Samsung Nc10 Service Guide

							
3-1
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 -
- This Document can not be used without Samsung's authorization -
NC10
3. Disassembly and Reassembly
3-1. NC10 Disassembly and assembly
PartPictureDescription
Main System
1
2
1
1.  Before disassembling the system, the AC adapter and the battery have to be separated.
2.   
As shown in picture 1, adhere KNOB to the end closely 
into the arrow direction, then push the battery up as shown in picture 2.  
3.   When the battery is pushed upwards, it can be separated.
4.  Remove the BOTTOM screw. IF only keboard is disassembled, remove only 3 BOTTOM screws(ㅁ mark).
M2 x L8, Silver (15EA)
5. Remove the DOOR-MEMORY.
[Caution] Attention to red sentence.

Winchester_NC10_Eng.indb   12008-09-20   오후 1:36:02 
						

							
3-2
3. Disassembly and Reassembly
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 -
- This Document can not be used without Samsung's authorization -
NC10

PartPictureDescription
Main System
6.  Remove the memory by pushing the fixed-tap out. 
7.  Push the Hook up inwards by using a pin-set as shown in the picture, and then lift the key board up. 
[Notice]
When  you  push  the  hook  up,  you  have  to  be  careful  not  to scratch Topdp.
    
As shown in the picture, lift the top side of keyboard up and then disassemble keyboard.
8.   Lift the Keyboard up, and then take the FPC out after lifting the Connector Lock.  
     
Take Keyboard FPC cable out after opening Keyboard 
connector Lock.

Winchester_NC10_Eng.indb   22008-09-20   오후 1:36:13 
						

							
3-3
3. Disassembly and Reassembly
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 -
- This Document can not be used without Samsung's authorization -
NC10

PartPictureDescription
Main System
9.  
As shown in the picture, separate the BOTTOM-COVER(LAN Connector side first) by widening the gap between the BOTTOM-COVER and the TOP. (Be careful not to make scratch in the gap using a wooden-driver.)
     
As shown in the picture, separate the BOTTOM-COVER 
by widening the gap between the BOTTOM-COVER and the TOP. (Be careful not to make scratch in the gap using a wooden-driver.)
10.   
After removing the Screw for fixing HDD remove the INSULATOR by lifting the HDD up to about 70 degrees direction.   
[Notice]
When  you  life  the  HDD  up,  you  shall  not  enforce  excessive strength.
11.  Speaker CONN. INT Mic CONN., Power S/W CONN. Touch-Pad FPC.

Winchester_NC10_Eng.indb   32008-09-20   오후 1:36:22 
						

							
3-4
3. Disassembly and Reassembly
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 -
- This Document can not be used without Samsung's authorization -
NC10

PartPictureDescription
Main System
12.  Remove the Antenna Cable which is connected with wireless LAN, and then remove the Screw which fixes WLAN. [Aux(Black)]    
M2 x L4, Black (1EA)
1. White, Main 2. Black, Aux 
13.  Remove the Bluetooth Camera Cable and the LCD cable CONN. and disassemble the W/L Antenna Cable.
14.  Remove the Screw which fixes the Main Board and the TOP and then separate Main Board from TOP.
 M2 x L4, Black (2EA)
15.  Remove the both sides of Screw, which fasten the Hinge and the TOP.
 M2 x L4, Black (4EA)
16. Stand the Top Ass’y in a vertical direction.

Winchester_NC10_Eng.indb   42008-09-20   오후 1:36:32 
						

							
3-5
3. Disassembly and Reassembly
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 -
- This Document can not be used without Samsung's authorization -
NC10

PartPictureDescription
Main System
17.  Separate the Top Ass'y from the LCD.
18.  Remove the Screw which fixes the SIM Card Sub-board and the Main-Board, and then separate them.
 M2 X L4, Black (2EA)
19.  Remove the Screw (3 EA) which connects the RHE and the Main board and separate them.  
 M2 X L4, Black (3EA)
20.   Remove the RHE as shown in the picture.  

Winchester_NC10_Eng.indb   52008-09-20   오후 1:36:41 
						

							
3-6
3. Disassembly and Reassembly
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 -
- This Document can not be used without Samsung's authorization -
NC10

PartPictureDescription
LCD Ass'y
21.  Remove the RHE as shown in the picture.  
 M2 X L4 (4EA)
[Notice]
When  you  remove  the  Rubber-LCD-Cap,  be  careful  not  to scratch the Front..
22.  Insert your hand into the gap of the LCD Back and the LCD front and then separate first, the upper part of the LCD Front and second, the both sides of the LCD Front then finally the bottom part of it.  
 M2 X L4 (4EA)
23. Remove the both sides of Hinge Cover.
24.  Conditions after removing the both sides of Hinge Cover.

Winchester_NC10_Eng.indb   62008-09-20   오후 1:36:42 
						

							
3-7
3. Disassembly and Reassembly
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 -
- This Document can not be used without Samsung's authorization -
NC10

PartPictureDescription
LCD Ass'y
25.  Remove the Screw as shown in the picture. 
 M2 X L4 (4EA)
26.  Separate the Hinge and the LCD-Panel as shown in the  picture. (When you separate the Hinge, remove the Hinge after lifting the LCD-Panel up.)
27.  Dis-assemble the LCD-Cable and then remove the LCD Panel.  
28.  Separate the Camera Module and the Cable as shown in the picture.

Winchester_NC10_Eng.indb   72008-09-20   오후 1:36:45 
						

							
3-8
3. Disassembly and Reassembly
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 -
- This Document can not be used without Samsung's authorization -
NC10

PartPictureDescription
LCD Ass'y
29.  Remove the Tape inside the circle.   
30.  Pull the LCD cable up to the arrow direction and then separate it.
21-2.   Method to disassemble LCD without disassembling Main System. As shown in the picture, Stand the Top Ass’y in a vertical direction. remove 4 Rubber-LCD-Cap and 4 screws
          M2 X L4 (4EA) 
22-2.  Insert your hand into the gap of the LCD Back and the LCD front and then separate first, the upper part of the LCD Front and second, the both sides of the LCD Front then finally the bottom part of it. After that, remove screw(4ea) as shown in the picture. 
    M2 X L4 (4EA)
22-3.  
As shown in the picture, LCD can be disassembled from LCD Cable and Camera moduel also can be disassembled.  LCD Cable and Camera moduel disassembling method refer to No 28.

Winchester_NC10_Eng.indb   82008-09-20   오후 1:36:56 
						

							
3-9
3. Disassembly and Reassembly
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 -
- This Document can not be used without Samsung's authorization -
NC10

PartPictureDescription
TOP Ass'y
31.  Remove the Bluetooth Module.   
32.    Remove the Speaker Cable and the Speaker.  
33. Remove the MIC.
34. Remove the Molding.

Winchester_NC10_Eng.indb   92008-09-20   오후 1:37:02 
						

							
3-10
3. Disassembly and Reassembly
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 -
- This Document can not be used without Samsung's authorization -
NC10

PartPictureDescription
TOP Ass'y
35.  Remove the Power S/W Ass’y.
36.    Confirm the arrow mark for assembly direction on the Power S/W Sub board.
37.  Check the Guide in which the Power S/W at bottom will be inserted, then you have to assemble the Power S/W.

Winchester_NC10_Eng.indb   102008-09-20   오후 1:37:04