Samsung Projector Sp A800b User Manual

							 
To avoid injuries or damage to property, please read the following precautions carefully and use the product 
accordingly. 
The images here are for referenc e only, and are not applicable in all cases (or countries).
Failure to follow the instructions marked with this symbol may  cause personal injury or even fatality.  
Failure to follow the instructions marked with this symbol may cause personal injury or damage to the 
product or property.    
 
 
|  Power Related  | Installation Related  | Cleaning and Use Related  | 
    
 
 
  
Insert the power plug firmly so that it does not come loose. 
zWhen the connection is not firm, it may cause a fire.  
  Do not use loose power outlets  or damaged power cables. 
zThere is a danger of electric shock or fire.  
  
Under no circumstances touch the power plug with wet hands. 
zThere is a danger of electric shock.  
  Do not plug multiple devices into a single wall outlet.  
zThere is a danger of fire.  
  
Do not bend the power cord excessively or place heavy objects o n it. 
zThere is a danger of ele ctric shock or fire.  
 Before moving the product, make s ure the power is off and remove the power cord 
from the wall outlet. In addition, make sure all connection cab les are disconnected 
from other devices before moving it. 
zMoving the product without disco nnecting the power cord may damage the 
power cord and cause elec tric shock or fire.  
  
To disconnect the apparatus from  the mains, the plug must be pulled out from the  
						

							mains socket, therefore the mains plug shall be readily operable. 
zThere is a danger of ele ctric shock or fire.  
 
  
Always unplug the unit by holding the power plug. Pulling the p ower cable may 
damage the inside of it.  
zThere is a danger of fire.  
  
Unplug the power plug before cleaning the product. 
zThere is a danger of ele ctric shock or fire.  
  
 
 
 |  Power Related | Installation Related | Cleaning and Use Related | 
 
 
 
 
  TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER OPEN FLAME S 
AWAY FROM THIS PRODUCT AT ALL TIMES.  
zThere is a danger of fire.  
  
When installing the product in a  cabinet or on a shelf, make sure the front end of 
the base does not protrude. 
zDropping the product may damage it or cause injury.  
   Keep the power cord away from heaters. 
zThe coating of the pow er cord may melt and cause electric shock  or fire.  
  
Do not install the product in locations exposed to oil, smoke,  moisture or water 
(rainwater), or in a vehicle. 
zThere is a danger of ele ctric shock or fire.  
  
Do not install the product in locations with poor ventilation s uch as a bookshelf, 
closet, etc.  
zAn increase in the internal te mperature may cause a fire.   
						

							  Do not install on an unstable location, or on a stand smaller t han the product. 
zIf the product falls it may harm children. Install on a flat and stable location 
as the front part is heavy.  
   In case of thunder/lightning, di sconnect the power cord from the wall outlet. 
zThere is a danger of ele ctric shock or fire.  
 
  
Make sure the product's vents are  not blocked by a table cloth or curtain. 
zAn increase in the internal temperature may cause a fire.  
  
Place the product on th e ground carefully. 
zDoing so may cause damage or injury.  
  
Do not drop the product while carrying it. 
zDoing so may cause damage or injury.  
  Keep the product out of children’s reach. 
zIf the product falls it may caus e harm to children. Install on a flat and 
stable location as the f ront part is heavy.  
  
 
 
 
|  Power Related | Installation Related | Cleaning and Use Related | 
 
 
 
  
 Do not insert any metal such as  chopsticks, wires, gimlets, or inflammable objects 
such as paper into the vents, th e PC/COMPOSITE port, the Power  port or the Battery 
port.  
						

							zThis may cause electric shock or fire.  
If water or an alien substance enters the product, turn the product off, 
disconnect the power  cord from a wall outlet and contact a Service Center.  
  
Do not disassemble, or attempt to fix or modify the product. 
zWhen the product requires repairs, contact a  Service Center.  
  
Do not use or keep the product near flammable sprays or other s uch substances. 
zThere is a danger of f ire or explosion.  
  
Do not place containers with water, vases, drinks, chemicals, s mall metal parts or 
heavy objects on the product. 
zIf water enters the product, it m ay cause electric shock, or fire and when 
heavy objects fall, it may cause injury.  
   Do not let children place object s such as toys or cookies on th e product. 
zIf a child tries to reach for any of these objects, the product  may fall and 
cause harm.  
   Do not look directly at the ligh t of the lamp nor project the picture onto eyes. 
zThis is dangerous especially for children.  
  
When you remove batteries from t he remote, be careful that they are not swallowed 
by children. Keep batteries out of the reach of children. 
zIf swallowed, see a doctor immediately.  
 
   If the product emits smoke, unusual noise, or there is a burnin g smell,disconnect 
the power plug immediately, and contact a  Service Center. 
zThere is a danger of ele ctric shock or fire.  
  
If the power plug pin  or jack is exposed to dust, water or alie n substances, clean it 
thoroughly. 
zThere is a danger of ele ctric shock or fire.  
   
						

							Ask a Service Center  to clean the product internally at least once a year. (Charged ) 
zDust which has accumulated in the interior over an extended per iod of time 
may cause fire or a malfunction.  
   When cleaning the product, discon nect the power cord and wipe the product using 
a soft dry cloth.  
zDo not use any chemicals such as wax, benzene, alcohol, thinner s, 
insecticide, air freshener, lubricant or detergent.  
   When not using the product for a n extended period of time, disconnect the power 
plug. 
zOtherwise, this may cause heat emission from the accumulated di rt or 
degraded insulation, leading to electric shock or fire.  
  Do not install the product in places with heavy dust, chemical  substances, high or 
low temperatures, high humidity, or where it will be operated f or a long period 
continuously etc.  
  
If the product is dropped or the  casing is damaged, turn the product off and unplug 
the power cord.  
zThis may cause electric shock or fire. Contact a  Service Center.  
  
Take care not to lose the  lens cover of the product. 
zThis may damage the lens.  
  
When replacing batteries, place the batteries in the correct +/ - polarity position as 
indicated on battery holder. 
zIncorrect polarity may cause a b attery to break or leak and could lead to 
fire, injury, or contamination (damage).  
   Use only specified standard batt eries. Do not use new and used  batteries together. 
zIncorrect polarity may cause a b attery to break or leak and could lead to 
fire, injury, or conta mination (damage).  
Correct Disposal of This Product 
(Waste Electrical & Electronic Equipment) - Europe only  
						

							(Applicable in the European Union and other European countries with separate collection 
systems)  
 
This marking shown on the product or its literature, indicates  that it should not be 
disposed with other household wa ste at the end of its working life. To prevent possible 
harm to the environment or damag e to health from uncontrolled waste disposal, please 
separate this from other types of waste and recycle it responsi bly to promote the 
sustainable reuse of material resources. 
 
Household users should contact ei ther the retailer where they purchased this product, or 
their local government office, fo r details of where and how they can take this item for 
environmentally safe recycling.  
 
Business users should contact the ir supplier and check the terms and conditions of the 
purchase contract. This product s hould not be mixed with other commercial wastes for 
disposal.  
						

							 
 
 |  Product Features | Product Views  | Remote Control  | Product Specifications  | 
 
 
 
 
 
 
 
 
 Optical engine adopting advanced DLP technology  
 
  - A full 1920x1080 HD panel has been adapted.  
- A 6 segment color wheel has b
een used to implement optimal co lors. 
- 300W Lamp designed t o improve luminance
  
 
 Vivid colors  
 
  - Quality picture tuning focused
 on improving color - this unit aims at realizing color coordinates that 
meet broadcasting standards on video production.   
 
 Minimized fan noise and light leakage  
 
  - The airflow and fan installation structure are optimized to  minimize fan noise and beam leakage.
  
 
 Various Input Ports  
 
  - Abundant input terminals are available, such as the two HDMI 
(supporting HDCP) terminals and the 
two component terminals, etc., to enhance connectivity with per ipheral devices.
  
 
 User adjustments  
 
  - This unit allows adjustment of each input port. 
- The unit has a reference pattern that can be used for positio
ning and adjustment. 
- For the user's convenience in dark surroundings, a backlight  for the remote control is provided.
  
   
   
 
 
  |  Product Features | Product Views  | Remote Control  | Product Specifications  | 
 
 
 
 
  Front/Upper Side 
  
						

							 
 
 
 
 
 
  
  
1. Indicators 
- TEMP (Red LED) 
- LAMP (Blue LED) 
- STAND BY (Blue LED) 
※ Refer to the  LED Indications. 
  
2. Focus Ring 
Used for Focus Adjustment. 
  
3. Lens 
  
4.  Lens Position Moving Dial 
You can adjust screen images up and down 
within the lens range. 
※ Refer to  Adjusting the Lens Position  
Moving Dial . 
  
5. Remote Control Signal Receiver 
  
6. Adjustable Feet 
You can adjust the screen  position by moving up 
and down the adjustable feet. 
     
  
7. Zoom Knob 
Used to enlarge or r
educe image size. 
  
8. POWER( ) Button  
Used to turn the projector on or off.  
  
9. SOURCE Button  
Used to select input signals from the external 
sources. 
  
10.MENU Button  
Use this button to enter or exit a menu or to 
move forward in a menu. 
  
11. Select and Move Button(  /  ) 
Use this button to move to or select an item 
within a menu.
  
    
The buttons on the top of the p rojector are touch buttons.  
Touch them lightly with your fingers to use them. 
 Package Contents   
 
 
Quick Installation Guide  Warranty  
(Not available in all locations)  User Manual CD  
 
  
						

							   
Power Cable  Remote Control/ 2 Batteries  Cleaning Cloth 
   
   
 
 
 
   LED Indications   
 
●:Light is On    ◐:Light is Blinking    ○:Light is Off
TEMP  LAMP  STAND BY  Information 
○○ ● If you press the POWER button on 
the remote control or projector, the screen 
appears within  30 seconds.
○ ● ● The projector is in normal operating condition. 
○◐ ● This state appears when the projector is preparing an operation
 after the POWER button 
on the projector or the remote control has been pressed.
○◐ ○ The POWER button is pressed to t
urn off the projector, and the cooling system is in 
operation to cool off inside of t he projector. (Lasts for about 1 minute and 30 seconds)
◐○ ◐ Refer to Action 1 below if the c
ooling fan inside the projector is not in normal operation 
condition.
◐◐ ○ Refer to Action 2 below if the l
amp cover protecting the lamp u nit is not closed 
properly.
◐○ ○ Power is turned off automatically when temperature inside of th
e projector goes beyond 
the control limit. Refer to Action 3.
◐ ◐ ● A problem has occurred when operating the DDP IC in the prod uct. Refer to Action 4. 
◐ ◐ ◐ A problem has occurred with the operation of the lamp. Refer  to Action 5.
● ◐ ● The lifetime of the lamp has expired. Refer to Action 6.
○ ◐ ◐ The memory in the product is  not operating normally. Contact a service center .
● ◐ ◐ The power for the p roduct is not operating normally. Contact a service center .
◐● ◐ A problem has occurred when opera
ting the color wheel in the product. Refer to Action 
4.
  
  
  
  
  
    Clearing Indicator Problems   
 
Classification  State  Measures 
Action 1  When the cooling fan 
system is not in normal 
operating condition. If the symptom remains even af
ter disconnecting and then 
reconnecting the power cord and  turning the projector on again, 
contact your product provider or our  service center. 
Action 2  When the lamp cover 
protecting the lamp unit is 
not properly closed or the 
sensor system is not in 
normal operating 
condition. Check whether the screws at the bottom side of the projector ar
e 
fastened correctly. If they are abnormally fastened, contact yo ur 
product distributor or  service center. 
Adjust the installation state of your projector by referring to  the