Samsung Rs 21 Hdlmr Owners Manual

							21
INSTALLATION INSTRUCTIONS
REMOVING THE REFRIGERATOR DOORS
1) With the door closed, remove the upper hinge cover (➀) using a screwdriver, and then discon-nect  
the wires (➁).
2) Remove hinge screws (➂) and ground screw (➃) counter-clockwise, and take off the upper  hinge (➄) in the    
direction of the arrow (➅). Take care when removing the door to ensure that it does not fall on you.
3) Remove the door from the lower hinge (	) by
lifting the door (
➇).4) Remove the lower hinge (➈) from the bracket
lower hinge (➉) by lifting the lower hinge (➈)
in the direction of the arrow.
Removing the Refrigerator Door
NOTE
• After disassembling the freezer / refrigerator door, move it to the appropriate location. you must reassemble it.
DA99-00494B  4/7/03 2:29 PM  Page 21
 
						

							22
REATTACHING THE REFRIGERATOR DOORS
Reattaching the Freezer Door
1) Insert the lower hinge (➀) in the bracket
lower hinge (➁).2) Reattach the freezer door by inserting the
hose (➂) in the lower side of the door into
the hole in the lower hinge (➃) and pulling
the hose down.  
3) Insert the upper hinge shaft (➄) into the hole (➅). After levelling  the upper hinge hole
(➆) with the hole of the cabinet (
➇). Fasten bolts (➈) and screw (➉) in a clockwise direction.
4) Connect the wires.  5) Put the front part of the upper hinge cover (    )
on the front part of the upper hinge (    ) and
reattach from the front part of the upper hinge
cover first.11
12
DA99-00494B  4/7/03 2:29 PM  Page 22
 
						

							23
INSTALLATION INSTRUCTIONS
REATTACHING THE REFRIGERATOR DOORS
Reattaching the Refrigerator Door
1) Insert the lower hinge (➀) in the bracket
lower hinge (➁).2) Place the hole in the refrigerator door (➂)
over the lower hinge (➃).
3) Insert the upper hinge shaft (➄) into the hole (➅). After levelling  the upper hinge hole (➆)
with the hole of the cabinet (
➇). Fasten  hinge screws (➈) and screw (➉) in the clockwise direc-tion.
4) Connect the wires.  5) Put the front part of the upper hinge cover (    )
on the front part of the upper hinge (    ) and
reattach it from the front part of the upper
hinge cover first.
11
12
DA99-00494B  4/7/03 2:29 PM  Page 23
 
						

							24
REATTACHING THE REFRIGERATOR DOORS
FRONT LEG COVER
SCREW
1) While pressing the front face of coupler (➁), insert the water line (➀) in the coupler.
2) Tighten the screw on the clamp (   ).  a
Put on the front leg cover by turning the three screws clockwise, as shown in the figure.
Reattaching the Water Tube (Optional)
Reattaching the Front Leg Cover (Optional)
DA99-00494B  4/7/03 2:29 PM  Page 24
 
						

							25
INSTALLATION INSTRUCTIONS
ADJUSTING THE CLEARANCE BETWEEN THE DOORS
The doors will be uneven if the refrigerator is not level.
Case 1) Freezer door is lower than
that of the refrigeratorInsert a straight screwdriver (-) () into a
slot of the control lever (➁), turn it clockwise
and level the refrigerator.
Case 2) Freezer door is higher than
that of the refrigeratorInsert a straight screwdriver (-) () into a
slot of the control lever (➁), turn it clockwise 
and level the refrigerator.
Do not make small adjustment by turning the control lever, Please refer to the next page.
DIFFERANCE  OF HEIGHT
DIFFERANCE  OF HEIGHT
➀DRIVER(-)
➀DRIVER(-)
➁CONTROL LEVER
➁CONTROL LEVER
Please level the refrigerator first.
NOTE
DA99-00494B  4/7/03 2:29 PM  Page 25
 
						

							26
ADJUST THE CLEARANCE BETWEEN THE DOORS
Making small adjustments between doors.
If the door of the freezer is lower than that of
the refrigerator.If the door of freezer is higher than that of the
refrigerator.
3) After adjusting the doors, turn the nut () turn clockwise(                ) until the lower end of the bolt, then tighten
the bolt again with the wrench (➂) to fix the nut().
If you do not fix the nut () firmly, the bolt (➁) may be released.
2) Please adjust the height difference between the doors turning the bolt (➁) turn clockwise(                   ) or
counter  clockwise (              ).
When you turn clockwise (               ), the door goes up.
➂WRENCH Adjustment part
Adjustment part
➀NUT
➁BOLT➂WRENCH
➀NUT
➂WRENCH
➀NUT➂WRENCH
➀NUT➁BOLT
➂WRENCH
➁BOLT ➂WRENCH
➁BOLT
➁BOLT ➁BOLT
Please open the doors and adjust the doors as follows:
1) Release the nut (
) on the lower hinge until the upper end of the bolt (➁).
When you release the nut(), use enclosed hex wrench (➂) to turn the bolt(➁) a little counter clockwise
to make the nut(
) loose with your fingers.NOTA
NOTE
NOTA
DA99-00494B  4/7/03 2:29 PM  Page 26
 
						

							27
INSTALLATION INSTRUCTIONS
CHECKING THE WATER DISPENSER LINE (OPTIONAL)
Checking the Parts
NOTE
A universal water supply kit is available at extra cost from your dealer. The refrigerator manufacturer
recommends using a water supply kit containing copper tubing. 1) In order to operate the ice maker properly, water pressure of 1.4 ~ 10 kgf/cm
2 is required.
In this range a 100 cc paper cup can be filled in 10 seconds.
2) The water filter removes particles. It does not sterilize or destroy any micro-organisms.
3) If the refrigerator is installed in an area with low water pressure (below 1.4kgf/cm
2), you should install
a booster pump to compensate for the low pressure.
4) Ensure the water storage tank inside the refrigerator is preperly filled initially. Push the water dis
penser lever until the water runs from the outlet.
Purifier
Sealing tape
Clip A x 8EA
Purifier lock  
station
Tightening band Water line
Purifier Tapping screw x 12EA
(Interior model)
(Exterior model)
DA99-00494B  4/7/03 2:29 PM  Page 27
 
						

							28
INSTALLING OF THE WATER DISPENSER LINE
WARRANTY INFORMATION
This water line installation is not covered by the refriger-ator
or ice maker manufacturers warranty.
Follow these instructions carefully to minimise the risk of
expensive water damage.
Note:
If the coupler does not fit on the current tap, go
the nearest authorised service dealer and purchase
the right couplers fittings.
Connecting to water supply line
- Shut off the main water supply line and turn the Ice 
maker to the off position.
- Locate the nearest cold drinking water line.
- Follow the instructions in the ice maker installation kit.
- Slip the compression nut and plastic ferrule
through the plastic tube.
- After inserting the sleeve, tighten the compres-sion
nut onto 1/4” compression fitting(union).
Connect the water line to the refrigerator
Check the water supply line
Waterline must be connected to drinkable water onlyNOTEDo not overtighten the compression nut.
NOTE
- Slip the compression ferrule and nut on copper(or plastic) tubing as 
shown.
Tighten the comperssion nut onto the com-pression fitting(union).
- Turn water on and check for any leakege.
Connect the water pipe with coupler and tap.
- Close the main water tap.
- Connect coupler “A” to the tap.
- Every join should be protected with sealing tape.Compression
Nut
Sleeve
Compression
fitting
Ferrule
Ferrule
Compressi
on Nut
For Interior Model
(Case 1)
(Case 2)
COUPLER “A”
TAP
CAUTION
The water line must be connect-ed
to the cold water pipe.
If it is connected to the hot water
pipe, it may cause the
purifier to malfunction.
1. Cold Water line
2. Pipe Clamp.
3.Copper (or Plastic) line
4.Compression Nut
5.Compression Sleeve
6.Shut Off Valve
7.Packing Nut.
DA99-00494B  4/7/03 2:29 PM  Page 28
 
						

							29
INSTALLATION INSTRUCTIONS
INSTALLING THE WATER DISPENSER LINE
- Remove the compressor cover of the refrigerator.
- Connect the water line to the valve, as shown in the figure.
- When connected, check if there is any leakage.
If any, repeat the connection.
- Reattach the compressor cover of the refrigerator.
- Using clip ”A”, fix the water line to the wall (the back of refrigerator).
- When the water line is secure, make sure whether the
water line is not excessively bent, pinched or squashed.
Complete the installation of the water supply line.
- Power on the refrigerator and press the lever on the right of the
dispenser until water runs out through the water line and all air has been empty.
- At this time, check for any possible leakages at the join point in the water line.
After securing the water line, move the refrigerator to the required location.
Once the refrigerator is in position, do not move possibly.
- As shown, separate the fixed cap in the refrigerator by rotating
it counterclockwise.
Remove the water filter from the box and put a month indicator
sticker on the filter as shown.
- Write the month you installed the filter on the label.
EX) If the water filter was installed in March, put “MAR”
- Remove the protective cap then position and insert the filter as shown,
- Slowly turn the water filter clockwise 90º to align the indication mark on the
cover, locking the filter in postion. Do not overtighten.
Please check if the indication line aligns with the lock position.
CLIP A
WATER LINE
STICKER
(MONTH INDICATION)SEPARATION
OF RED CAP
ALIGN THE INDICATION MARK
WITH LOCK POSITION.COVER FILTER WATER LINE
CONNECTION NUT
Connect the water line to the refrigerator.
Secure the water line.
Install the water filter.
CAUTION
COMPRESSOR COVER OF
REFRIGERATOR
DA99-00494B  4/7/03 2:29 PM  Page 29
 
						

							30
INSTALLING THE WATER DISPENSER LINE
Remove any residual matter inside the purifier. (Model with the purifier)
- Open the main water tap to check whether water
is running through the water tube on the water
inlet side of the purifier.
- If water does not come out through the line,
check whether the tap is open.
- Leave the tap open until clean water is running
out and any residual matter that built up during
manufacturing has been removed. - If you wish to reassemble the water inlet
and outlet sides of the purifier during purifier
installation, see the reference illustration. Select the location where the purifier is to install. (Model with the purifier)
- Cut the water line attached to the purifier
to the appropriate place after measuring
the distance between the purifier and the
cold water tap.
COUPLER
SIDE OF PURIFIER
WATER LINE
PURIFIERWATER
OUTLET SIDE
OF PURIFIER
WATER INLET
SIDE OF PURIFIER
Line outlet
90 degreePURIFIER
WATER
REFERENCE
WARRANTY INFORMATION
This water line installation is not covered by the refriger-ator
or ice maker manufacturers warranty.
Follow these instructions carefully to minimise the risk of
expensive water damage.
Note:
If the coupler does not fit on the current tap, go
the nearest authorised service dealer and purchase
the right couplers fittings.
Connect to the water supply line
Connect the water pipe with coupler and tap.
- Close the main water tap.
- Connect coupler “A” to the tap.
- Every join should be protected with sealing tape.
COUPLER “A”
TAP
CAUTION
The water line must be connected
to the cold water pipe.
If it is connected to the hot
water pipe, it may cause the
purifier to malfunction.
For Exterior model
DA99-00494B  4/7/03 2:29 PM  Page 30