Samsung Projector Sp P410m User Manual

							Using3-3
3-3 Remote Control 
1. POWER Button () 
Use this button for turning the product on and off. 
2. SOURCE Button 
Used to check or select the connection status of external 
devices.
3. MENU Button  ()
Used to display Menu Screen.
4. Move ( )/ ( ) Button  
Used to move to or select each menu item.
5. V. KEYSTONE Button  ()
Use this when the screen is displayed in a trapezoid shape. 
6. REWIND button ()
Rewind the movie in the Media.P mode. 
7. PAGE DN button ()
Use to select the previous file. 
8. ZOOM Button 
Enlarges picture.
9. STILL Button ()
Used to see still images. 
10. MUTE Button ()
Press to mute the sound temporarily. Press the MUTE button 
again or the VOL button ( ) when the sound is muted to 
hear sound again.
11. RETURN Button ()
Returns to the previous menu.
12. MEDIA.P Button
Used as a shortcut button to MEDIA.P.
13. VOL Button ()
Used to control the volume.
14. FAST FORWARD button ()
Fast forward the movie in the Media.P mode.
15. PAGE UP Button ()
Use to select the next file. 
16. SUBTITLE Button 
Sets subtitles.
17. STOP Button ()
Stops video or music in the MEDIA.P mode.
 Make sure to place your remote control on a table or desk. 
If you step on the remote control, you may fall and hurt 
yourself or the product may be damaged. 
  You can use the remote control up to a distance of about 23 
feet(7 m) from the product.
  
						

							3-4Using
3-4 LED Indications 
LED Indications 
:Light is On  :Light is Blinking  :Light is Off
Clearing Indicator Problems 
 This Projector uses a cooling fan system to keep the unit from overheating. Operation of the cooling fan may cause noise, 
which does not affect the product performance and is part of normal operation. 
 
3-5 Using the Screen Adjustment Menu (OSD: On Screen Display) 
The Screen Adjustment Menu (OSD: On Screen Display) Structure
STAND BYTEMPINFORMATION
This state occurs when power is supplied to the projector normally after the POWER button 
on the projector or the remote control has been pressed.
• This state appears when the projector is preparing an operation after the POWER button 
on the projector or the remote control has been pressed. 
• The POWER button is pressed to turn off the projector, and the cooling system is in 
operation to cool off the inside of the projector.
• This is the state where the product is turned off automatically since there was no signal 
input while a PC cable was connected. 
The projector is in normal operating condition. 
Refer to Action 1 below if the cooling fan inside the projector is not in normal operation con-
dition.
Power is turned off automatically when temperature inside of the projector goes beyond 
the control limit. Refer to Action 2.
This state occurs when the auto color compensation function has an error. Refer to Action 
3. 
CLASSIFICA
TIONSTATEMEASURES
Action 1  When the cooling fan system is 
not in normal operating condi-
tion.If the symptom remains even after disconnecting and then reconnecting 
the power cord and turning the projector on again, contact a Samsung ser-
vice center. 
Action 2  When temperature inside of the 
projector becomes too high.Adjust the installation state of your projector by referring to the Installation 
Precautions section listed above. Cool down your projector sufficiently and 
then operate it again. If the same problem occurs continually, contact a 
Samsung service center. 
Action 3  When the sensor system inside 
the projector is not operating 
normally. Cool your projector down sufficiently and then operate it again. If the same 
problem occurs again, contact a Samsung service center.  
						

							Using3-5
 3-5-1. Input
 3-5-2. Picture
MENUSUB-MENU
 InputSource List  Edit Name
 PictureMode Size Position Digital NR Black Level
Film Mode  PC Zoom
 SetupInstall V-Keystone Background Test Pattern Factory Default
Video Type
 OptionLanguage Menu Option Information
MENUDESCRIPTION
Source List  You can select a device connected to the projector to display.
• - -
Edit Name You can edit the names of devices connected to the projector.
• - - - - - - - 
- - -  
						

							3-5Using
MENUDESCRIPTION
Mode Select a screen state which is customized to your projector or change the screen mode as required.
• 
•  : Select this mode for a brighter and sharper picture than Standard Mode.
•  : This is the picture mode optimized to the standard broadcast signal. 
•  : Optimize the picture for watching movies. 
•  : Optimize the picture for presentatations. 
 You can only set in [PC] mode.
 
•  : Optimize the picture for watching sports. 
•  : Select when you adjust the picture to suit your preference.
•  : Used to adjust the contrast between the object and the background. 
•  : Used to adjust brightness of the entire picture.
•  : Used to adjust the sharpness of the picture. 
•  : Used to adjust color lighter or darker.
 You can only set the  in  mode. 
•  : Used to obtain more natural color of objects using Green or Red enhancement.
 When the input signal is  or PAL and SECAM of the  mode, the  cant be 
adjusted.
 
•  : You can change tint of the entire screen to suit your needs.
 You can not set in  mode. 
•  : Suitable to use when the surroundings are very bright. 
•  : Suitable to use when the surroundings are somewhat bright. 
•  : Used when watching most scenes. This presents colors most accurately. 
•  : Select this when watching a black and white movie for optimal quality.
•  
•  : Displays the native color gamut. 
•  : Normal Color Gamut offers flat and natural color tone.
•  : Standardized for Video Equipment by the Society of Motion Picture and 
Television Engineers.
•  : Regulations and standards for European Broadcasting Production and technology, 
standardized by the European Broadcasting Union.
•  : An image compensation function that controls the settings according to the video 
properties. 
• : The best setting for watching a film. 
•  : The best setting for watching a TV program.
• : The best setting when you have a PC connected. 
•  : The gamma mode suitable for watching a movie. 
•  : Used to save custom picture settings. 
•  : Restores the mode settings to the factory defaults. 
Size You can select a screen size according to the type of scene. 
• ---
 Available picture size in the PC and Media Play mode is , .  
						

							Using3-5
 3-5-3. Setup
Position Adjust the screen position if it is not aligned.
 You can only set a position in  mode. 
Digital NR When a dotted line is displayed or the screen shakes, you can view the picture with better visual qual-
ity by enabling Noise Reduction. 
Black Level If the picture seems too bright, you can set a darker black level.
 Black level is automatically set in the  input mode.
You can make the manual settings shown below only when a component signal is supplied.
 
•  : Default black level.
•  : Set the black level so it is darker.
Film Mode  Using this function, you can set the display mode optimized for playing movies.
 provides optimal display settings for movies. 
 You can only set  in  mode. 
•  - 
PC Eliminates or reduces noise that causes unstable screen quality, such as screen shaking. If the noise 
is not removed using Fine Adjustment, adjust the frequency to the maximum and then perform Fine 
Adjustment again. 
 Only activated in the PC environment. (component signals are not supported)  
•   : Used to adjust frequency and phase of PC screen automatically. 
•   : Used to adjust frequency when vertical lines appear on PC screen.
•   : Used to fine tune the PC screen. 
•   : Using this function, you can reset the PC menu settings to the factory default settings. 
Zoom Used to zoom in on the PC display screen. 
 Only activated in the PC environment. 
MENUDESCRIPTION 
						

							3-5Using
3-5-4. Option
MENUDESCRIPTION
Install To tailor the picture to the installation location, you can invert the projected images vertically/horizon-
tally. 
• : Normal Image 
• : Horizontal/Vertical Reversed Image 
• : Horizontally Reversed Image 
•  : Vertically Reversed Image 
V-Keystone  If video scenes are distorted or tilted, you can compensate for this using the vertical Keystone func-
tion. 
As the Vertical Keystone function compensates for screen distortions via software, we recommend 
installing the projector so that no screen distortions occur in the horizontal and vertical directions, 
rather than using the vertical keystone function. 
Background You can set the Background that is displayed when there is no signal from the external device con-
nected to the projector.If a signal is received, the Background you set disappears and a normal 
screen is displayed. 
•  -
Test Pattern Generated by the projector itself. Utilized as standard to optimize the installation of the projector. 
•  - You can check whether the picture is distorted or not. 
•  - You can refer to picture format sizes such as 1.33 : 1 or 1.78 : 1. 
•  - Red Screen, only for color adjustment.
•  - Green Screen, only for color adjustment.
•  - Blue Screen, only for color adjustment.
•  - White Screen, only for color adjustment. 
•  - White Screen, brings out the white tones for a more real white.
The Red/Green/Blue colors of the test patterns are only for the color adjustment procedures, and may 
not comply with the actual colors displayed during video playback.
Factory Default Using this function, you can reset various settings to the factory default.
Video TypeIn PC mode, if the projector does not recognize the type of input signal automatically and the screen 
quality is abnormal, you can select the type of input signal manually. 
•  : The type of input signal is recognized automatically.
•  : Select this when a PC providing RGB output is connected to the D-sub terminal.
•
: Select this when an AV device (STB, DVD, etc.) providing YPbPr output is connected to the D-
sub terminal. 
						

							Using3-5
MENUDESCRIPTION
Language You can select the language used for the menu screen.
 The selected language is applied to both main OSD and MEDIA PLAY menus. 
Menu Option •  : You can move Menu Position up/down/left/right. 
•  : You can set the translucency of menu. 
• < High>---
•  : You can set the display time of the menu.
• ------
Information You can check external source signals, picture setup, PC picture adjustment.  
						

							Media Play Function4-1
4 Media Play Function
4-1 Precautions on using a USB storage device 
 •This product does not support multi-card readers. 
•This product does not work if the USB storage device is connected by USB HUB. 
•Some products which do not comply with standard USB specifications might not operate normally. 
•A USB storage device with automatic recognition application or its own driver might not operate normally. 
•A USB storage device that uses only a designated driver might not be recognized. 
•Recognition speed for USB storage device may vary by device. 
•Do not turn off the product or pull a connected USB storage device out while a USB storage device is in use. Doing so may 
result in damage to the USB storage device or stored file. 
•Use a USB storage device which contains normal files. If not, it can be cause a malfunction or the files may not play. 
•USB storage devices must be formatted with FAT or FAT32(recommended) file system supported by Windows. It may not 
work normally if USB storage device is formatted with another program. 
•If USB storage device uses external power, please connect USB storage device to external power and use. 
•Use the USB cable provided with the USB device when connecting to the projector. (For more information on purchasing 
cable and external devices, contact the respective manufacturer.) 
•We do not guarantee service if a malfunction occurs with any external device caused by using a cable that does not comply 
the designated standards. 
•As the data in USB storage device can be damaged, please back up important data to avoid loss. 
•When using USB storage device with the projector, subfolders with a maximum depth of 4 from the top folder are 
supported. Also, if the number of files(including folder) in the same folder is more than 2,900, it is not recognized. It may 
also take long time to display according to the number of files. 
•Multi Partition is not supported. 
•If an external memory device does not operate after connecting to the product, try to connect it to a PC. If it still does not 
operate normally, contact the memory devices manufacturer service center or related customer center. 
•USB storage device is not writable. 
  
						

							4-2Media Play Function  
4-2Photo 
When selecting thumbnails,
You can view image files stored in a USB device.
* Press the MEDIA.P button to display the menu for the selected item.
 To use this function in your presentation, convert general word processor files to image files before saving them to a USB storage 
device.
e.g.) .ppt(Microsoft Powerpoint) 
→ .jpg /.bmp /.gif
.pdf(Adobe Acrobat) 
→ .jpg
Caution: Make sure to save image files to your USB storage device in the order of presentation.
 
MENUDESCRIPTION
Play Photo  Start Slideshow.
Play Mode •  : Plays all available image files. 
•  : Plays all image files in a selected folder. 
•  : Randomly plays all available image files in a USB storage device.
•  : Randomly plays all image files in a selected folder. 
•  : Displays an image file repeatedly.
Delete  Deletes a selected image.
Delete All Files  Deletes all image files in a USB storage device. 
						

							Media Play Function4-2
Slideshow
You can set several options while playing images.
* Press the MEDIA.P button to display the menu for the selected item.
MENUDESCRIPTION
Slideshow Setting You can set several options while playing images.
•  - 
Transition  Sets a pattern for a slide show.
•  -  -  -  -  - 
 •If the picture size is 32x32 or less,  effect is disabled.
•If you set , you cannot adjust .
•If you set ,  effect is not supported.
 
Speed  Sets a playback speed for a slide show.
•  -  - 
Play Mode •  : Plays all available image files. 
•  : Plays all image files in a selected folder. 
•  : Randomly plays all available image files in a USB storage device.
•  : Randomly plays all image files in a selected folder. 
•  : Displays an image file repeatedly.
Rotate 
Rotates an image using [ ] button on the remote control.
•  -  -  - 
Aspect Ratio  Rotates an image using direction keys on the remote control.
•  : Displays an image with its original size.
•  : Displays an image with its optimal aspect ratio.
•  : Displays an image to fit the vertical length of a screen.
•  : Displays an image as a full screen.
Background Music  •  : Plays all music files in a USB device consecutively.
•  : Stops background music.
•  : Opens the Music folder and selects background music.