble the water inlet and outlet sides of the purifi er during purifi er installation, see the reference illustration. - Cut the water line attached to the purifi er to the appropriate place after measuring the distance between the purifi er and the cold water tap. • Samsung Warranty does not cover WATER LINE INSTALLATION. • The cost of connection to a water supply is at the customer expense, unless included in the delivery charge (refer to the delivery agreement with the seller) • Please contact Plumber or Authorised Installer for the installation if needed. • If Water leakage occurs due to improper installation, Please contact installer. Water line fi xer and screwsWater line fi xer and screwsPipe connectorPipe connector Water lineWater linePurifi er lock-clipPurifi er lock-clipPurifi erPurifi er CAUTION The water line must be connected to the cold water pipe. If it is connected to the hot water pipe, it may cause the purifi er to malfunction. WARRANTY INFORMATION This water line installation is not covered by the refrigerator or ice maker manufacturer’s warranty. Follow these instructions carefully to minimise the risk of expensive water damage. Note: If the coupler does not fi t on the current tap, go the nearest authorised service dealer and purchase the right couplers fi ttings. % JOEC% JOEC1.1.
setting up _13 01 SETTING UP Remove any residual matter inside the purifi er. (Model with the purifi er) - Open the main water tap to check whether water is running through the water tube on the water inlet side of the purifi er. - If water does not come out through the line, check whether the tap is open. - Leave the tap open until clean water is running out and any residual matter that built up during manufacturing has been removed. Attach the purifi er lock-clip. - Hold the purifi er lock-clip in the appropriate position (under the sink for example) and fi x it tightly into place where to screw. Secure the purifi er in position. - Fix the purifi er in position, as shown in the fi gure on the right. Replacement Instructions 1. Shut off water supply. 2. Note the Flow direction on the fi lter. 3. Insert water supply tube into the inlet side of the fi lter until the tube stop. 4. After inserting tube, put together the clip strongly. The Clip fi x the tube. 5. Turn on the water and check for leaks. If leaks occur, repeat step 1,2,3,4. If leaks persist, discontinue use and call your supporting dealer. 6. Flush fi lter for 5 minutes before use. COUPLER “A”COUPLER “A” TAPTA P COUPLERCOUPLER SIDE OF SIDE OF PURIFIERPURIFIER WATER INLETWATER INLETSIDE OF PURIFIERSIDE OF PURIFIER LINE OUTLETLINE OUTLET 90 degree90 degree PURIFIER WATERPURIFIER WATERCAUTION Locking ClipLocking Clip Insert Locking Clip After Insert Locking Clip After tube seatedtube seated WATER SUPPLYWATER SUPPLYINLET SIDEINLET SIDEPERMEATPERMEAT FLOW DIRECTIONFLOW DIRECTION Note : You must also ensure that the cut is square and not at any sort of angle as this could cause a leak WATER LINEWATER LINE PURIFIERPURIFIER WATERWATER OUTLET SIDE OF OUTLET SIDE OF PURIFIERPURIFIER PURIFIER LOCK-CLIPPURIFIER LOCK-CLIP WATER TUBEWATER TUBE PURIFIER LOCK-CLIPPURIFIER LOCK-CLIP PURIFIERPURIFIER % JOEC% JOEC1.1.
14_ setting up Check the amount of water supplied to the ice tray. 1. Lift up the icemaker cover and gently pull out. 2. When you press the Test button for 3 seconds, the ice cube container is fi lled with water from the water supply tap. Check to make sure the amount of water is correct (see the illustration below). If the water level is too low, the ice cubes will be small. This is a water pressure problem from with in the main water pipes, not the refrigerator. Using the anti-sweat heater switch When the humidity of the indoor is high, sweat may form around the beverage station & dispenser. Turn the Anti-sweat heater switch on, to remove the sweat and turn the switch off when the sweat disappears. Connect the water line to the refrigerator. - Remove the compressor cover of the refrigerator. - Connect the water line to the valve, as shown in the fi gure. - When connected, check if there is any leakage. If any, repeat the connection. - Reattach the compressor cover of the refrigerator. Secure the water line. - Using clip ”A”, fi x the water line to the wall (the back of refrigerator). - When the water line is secure, make sure whether the water line is not excessively bent, pinched or squashed. Removing any residual matter inside the water supply line after installing fi lter. 1. Turn ON the main water supply & turn OFF the valve to the water supply line. 2. Run water through the dispenser until the water runs clear (approx. 1L). This will clean the water supply system and remove air from the lines. 3. Additional fl ushing may be required in some households. 4. Open the refrigerator door and make sure there are no water leaks coming from the water fi lter. A newly installed water fi lter cartridge may cause water to briefl y spurt from the water dispenser. This is due to air getting into the line. It should pose no problem to operation. RS21/23H** (OPTIONAL) WATER LINEWATER LINE INSTRUCTIONS INSTRUCTIONS COMPRESSOR COVER OF COMPRESSOR COVER OF REFRIGERATORREFRIGERATOR CONNECTION NUTCONNECTION NUT CLIP ACLIP A WATER LINEWATER LINE Ice maker 1 Feeler Arm 2Test button Check the water level % JOEC% JOEC1.1.
operating _15 02 OPERATING OPERATING THE REFRIGERATOR Using the Control Panel / Digital Display When not in use the temperature display will turn off, this is normal. 1 POWER FREEZE BUTTON Speeds up the time needed to freeze products in the freezer. This can be helpful if you need to quickly freeze items that spoil easily or if the temperature in the freezer has warmed dramatically (For example, if the door was left open). 2 FREEZER BUTTON Press the Freezer button to set the freezer to your desired temperature, You can set the temperature between -14°C (8°F) and -25ºC (-14°F). 3 ICE TYPE BUTTON Use this button to choose Cubed, Crushed or to turn the Ice feature off. 4 FILTER CHANGE BUTTONWhen you change the fi lter, press this button for 3 seconds to reset the fi lter schedule. 5 POWER COOL BUTTON Press this button to quickly return the refrigerator to the set temperature. Press this button again to cancel the Power Cool mode. 6 CHILD LOCK FUNCTION By pressing the Power Cool button and the Fridge button simultaneously for 3 seconds, all buttons will be locked. The Water dispenser lever and the Ice lever will not work either. To cancel this function, Press these two buttons for 3 seconds again. 7 FRIDGE BUTTON Press the Fridge button to set the fridge to your desired temperature. You can set temperature between 1°C and 7°C (34°F and 45°F). When you use Power Freeze the energy consumption of the refrigerator will increase. Remember to turn it off when you don’t need it and return the freezer to your original temperature setting. If you need to freeze large amount of food stuff, activate Power Freeze function at least 24 hours before. operating the SAMSUNG side- by-side refrigerator 5 6 7 1 3 4 2 COOLSELECT MODEL DISPENSER MODEL NORMAL MODEL % JOEC% JOEC1.1.
16_ operating USING THE ICE AND COLD WATER DISPENSER Press the Ice Type button to select the type of ice you want Ice is made in cubes. When you select “Crushed”, the icemaker grinds the ice cubes into crushed ice. Dispensing ice Place your glass underneath the ice outlet and push gently against the ice dispenser lever with your glass. Make sure the glass is in line with the dispenser to prevent the ice from bouncing out. Using the Water Dispenser Place a glass underneath the water outlet and push gently against the water dispenser lever with your glass. Make sure the glass is in line with the dispenser to prevent the water from splashing out. CONTROLLING THE TEMPERATURE CONTROLLING THE FREEZER TEMPERATURE The freezer temperature can be set between -14°C (8°F) and -25ºC (-14°F) to suit your particular needs. Press the Freezer button repeatedly until the desired temperature is shown in the temperature display. Keep in mind that foods like ice cream may melt at -16ºC (4°F). The temperature display will move sequentially from -14°C (8°F) and -25ºC (-14°F). When the display reaches -14ºC (8°F), it will begin again at -25ºC (-14°F). Five seconds after the new temperature is set the display will again show the actual current freezer temperature. However, this number will change as the Freezer adjusts to the new temperature. CONTROLLING THE FRIDGE TEMPERATURE The refrigerator temperature can be set between 7ºC (46°F) and 1ºC (34°F) to suit your particular needs. Press the Fridge button repeatedly until the desired temperature is shown in the temperature display. The temperature control process for the Fridge works just like the Freezer process. Press the Fridge button to set your desired temperature. After a few seconds, the Fridge will begin tracking towards the newly set temperature. This will be refl ected in the digital display. The temperature of the freezer or the refrigerator may rise from opening the doors too frequently, or if a large amount of warm or hot food is placed in either side. This may cause the digital display to blink. Once the freezer and refrigerator return to their normal set temperatures the blinking will stop. If the blinking continues, you may need to “reset” the refrigerator. Try unplugging the appliance, wait about 10 minutes and then plug back in. No IceSelect this if you want to turn off the icemaker % JOEC% JOEC1.1.
operating _17 02 OPERATING USING THE COOLSELECT ZONE™ DRAWER (OPTIONAL) Quick Cool • You can use the Quick Cool feature with the CoolSelect Zone™. • “Quick Cool” allows 1~3 canned beverages to cool within 60 min. • To cancel this function, press the “Quick Cool” button again. CoolSelect Zone™ returns to the previous temperature. • When “Quick Cool” ends, it returns to the “Cool” temperature setting. Thaw • Drips loss and quality deterioration of meats reduces the freshness of foods. • After “Thaw” is selected, warm and cold air is alternately supplied into the CoolSelect Zone™ Drawer. • Depending on the weight of meat, thawing time can be selected for 4 hrs, 6 hrs, 10 hrs, and 12 hrs sequentially. • When “Thaw” ends, CoolSelect Zone™ display returns to “Zero Zone” condition. • When “Thaw “ ends, there are no juice in the meats and they are half-freezed condition so it is easy to cut them for cooking. • To cancel this option, press any button except “Thaw”. • The approximate thawing time of meat and fi sh are shown below. (Based on 1inch thickness) THAW TIME WEIGHT 4 hours 363g (0.8Ib) 6 hours 590g (1.3Ib) 10 hours 771g (1.7Ib) 12 hours 1000g (2.2Ib) Depending on the size and thickness of meat and fi sh, the thawing time may vary. The above weight represents the total weight of food in the CoolSelect Zone™ Drawer. Ex) The total thawing time for 400g frozen beef and 600g frozen chicken will be 10 hours. With the “Thaw” option, food which is not needed to thaw in the CoolSelect Zone™ Drawer should be removed. • Do not put your fi ngers, hands or any other unsuitable objects in the chute or ice-maker bucket. - It may result in personal injury or material damage. • Never put fi nger or any other objects in the dispenser opening. - It may cause injury. • Use only the ice maker provided with the refrigerator. • The water supply to this refrigerator must only be installed/connected by a suitably qualifi ed person and connect to a potable water supply only. • In order to operate the ice maker properly, water pressure of 138 ~ 862 Kpa is required. • If you have a long vacation or business trip and won’t use water or ice dispensers, close the water valve. - Otherwise, water leakage may occur. • Wipe excess moisture from the inside and leave the doors open. - Otherwise, odor and mold may develop. To get more space,you can remove top freezer drawer since it does not affect thermal and mechanical characteristics. A declared storage volume of frozen food storage compartment is calculated with this drawer removed. CAUTION WARNING WARNING % JOEC% JOEC1.1.
18_ operating REMOVING THE FREEZER ACCESSORIES Cleaning and rearranging the interior of the freezer is simple. 1. Remove the Glass shelf by pulling the shelf out as far as it will go. Then, gently lift it up and remove it. 2. Remove the door bin by holding the door bin with both hands and then gently lift it up. 3. Remove the Plastic drawer by pulling it out and slightly lifting it up. 4. Remove the Icemaker bucket by lifting up and pulling it out. Do not use excessive force when removing the cover. Otherwise, the cover may break and cause injury. Soft Freeze • When “Soft Freeze” is chosen, the temperature on the digtal panel displays -5ºC regardless of the set temperature of the refrigerator. • “Soft-Freeze” temperature helps keep meats and fi shes fresh longer. • Can cut meat easily without drips. Zero Zone (0ºC) • When “Zero Zone” is chosen, the temperature of the CoolSelect Zone™ Drawer is kept at 0 ºC regardless of the set refrigerator temperature. • “Zero Zone” temperature helps keep meat or fi sh fresh longer. Cool • When “Cool” is chosen, the temperature will be the same as the set temperature of the refrigerator. The digital panel shows the same temperature as that of the display panel. • The CoolSelect Zone™ Drawer allows extra refrigerator space. Depending on the beverages, the cool-down time may vary. For “Quick Cool” option, food stored in the CoolSelect Zone™ Drawer should be removed. WARNING % JOEC% JOEC1.1.
operating _19 02 OPERATING Before removing any accessories, make sure that no food is in the way. When possible, remove the food altogether to reduce the risk of accidents. To get the best energy effi ciency of this product, please leave all selves, drawers and baskets on their original position like as illustration in page (17). CLEANING THE REFRIGERATOR Do not use Benzene, Thinner or Clorox™ for cleaning. They may damage the surface of the appliance and can create a risk of fi re. Do not spray the refrigerator with water while it is plugged in, as it may cause an electric shock. Do not clean the refrigerator with benzene, thinner or car detergent for risk of fi r e . REPLACING THE INTERIOR LIGHT For LED lamp, please contact service engineer to replace it. REMOVING THE FRIDGE ACCESSORIES 1. Remove the spill Proof Glass Shelf by pulling the shelf out as far as it will go. Then, gently lift it up and gently remove it. 2. Remove the Vegetable & Fruit Drawer by pressing on the indentations found on the inside left and right sides of the Veggie Box/ Dry Box cover and remove by pulling forward. Holding the drawer with one hand, lift it up a little bit while pulling it forward and take it out of the refrigerator. 3. Remove the Gallon Door Bin by holding the bin with both hands and gently lifting it up. 4. The Z Shelf is attached to the cabinet wall. Remove the wine shelf by sliding it up and gently lifting the shelf out of the tabs. Ensure that the Z Shelf is fi tted as shown in the diagram and not upside down. CAUTION WARNING CAUTION % JOEC% JOEC1.1.
20_ operating 6. Once you have completed this process, hold the Ice Type button for 3 seconds to reset the fi lter schedule. 7. Lastly, Dispense 1L of water through water dispenser and throw away. Make sure that water fl ows clearly again before drinking. A newly installed water fi lter cartridge may cause water to briefl y spurt from the water dispenser. This is due to air getting into the line. It should pose no problem to operation. Ordering replacement fi lters To order more water fi lter cartridges, contact your authorised Samsung dealer. USING THE DOORS The refrigerator doors are equipped with a door opening and closing feature that ensures that the doors close all the way and are securely sealed. After opening beyond a certain point, the door will “catch” and remain open. When the door is ajar ahead of the catch that allows it to stay open, it will close automatically. CHANGING THE WATER FILTER To reduce risk of water damage to your property DO NOT use generic brands of water fi lers in your SAMSUNG Refrigerator. USE ONLY SAMSUNG BRAND WATER FILTERS. SAMSUNG will not be legally responsible for any damage, including, but not limited to property damage caused by water leakage from use of a generic water fi lter. SAMSUNG Refrigerators are designed to work ONLY WITH SAMSUNG Water Filter. The “Filter Indicator” light lets you know when it is time to change your water fi lter cartridge. When the fi lter indicator light changes to red, it is time to change the fi lter. To give you some time to get a new fi lter, the light will come on up just before the capacity of the current fi lter runs out. Changing the fi lter on time provides you with the freshest, cleanest water from your fridge. 1. Remove the water fi lter from the box and put a month indicator sticker on the fi lter as shown. 2. Place a sticker on the fi lter that dates six months in the future. For example, if you are replacing the water fi lter in March, put the “SEP” (September) sticker on the fi lter to remind you to replace in September. Normally fi lter life is about every 6 months. 3. Next, remove the fi xed cap by turning it counter clockwise. 4. Remove the new fi lter’s protective cap and remove the old fi lter. 5. Position and insert the new fi lter into the fi lter housing. Slowly turn the water fi lter clockwise 90º to align with the indication mark on the cover, locking the fi lter in position. Make sure that the indicator is lined up with the “lock” position. Do not over tighten. 1 2 34 5 Align the Align the indication indication mark mark with lock with lock positionposition Cover fi lterCover fi lter StickerSticker(month (month indicator)indicator) WARNING % JOEC% JOEC1.1.