Samsung Plasma TV PN8000GF User Manual

							English - 31
 
 
Controlling the TV with your hands using motions 
■   
 Access Motion Control
 
−  Action: Spread your hand in the direction of the camera, and shake it three or four times from a 
side to side.
 
■  
 Pointing Navigation
 Moves the cursor to the position you want.
 
−  Action: Spread your hand and guide the cursor to position you want.
 
■   
 Run
 Selects an item or executes a command that is indicated by the cursor or\
 is highlighted.
 
−  Action: Clench your fi st.
 
✎ When you watch some page or some image, you can move the page or image to direction you 
want if it can be moved. In this case, use and keep the Run  motion, and then move it to direction 
you want. To move a page, clench your fist, keep it clenched, and then move it in the direction you 
want the page to move. Note that not all pages can be moved.
 
■  
 Return
 Return to the previous menu.
 
−  Action: Spread your hand and rotate it counterclockwise.
 
■  Channel / Volume Control
 Changes the channel or adjust the volume.
 
✎ If you use the Motion Control  function while watching a channel, the channel / volume control 
screen appears.
 
−  Action: Use the Pointing Navigation motion to move the cursor to the channel or volume 
controller, and then uses the Run motion to adjust the channel or volume.
 
✎ If you use the Run motion once, it has the same effect as pressing a button on your remote. 
If you hold the Run motion, it has the same effect as pressing and holding a button on your 
remote.
 
■  
 Scroll
 Scroll the page in the direction you want. For example, suppose that you want to scroll down.
 
✎ Some applications may not support this function.
 1.  Move the cursor to the bottom of the screen (page scroll zone) using the Pointing Navigation 
motion.
 2.  Move the cursor to the center of the screen using the Pointing Navigation motion.
 3.  The page will move down.
[PE8000-ZA]BN68-04034A-00Eng.indb   312012-04-05   �� 1:22:29 
						

							English - 32
Face recognition
\231 → Tools → Settings → Account Manager → Face recognition
Enable or disable the Face recognition function. Face recognition lets you register your face with your 
Samsung account. Also, you can log in to the Samsung account using the Face recognition function 
without inputting your account ID or your account password.
 
✎You can register your face in only one account.
To register your face in your Samsung account, follow these steps:
 
✎To use this function, you must log into Smart Hub . If you don't have a Samsung Account, you 
should create one before using this function. To create your Samsung Account , refer to “Creating an 
Account” (Advanced Features → Smart Hub) in the e-Manual.
1.  On the Smart Hub screen, open the Tools menu using your remote, and then select Settings.
2.  Select Account Manager. The Account Manager screen appears.
3.  Select Face recognition. The Face recognition screen appears.
4.  Move your face into the square in the center of the screen, and then wait until the square changes from 
red to green.
 
✎If Face recognition fails, select Retry  and then try again.
5.  When done, your face is now registered in your Samsung account. The Continue to Register Service 
window appears.
 
✎To close the window, select OK . You can register services later using Link to other accounts  in 
the Smart Hub  menu (Settings  → Account Manager  → Link to other accounts ).
[PE8000-ZA]BN68-04034A-00Eng.indb   322012-04-05   �� 1:22:29 
						

							English - 33
To log in to your Samsung account using Face recognition, follow these steps:
 
✎If you use Face recognition  to log into Smart Hub, it may be less secure than logging in with a 
password.
1.  With the Smart Hub screen displayed, select a using your 
remote. The Samsung Account screen appears.
Log In
What is Samsung Account? A Samsung Account is an integrated 
membership account that lets you access all the services 
provided by Samsung through a single registered account.
Samsung Account Press [Enter]
Password Press [Enter]
Log In
Face Recognition ModeCancel
Create Account
RReturn
Remember my password
Sign me in automatically
2. 
Select Face Recognition Mode. The Face recognition screen 
appears.
 
✎To return to the Samsung Account  screen, select 
Password mode .
Log In
You can log in using facial recognition. Turn your face  towards the TV with your face level with the camera.
Password mode Pause
RReturn
3. The TV starts Face recognition. Face the front of the TV screen. The TV will recognize your face 
automatically.
 
✎A Green square indicates a registered face. A red-square indicates an unregistered face.
 
✎If the TV fails to recognize your face, try again.
4.  The TV logs you into your Samsung account automatically.
 
✎If the TV recognizes two or more registered faces, the Samsung account list appears. Select your 
account to log in.
 
✎If your face is unregistered, you can register your face in your Samsung account. Follow steps 4 
through 5 in the “To register your face to your Samsung account:” procedure above.
 
✎If you have no account, you can create one. For more detailed information, refer to “Creating an 
Account” (Advanced Features → Smart Hub) in the e-Manual.
[PE8000-ZA]BN68-04034A-00Eng.indb   332012-04-05   �� 1:22:30 
						

							English - 34
The Evolution Kit Slot (Kit Sold Separately)
This socket is designed to accept an extension device called the Evoluti\
on Kit. The Evolution Kit enables 
the TV to run a variety of the latest applications for a better user exp\
erience.
The Evolution Kit, which may not be available depending on the product, will be sold separately in 2013 or 
later.
[PE8000-ZA]BN68-04034A-00Eng.indb   342012-04-05   �� 1:22:30 
						

							English - 35
Connecting to a Network
You can set up your TV so that it can access SMART TV applications through your local area network 
(LAN) using a wired or wireless connection.
 
✎After you have “physically” connected your TV to your network, you must configure the network 
connection to complete the process. You can configure the connection during the Initial Setup 
process (see page 17 ) or after the Initial Setup process, through the TV’s menu (see page 37 ).
Network Connection - Wireless
You can connect your TV to your local area network (LAN) through a standard wireless router or modem.
The LAN Port on the Wall
LAN Cable (Not Supplied)Wireless IP Router or Modem 
that has a DHCP Server
This TV supports the IEEE 802.11a/b/g and n communication protocols. Samsung recommends using 
IEEE 802.11n. If you play video using IEEE 802.11a, b, or g, the video m\
ay not play smoothly.
Most wireless network systems incorporate a security system that requires devices that access the 
network through an access point or AP (typically a wireless router or modem) to transmit an encrypted 
security code called an access key.
Your TV is compatible with the following security protocols:
 
• Authentication Mode: OPEN, SHARED, WPAPSK, WPA2PSK
 
• Encryption Type: WEP, TKIP, AES
If you select Pure High-throughput (Greenfield) 802.11n mode and the Encryption type is set to WEP or 
TKIP on your AP or wireless router, Samsung TVs will not support a connection in compliance with new 
Wi-Fi certification specifications.
[PE8000-ZA]BN68-04034A-00Eng.indb   352012-04-05   �� 1:22:31 
						

							English - 36
Network Connection - Wired
There are three main ways to connect your TV to your network using cable, depending o\
n your network 
setup. They are illustrated starting below:
The Modem Port on the WallTV Rear Panel
LAN Cable (Not Supplied)
Modem Cable (Not Supplied) External Modem 
(ADSL / VDSL / Cable TV)
The Modem Port on the Wall External Modem 
(ADSL / VDSL / Cable TV) IP Router that has a 
DHCP Server TV Rear Panel
Modem Cable  
(Not Supplied) LAN Cable  
(Not Supplied) LAN Cable  
(Not Supplied)
The LAN Port on the Wall TV Rear Panel
LAN Cable (Not Supplied)
 
✎The TV does not support network speeds less than or equal to 10Mbps. 
 
✎Use Cat 5 or 6 (STP Type*) cable for the connection. (*Shielded Twisted Pair)
[PE8000-ZA]BN68-04034A-00Eng.indb   362012-04-05   �� 1:22:32 
						

							English - 37
Configuring Network Connections
After you have run the initial setup, you can configure or reconfigure the network connections through the 
TV's menu.
Configuring a Wireless Network Connection 
The instructions below are for networks that use the Dynamic Host Configuration Protocol (DHCP) to 
configure network connections automatically. Most wireless networks use DHCP. If you have a Static IP 
network, see the e-Manual for configuration instructions.
To configure the network connection for a network that uses DHCP, follow these steps:1.  Connect your TV to your network as shown in the illustration on page 35.
2.  Turn on your TV, and then go to the Network Settings screen. (Menu → Network → Network 
Settings)
3.  Select Start. The Network function searches for available wireless networks. When done, it displays a 
list of the available networks.
4.  In the list of networks, move the highlight to select a network, and the\
n select Next.
 
✎If you have a WPS(PBC) compatible router, select WPS(PBC)  instead, and then follow the 
directions on the screen.
5.  Enter your network security key or WPS PIN using your remote.
 
✎Enter numbers and letters using your remote.
 
• If you are using the standard remote, you can enter numbers by pressing the number buttons 
on your remote.
 
• To enter a letter, move the Highlight to the letter, and then select it. You can enter numbers in 
the same fashion if you choose.
 
✎To display capital letters (or redisplay small letters if capital letters are displayed), select Caps  or 
Shift . 
 
✎To display symbols and punctuation, select 1 F. To redisplay letters, select 1 F again.
6.  When done, select Next if you have entered a security key or WPS PIN if you have entered a WPS PIN.
7.  The TV checks the wireless connection. If the connection is successful, the “You are connected to the 
Internet. If you have any problems using online services, please contact your Internet Service 
Provider.” message appears. Select Next using your remote.
 
✎For more detailed information, see “Setting up the Wireless Network” in the e-Manual.
 
✎If you want to configure the connection manually, select IP Settings  on the Network Connection 
screen. Set IP Setting  to Enter manually, and then enter the IP Address , Subnet Mask, 
Gateway , and DNS Server  manually.
[PE8000-ZA]BN68-04034A-00Eng.indb   372012-04-05   �� 1:22:32 
						

							English - 38
Configuring a Wired Network Connection
Most home networks use the Dynamic Host Configuration Protocol (DHCP) to configure network 
connections. Home networks that support DHCP automatically provide the IP address, subnet mask, 
gateway, and DNS values your TV needs to access the Internet so you don’t have to enter them manually. 
If you have a Static IP network, see your user’s manual for configuration instructions.
To configure the network connection for a wired network that uses DHCP, follow these steps:1.  Connect your TV to your network as shown in one of the illustrations on \
page 36.
2.  Turn on your TV, and then go to the Network Settings screen. (Menu → Network → Network 
Settings)
3.  Select Start.
4.  The Network Connection screen appears, and verifies the network connection. When the connection \
has been verified, the “You are connected to the Internet. If you have any problems using online 
services, please contact your Internet Service Provider.” message appears. Network set up is 
completed.
 
✎If your TV cannot acquire network the connection values automatically or if you want to set the 
connection manually, select IP Settings  on the network connection screen. Set IP Setting  to Enter 
manually , and then enter the IP Address , Subnet Mask, Gateway, and DNS Server  manually.
 
✎For more detailed information, refer to “Setting up the Wired Network” in the e-Manual.
[PE8000-ZA]BN68-04034A-00Eng.indb   382012-04-05   �� 1:22:32 
						

							English - 39
The Smart Touch Control
Improved user convenience has been provided so that you can switch the channel and adjust the volume 
with just your fingertips while focusing on the TV screen. In addition, the built-in Touch Pad removes the 
need for a mouse when you change the menu settings and search for something on the Internet.
 
✎For more detailed information about Smart Touch Control, see "Using the Smart Touch Control" in 
e-Manual.
Smart Touch Control
TVSTBBD
RETURNVOICENUMBER
.*$
\212: Displays a list of recently used 
functions. You can select a function 
again using the Touch Pad easily and  quickly.
y: Adjusts the Volume.
Brings up the Smart Hub applications. 
See the e-Manual chapter Advanced 
Features → Smart Hub.
 
✎To exit an application that is 
running easily, press the \231 button.
Turns the TV on and off.
Touch Pad•	 Drag on the Touch Pad to move the 
focus on the screen.
•	 Click on the Touch Pad to run the 
focused item.
•	 If you don't press any button within 
30 seconds, the Smart Touch 
Control is set to Sleep mode 
automatically. To wake up the Smart 
Touch Control, press the Touch Pad.
•	 If you press and hold the Touch Pad, 
it has the same effect as pressing 
the MUTE
M button on your 
remote. However, this action scrolls 
the page on a Web Browser.
•	 Press the Touch Pad or RETURN
R 
button to return to the general 
mode.
Displays color and playing control 
functions. You can select a function 
using the Touch Pad.
Displays the shortcut functions list. You  can select a function using the Touch  Pad.
T: Quickly select frequently used 
functions. Use this button in a specific 
feature. For details, refer to e-Manual.
z: Changes channels.
RETURNR: Returns to the previous 
menu.
VOICE
\230: Lets you access the Voice 
Control function. When you press  the button, the TV displays the 
command list. You can speak using the  microphone embedded in your remote. 
 
✎For more detailed information 
about the Voice Control  function, 
see "SMART Interaction" in the  e-manual or see page 27 .
NUMBER
\232: Displays the Number 
button screen. You can select a number  using the Touch Pad. LED to show the active device. You can speak a voice command that 
displayed to the TV using MIC. To use 
MIC, press the VOICE
\230 button on your 
remote.
 
✎Voice Control  function can be 
affected recognition by unclear 
pronunciation, voice level, or 
surrounding noise.
[PE8000-ZA]BN68-04034A-00Eng.indb   392012-04-05   �� 1:22:33 
						

							English - 40
Installing batteries (Battery size : AA)
112
1. Press the back of the remote at the very bottom with both thumbs, and then slide the battery co\
ver up 
in the direction of the arrow.
2.  Install two batteries so that the polarity of the batteries (+/-) matc\
hes the illustration in the battery 
compartment.
3.  Slide the cover down in the direction of the arrow to close the battery cover.
Initial Pairing for Smart Touch Control
After you have run the Initial Setup on your TV, you should connect your Smart Touch Control to your TV. 1.  Point the Smart Touch Control toward the IR sensor of the TV and then press any button on the Smart 
Touch Control.
2.  The connection icon appears at the bottom left of the screen and the Smart Touch Control is 
automatically connected to the TV.
 
✎If you want to perform the pairing process again, press the reset button in the center of the back 
cover using a pin or the tip of an unbent paper clip. The Smart Touch Control will be initialized.
 
• Smart Touch Control PAIRING Reset button.
Calibrating the Touch Pad
To calibrate the Touch Pad on the Smart Touch Control, follow these steps: 1.  Press the NUMBER\232  button for 3 seconds. The calibration starts.
2.  When done, all the LEDs on the top of the Smart Touch Control blink twice simultaneously.
 
✎While calibrating, don't touch the Touch Pad.
 
✎If the Touch Pad looses accuracy, re-calibrate the Touch Pad by repeating Steps 1 and 2.
[PE8000-ZA]BN68-04034A-00Eng.indb   402012-04-05   �� 1:22:33