Samsung Rl 44 Ecrs Owners Instructions

							11
STORING FOOD IN THE REFRIGERATOR OR FREEZER
MAKING ICE
Pour water into the ice cube maker.
•   Fill the ice maker up to about 80% with water.
Place the ice cube maker in the top 
freezer drawer.
To take out the ice cubes:
•   Twist the ice cube maker slightly.
Making ice quickly
To make a large quantity of ice quickly, press the “Super Freeze” button to select the 
fast freeze function. Danger of explosion
• 
  The coldest parts of the refrigerator is the rear panel. This is the best place to store 
delicate foodstuffs.
•    Glass bottles containing liquids that can freeze should never be stored in the freezer 
as the glass can explode when the contents freeze.
Warning
Note
Top freezer drawer
•   Store packed frozen foods, like ice cream, bacon and pizza.
•   
Place the ice tray in this drawer in order to achieve optimal ice freezing.
Middle/lower freezer drawer
•    Store fresh meat and fish or dried foods, which are divided into suitably sized portions.
•   
Do not store food which goes bad easily at low temerature, such as bananas, melons.
•   
Do not put any newly introduced food for freezing near to frozen food.
•   
Do not place carbonated or fizzy drinks in the freezer compartment.
B. Freezer
Note
•  
Your appliance is frost free, which means there is no need to manually defrost your 
appliance, as this will be carried out automatically.
•    Temperature rising during the defrost can comply with ISO requirement, But if you 
want to prevent on undue rise in the temperature of the frozen food while defrosting 
the appliance. Please wrap the frozen food in several layers of newspaper.
•    The appliance may not operate consistently (possibility of defrosting the contents 
or the temperature becoming too warm in the frozen food compartment) when sited 
for an extended period of time below the cold end of the range of temperatures for 
which the refrigerating appliance is designed.
•    To get more space, you can remove drawers as 
following picture. It does not affect thermal and 
mechanical characteristics. A declared storage volume 
of frozen food storage compartment is calculated with 
these drawers removed.
•    To get the best energy efficiency of this product, 
please leave all selves, drawers and baskets on their 
original position like as illustration in page (19.)
•    For freezing test, remove 
1 drawer.
1
DA99-01220J.indb   112010.6.23   10:44:28 AM 
						

							12
USING THE WATER DISPENSER (Only available on some models)
With the water dispenser, you can obtain chilled water easily without opening the refrigerator door. In 
addition, you can save electricity by more than 30% reducing the number of times the door is open.
Push lever
Water tank
WHEN  THE WATER  DISPENSER  IS NOT  USED,  THE FOLLOWINGS  ARE RECOMMENDED
Fix the water supply device tightly into the fixing hole.
•   The door will not be closed automatically when the water 
supply device is pulled out for a long time because of cold 
leaking.
Place a separate spare beverage bottle in the location 
of the exclusive water tank.
• Two 1.5 litre bottles can be placed.
Water tank cap
Water supply device
FILLING THE WATER TANK
Open the round cap and fill the water tank up with 
drinking water.
•    Don't fill up the water tank too much(just over 4.2 litres).       
It can cause overflow when the door is opening and closing.
Close the round cap by pushing down on it until it 
clicks into proper place.
Push the water dispenser lever with a cup.Push
DA99-01220J.indb   122010.6.23   10:44:29 AM 
						

							USING THE WATER DISPENSER (Only available on some models)
13
INSTALLING A REGULAR BOTTLE
Press the fixing lever, lift the exclusive water tank 
upwards, then remove it.
Remove the water supply device from the 
exclusive water tank, then set the inner groove 
of the water supply device in a regular mineral 
water bottle and fix‑it in position by turning it.
Turn the water supply device over, then fix‑it in 
position in the fixing hole.
•  
Gurgling sounds may be heard when air enters the water bottle from regular mineral 
water or beverage bottles.
•   
Some regular mineral water or beverage bottles may not fit the water supply device, 
depending on their size.
•   
If water does not come out satisfactorily when you press the “push” lever, press it again.
•   
Do not use carbonated drinks, such as coke, cider or sodas. When you press the button, 
the beverage may spurt out due to the pressure of carbonic gas accumulated in the upper 
part of beverage bottle.
• For better hygiene, beverages with a high sugar content (juice, soft drinks) are not   
  recommended.
• You can use bottled mineral water or boiled tap water unless it does contain any particles.
Note
CLEANING THE WATER DISPENSER
Connection path
Wipe out the connection path and surrounding area with a clean damp cloth.
Dispenser Tray
Pull out the tray with fingers.
Empty the water in the dispenser tray, then clean it using warm water and detergent.
WHEN  THE WATER  DISPENSER  IS NOT  USED,  THE FOLLOWINGS  ARE RECOMMENDED
FILLING THE WATER TANK
DA99-01220J.indb   132010.6.23   10:44:29 AM 
						

							14
CLEANING THE WATER DISPENSER
Water Tank / Supply Device
Pull upward and disassemble the hooks on both 
sides of the large‑sized cap.
Loosen the water supply device by turning it in 
the direction of the arrow and removing it.
•  
Clean the water tank frequently if it used to dispense tea or other such beverages. 
Only use filtered tea. For better hygiene, beverages with a high sugar content (juice, 
soft drinks) are not recommended.
•   
Deposits can be cleaned by wiping the tank with a cloth dampened in vinegar or salt water.•   Check that the rubber seal on the water supply device has not slipped off or is not 
damaged by-a sharp-edged object. Otherwise, it may leak.
Caution
Wipe the large‑sized cap and the exclusive 
water tank with warm water and detergent.
•   Hold the cap and pull it upwards to remove it. 
Clean the cap.
After cleaning the water supply device with a soft 
brush, press the water supply device operation 
lever, then wash it in running water.
REPLACING THE INTERIOR LIGHT
Please contact service engineer to replace it. Note
Press the locking device on the rear left 
and right side of the drawer cover and 
pull the drawer cover to remove it.   
(Only available on some models)
REMOVING THE INTERIOR PARTS
Drawers
DA99-01220J.indb   142010.6.23   10:44:30 AM 
						

							15
REVERSING THE DOOR SWING
•  
Before reversing the door, ensure first that the refrigerator is disconnect by the plug 
from the mains. You should take out contents and accessories like door guard from 
the doors.  Be careful not to drop the doors during disassembling or assembling.
Warning
‑ Read these instructions completely and carefully
1. Handle parts carefully to avoid scratching the paint.
2. Lay out all the screws by their related parts to avoid using them in the wrong places.
3. Provide a non-scratching work surface for the doors. (ex:blanket)
4. During door reversing, refrigerator should not be stained with oil.
5.    We recommend to use tools descrided below. (Possible to use simliar size of socket 
wrench & wrench)
1.   Disassemble the CAP CABI 
after removing 2 screws.
These operating instructions cover various models. 
The characteristics of your appliance may differ slightly from those described in this instructions.
‑ 
DISASSEMBLY OF THE FRIDGE DOOR
2.   
Disconnect electric wires 
inside of the CAP CABI.3.   Remove 3 bolts on the top 
of the refrigerator with 10mm 
socket wrench. Make sure the 
door is firmly closed.
4.   Disassemble the Fridge door 
by lifting it upward. 
       Be careful not to drop and 
scratch the face of the 
Fridge door.5.  
Disassemble the COVER 
WIRE DOOR on the top of 
the fridge door with a flat-
head screw driver by putting it 
into the indicated position
(∆).
6.   Disjoin the COVER WIRE 
HINGE R from the ASSY 
HINGE UPP as shown. Take 
out the electric wire from the 
COVER WIRE HINGE R.
ASSY HINGE UPP
COVER WIRE HINGE R
COVER WIRE DOOR
Not providedAdditional part
Phillips Head 
Driver (+) Flat Head  
Driver (-) 10mm  
Socket Wrench   
(for bolts) 11mm  
Wrench
(for hinge shaft) Allen Wrench
(3/16inch)
(for Mid hinge) Cover Wire 
Hinge L
(In Top Cover)
CAP CABI
DA99-01220J.indb   152010.6.23   10:44:32 AM 
						

							16
‑  
DISASSEMBLY OF THE 
FREEZER DOOR
REVERSING THE DOOR SWING
SHAFT
GROMMET HINGE
8.   
With 11mm wrench, 
separate the HINGE SHAFT 
and then flip the HINGE and 
reattach the HINGE SHAFT.    9-1. 
  After rejoining the COVER 
WIRE HINGE L and 
the ASSY HINGE UPP, 
Switch the position of the    
GROMMET HINGE and the 
CAP SPACE DOOR.             
9-2.   
When disassembling CAP 
SPACE, do not  Push 
both  side hooks but 
bottom hook as shown.
10.    Switch the position of the 
STOPPER DOOR and 
the GROMMET HINGE as 
shown. 
11.  
Remove 2 bolts and screw 
to disassemble the ASSY 
HINGE MID. 
14.    Disassemble the ASSY 
HINGE LOW as shown and 
put the AUTO GUIDE upside 
down, switch the position of 
the SHAFT.12.   Disassemble the Freezer 
door by lifting it upward.
Be careful not to drop and 
scratch the Freezer door. 13. 
  Disassemble the COVER 
LEG FRONT by removing 
the 2 screws.
ASSY HINGE LOW
AUTO GUIDE
COVER LEG FRONT 
When joining, tighten 
a screw not to make 
unpredicted noise.
STOPPER
GROMMET
7.  
Switch the direction of the 
electric wire as below. Take 
out the COVER WIRE HINGE 
L from the underneath the 
CAP CABI and rejoin it with 
the electric wire.
Note
DA99-01220J.indb   162010.6.23   10:44:36 AM 
						

							17
REVERSING THE DOOR SWING
‑ ASSEMBLY OF THE FREEZER DOOR
‑ REVERSING THE HANDLE BAR [FRIDGE/FREEZER]
15.   
Detach the CAP SCREW 
HANDLE with flat screwdriver and 
disassemble the HANDLE BARs.16.   Switch the position of the 
CAP HOLE DOORs, pulling 
out and pushing them in. 17. 
  Reattach the HANDLE 
BARs on the other side of 
doors in reverse order.
18.  
Exchange the positions of a bolt and 
the assy HINGE LOW after making 
a hole with phillips head driver on 
the left bottom side of the unit.19.    After switching the position 
of the CAP HOLE HINGE 
LOW, reassemble the 
COVER LEG FRONT.  20. 
  Switch the position of the 
CAP HOLE HINGE MID 
and a screw.
21.  
Switch the position of the 
STOPPER DOOR and the 
GROMMET HINGE as shown.22.    Switch the position of the 
GROMMET HINGE and 
the CAP HINGE HOLE.23.   Carefully put the Freezer door 
back on and assemble HINGE 
MID with 2 bolts and a screw.
24. Carefully put the Fridge door back on. 25. 
 
Secure the ASSY HINGE UPP with 3 bolts as 
shown. Make sure the Fridge Door is firmly closed.
‑ 
ASSEMBLY OF THE FRIDGE DOOR
STOPPER
GROMMET
DA99-01220J.indb   172010.6.23   10:44:38 AM 
						

							18
REVERSING THE DOOR SWING
• Check that the power plug is correctly connected.
• Is the temperature control on the front panel correctly set?
• Does sun shine on the appliance or are there heat sources nearby?
• Is the back of the appliance too near to the wall?
The appliance is not operating at all or the temperature is too high
•   
Is the temperature control on the front panel set to the coldest temperature?
• Is the surrounding temperature too low?
• Did you put the hot food in the refrigerator?
The food in the refrigerator is frozen
• Check that the appliance is installed on a stable, level floor.
• Is the back of the appliance too near to the wall?
• Have any foreign objects fallen behind or under the appliance?
• Is there noise coming from the compressor in the appliance?
•    A ticking sound may be heard inside the appliance; this is normal. This sound occurs when the 
various accessories contract or expand.
•   
Heat-proof pipes are installed in the front corners of the appliance to prevent condensation from forming. 
When the surrounding temperature rises, this may not always be effective. However, this is not abnormal.
•   In very humid weather, condensation may form on the outer surface of the appliance when the 
moisture in the air comes into contact with the cool surface of the appliance.
The front corners and sides of the appliance are warm and condensation starts to form
PROBLEMS AND SOLUTIONS
There are unusual noises
29.   Detach the Fridge and Freezer gaskets and attach them 
after rotating 180˚. (Make sure the door gaskets are 
properly arranged. If not, there can be a noise or dew 
can be formed which affects perfomance of the unit.) 
26.    Switch the position of the 
CAP HOLE HINGE UPP.
30.   Make sure the doors are working 
properly.27.  Reconnect the electric wires and 
reposition the wires inside of the 
CAP CABI as shown below.28.    Reassemble the CAP 
CABI after assuring the 
position of Wires.
CAP HOLE HINGE
DA99-01220J.indb   182010.6.23   10:44:39 AM 
						

							19
VIEW OF YOUR FRIDGE / FREEZER
PROBLEMS AND SOLUTIONS
Power Saving Tips
•   
Install the appliance in a cool, dry room with adequate ventilation.   
Ensure that it is not exposed to direct sunlight and never put it near a direct source of heat (radiator, for example).• Never block any vents or grilles on the appliance.
• Allow warm food to cool down before placing it in the appliance.
•   Put frozen food in the refrigerator to thaw. 
You can then use the low temperatures of the frozen products to cool food in the refrigerator.
•    Do not keep the door of the appliance open for too long when putting food in or taking food out. 
The shorter time for which the door is open, the less ice will form in the freezer.
Tips
• This is the refrigerant, which cools the inside of the appliance.
You can hear a liquid babbling in the appliance
• You did not seal the food.
• Check food are covered and ensure the cold inlet is clean.
There is a bad smell inside the appliance
• Is the air outlet on the appliance plugged up?
• Space the food out as much as possible to improve ventilation.
• Is the door fully closed?
There is a layer of frost on the appliance’s walls
•   
Can occur if food with a high water content is stored uncovered with a high humidity level or 
the door has been left open for a-long time.
• Store the food with a cover or in sealed containers.
If condensation forms on the inside wall of the appliance and around vegetables
WATER DISPENSER (Only available on some models)
REFRIGERATOR LIGHT (LED Lamp or 
incandescent, depending on the model)
FRIDGE
REFRIGERATOR SHELVES (tempered glass, depending  on the model)
FRESH SAFE DRAWER
(ONLY  AVAILABLE  ON SOME  MODELS)
FRESH SAFE DRAWER /
CHILLED ROOM /
COOLSELECT  ZONE 
(ONLY AVAILABLE  ON SOME  MODELS)
FREEZER
TOP FREEZER DRAWER
FREEZER DRAWER
DAIRY GUARD (Only available on some models)
MULTI-PURPOSE GUARD(Only available on some models)
DA99-01220J.indb   192010.6.23   10:44:40 AM 
						

							Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. Samsung Electronics America, Inc.105 Challenger Road
Ridgefield Park, NJ 07660-0511 1-800-SAMSUNG (7267864) www.samsung.com
In an effort to promote recycling this user manual is printed on recycled paper.
Ambient Room Temperature Limits
This refrigerator is designed to operate in ambient temperatures specified by its  
temperature class marked on the rating plate.
Class SymbolAmbient Temperature range (°C)
Extended Temperate SN+10 to +32
Temperate N+16 to +32
Subtropical ST+16 to +38
Tropical T+16 to +43
  
Internal  temperatures  may  be  affected  by  such  factors  as  the  location  of  the  refrigera-
tor,  ambient  temperature  and  the  frequency  with  which  you  open  the  door.  Adjust  the  
temperature as required to compensate for these factors.
Correct Disposal of This Product 
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate col-
lection systems)
This marking on the product, accessories or literature indicates that the product and 
its electronic accessories (e.g. charger, headset, USB cable) should not be disposed 
of with other household waste at the end of their working life. To prevent possible 
harm to the environment or human health from uncontrolled waste disposal, please 
separate these items from other types of waste and recycle them responsibly to 
promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this 
product, or their local government office, for details of where and how they can take 
these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and con\
ditions 
of the purchase contract. This product and its electronic accessories should not be 
mixed with other commercial wastes for disposal.
English
DA99-01220J.indb   202010.6.23   10:44:40 AM