Samsung Plasma HDTV PN60E8000 User Manual

Service Provider. message appears.
WPS(PBC)  Network Setup
If your router has a WPS(PBC) 
button, you can configure your TV's 
wireless network connection using the 
WPS(PBC) button more easily.
To set up your TV's wireless network 
connection using WPS(PBC) , follow 
these steps:
1.  
Go  to  Network Settings screen. 
(Network  
→  Network Settings) 

2. 
Select  Start. The network function 
searches for available wireless 
networks. When done, it displays a 
list of the available networks.
3.  
Select  the  WPS(PBC).
4.  
Press the WPS(PBC) button on your 
router within 2 minutes. Your TV 
automatically acquires all the network 
setting values it needs and connects 
to your network.
5.  
The network connection screen  

appears, and network setup is done.
Plug & Access Network Setup The Plug & Access function lets you 
easily connect your Samsung TV to 
your Samsung wireless router (sold 
separately) by using a USB memory 
stick to transfer the setup information 
from the router to the TV. If your 
non-Samsung wireless router does 
not support Plug & Access, you 
must connect using one of the other  

methods.
 
NYou can check for equipment that 
supports Plug & Access on www.
samsung.com.
To set up your TV's wireless network 
connection using Plug & Access, follow 
these steps: 1.  
Turn on the Samsung wireless router 
and your TV.
2.  
Insert a USB memory stick into the 
USB port in your Samsung wireless  

router. Check the router’s LED’s to 
make sure it is on (Blinking → on).
3.  
Take the USB memory stick out of 
the router, and then insert it into 
a USB port on your Samsung TV. 
The memory stick downloads the 
connection information.
4.  
Wait until the connection is 
automatically established.
 
NIf  Plug & Access does not connect 
your TV to your wireless router,  

a popup screen appears on the 
screen notifying you of the failure. 
If you want to try using Plug & 
Access again, disconnect the USB 
memory stick, reset the AP, and 
then try again from Step 1. You 
can also choose one of the other 
connection setup methods.
5.  
The network connection screen 
appears, and the network setup is 
done. 

6. 
Place the wireless router in a desired 
location.
 
NIf the wireless router’s settings 
change or you install a new wireless 
router, you must perform the Plug & 
Access procedure again, beginning 
from Step 1.
Network Status
Menu  → Network
 
→  Network Status
You can check the current network and  

Internet status.
When the wireless network connection 
failed...
 
●Wireless network connection failed.
No wireless router selected. Go to 
Network Settings to select your router.
 
●Unable to connect to wireless router.
Try the following: check that the router 
is turned on, and if it is try turning it 
off and on again. Check if you need to 
enter a security key to use the router. 

 
●IP auto setting failed.
Try the following to set your IP address 
automatically. Or set your IP address 
manually by selecting IP Settings. 
- Ensure DHCP server is enabled on 
router and unplug and re-plug-in the 
router.  - Contact your Internet Service 
Provider for more information.
 
●Unable to connect to the network.
Try the following: check if your IP 
address is set correctly in  IP Settings.  

Contact your Internet Service Provider 
for more information.
 
●Connected to your local network, but 
cannot connect to the Internet.
Check the DNS settings in IP Settings, 
or contact your Internet Service 
Provider to access the Internet.
 
●Network setup complete, but cannot 
connect to the Internet.
Contact your Internet Service Provider 
to access the Internet.