Samsung Projector Sp H03 User Manual

Installation and Connection2-2
2-2 Connecting and Disconnecting the Battery
Connecting the Battery
 Align and fasten the grooves on the bottom of the projector with the counterparts on the battery.
 Push the top and back of the projector forward simultaneously until you hear a click.
Disconnecting the Battery
 Press the lock, marked [PUSH] , on the back of the battery.
 With the lock held down, lift the back of the projector. 

2-3Installation and Connection
2-3 Zoom and Focus Adjustment 
Move the [FOCUS] slide bar left or right until the picture is clear.
 The size of your screen determines the dist ance you set your projector from the screen.
If you do not place your projector at the projection distance  specified in the Screen Size and Projection Distance table in 
Section 2-4, you will not be able to adjust the focus correctly.
 
FOCUS 

Installation and Connection2-4
2-4 Screen Size and Projection Distance 
If the picture is not clear, adjust [FOCUS], or move the projector forward or backward.
SCREEN SIZE
Z (THROW DISTANCE)
M (DIAGONAL)X (HORIZONTAL)Y (VERTICAL)
INCHESCMINCHESCMINCHESCMINCHESCM
8.6 21.8 7.519.0 4.210.7 12.030.5
10 25.4 8.722.1 4.912.5 14.035.5
17.2 43.715.038.1 8.421.4 23.8 60.5
34.3 87.129.975.916.842.747.4120.5
57.2 145.3 49.9126.6 28.071.278.8200.1
85.5 217.2 74.5189.3 41.9106.5 117.7 299
90°
Z Y
X
M
Y
Z: Throw...

2-5Installation and Connection
2-5 Ventilation openings
Ventilation openings
For the location of the ventilation openings, see the picture below: 
• Do not block the ventilation openings. Blocking the ventilation openings can cause your projector to overheat and may cause 
it to fail.
NAME DESCRIPTION
,  Exhaust vents
Air outtake vent
, ,  Intake vents
Air intake vent 

Installation and Connection2-6
2-6 Supported Display Modes
2-6-1. PC Timing (D-Sub)
 All resolutions higher or lower than 854 x 480 are converted to 854 x 480 by the scaler chip in the projector. To obtain an 
optimal picture, the resolution from the PC should be similar to the projector (854 x 480).
 
2-6-2. AV Timing (VIDEO)
NTSC, NTSC 4.43, PAL, PA L60, PAL-N, PAL-M, SECAM
FORMATRESOLUTION
HORIZONTAL 
FREQUENCY
(KHZ)VERTICAL 
FREQUENCY  (HZ)PIXEL 
FREQUENCY  (MHZ)
 IBM  640 x 480  60Hz 31.469...

2-7Installation and Connection
2-7 Ports
2-7-1. Rear View
 Open the cover on the back of the projector. 
 The maximum memory capacity supported for a USB memory device is 16 GB.
(The maximum capacity supported for external memory is based on our factory test. Your experience may differ depending 
on the manufacturer of the memory device.)
 
ICONNAME
PC IN port
AV IN port
 Power port
 USB port
 Audio output port
PC IN AV IN 

Installation and Connection2-7
2-7-2. Side View
 The maximum memory capacity supported for a MicroSD(HC) card is 32 GB.
(The maximum capacity supported for external memory is based on our factory test. Your experience may differ depending 
on the manufacturer of the memory device.)
 
ICONNAME
MicroSD(HC) card slot
FOCUS 

2-8Installation and Connection
2-8 Connecting with a PC and Setting up the PC
2-8-1. Setting up the PC Environment 
Check the following items before connecting your PC to your projector.
1.Click the right mouse button on the Windows desktop, and then click [Properties]. 
The  dialog appears.
2. Click the [Settings] tab, and then set the . The optimal resolution for the projector is 800 x 600. For othe r 
resolutions supported by the projector, see the PC Timing Display Mode table in section 2-6.
 You do...

Installation and Connection2-8
• The setup process might vary depending on your type of computer or version of Windows. 
(For example, [Properties] appears instead  of [Properties (R)] as shown in 1.)
• This projector supports 32 bit color quality (per pixel) when it is used as a PC monitor.
• Projected images may differ from the images on your monitor depending on the monitor manufacturer or Windows  version.
• When connecting the projector to a PC, make sure that the PC setup complies with the display...

2-9Installation and Connection
2-9 Connecting to an AV Device
Make sure that the AV device and your projector are turned off.
1.Insert the 3RCA gender adaptor into the [ AV IN] port on the back of the projector.
2. Connect a video cable and audio cable to the 3RCA gender adaptor.
Refer to AV Timing (VIDEO) in the Supported Display Modes section for information on supported input signals.
3. Connect the video cable to the VIDEO OUT port on the AV device.
Connect the audio cable to the AUDIO OUT port on...