Samsung ML 1867 User Manual

							FunctionDescription
Power On/OffPress this button to turn the power on or off. 
Cancel print jobDuring printing, press this button once. The 
prin
t job is cleared from both the machine and 
the computer and then the machine returns to 
the ready mode. This may take some time 
depending on the size of the print job.
 If you press this button for more than 2 
seconds, the power goes off. 
Introduction _ 21
Turning on the machine
1.Plug in the power cord.
2. Pr
ess  on the control panel.
 If you want to turn the power off, press and hold this button for 
about 2 seconds.
Downloaded From ManualsPrinter.com Manuals 
						

							Getting started_ 22
2.getting started
This chapter gives you step-by-step  instructions for setting up the USB connected machine and software.
This chapter includes:
•Setting up the hardware
• Printing a configuration sheet
• Supplied software •
System requirements
• Installing USB connected machine’s driver
• Sharing your machine locally
  
Setting up the hardware
This section shows the steps to set up the hardware, as is explained in the 
Quick Install Guide. Make sure you read the Quick Install Guide first and 
follow the steps below:
Location
1.Select a stable location.
Select a level, stable place with adeq uate sp
 ace for air circulation. Allow 
extra space for opening cover(s) and tray(s). 
The area should be well ventilated and away from direct sunlight or 
sources of 
 heat, cold, and humidity. Do  not set the machine close to the 
edge of your desk or table.
Printing is suitable for altitudes under 1,000 m (3,281 ft). 
Place the machine on a flat, stable su rface so th
 at there is no incline 
greater than 2 mm (0.08 inch). Otherwise, printing quality may be 
affected.
2. Unpack the machine and check all the enclosed items.
3. Remove tape
  holding the machine securely.
4. In
stall the toner cartridge.
5.Loa
d paper. (See  Loading paper in the tray on page  29.)
6. Ma
ke sure that all cables are connected to the machine. 
7.Turn
 the machine on. (See  Turning on the machine on page  21 .)
 
This machine will not operate when the power main fails.
Printing a configuration sheet
Print a configuration page to make su re that the machine is operating 
properly.
To print a configuration page:
In the ready mode, press and hold 
 for about 10 seconds until the green 
LED blinks slowly, and release. 
Supplied software
After you have set up your machine and  connected it to your computer, you 
must install the printer software. If  you
  are a Windows or Macintosh OS 
user, install the software from the supplied CD and if you are a Linux OS 
user, download the software from the Samsung website 
(www.samsung.com/printer) and install.
 Machine software is occasionally updated for reasons like the release 
of new operating system  
 and etc. If needed, download the latest 
version from the Samsung webs ite (w ww.samsung.com/printer).
OSContents
Windows •Print
er driver:  Use this driver to take full advantage of 
you
r machine’s features.
• Easy Printer Manager:  This program combines device 
settings as well

 as printing environments, settings/actions 
and launching. All of these features provide a gateway to 
conveniently use your Samsung machine.
• Print
er Status:  This program monitors and informs you 
of th
e machine status.
Macintosh •Print
er Driver:  Use this driver to take full advantage of 
you
r machine’s features.
• Smart Panel:  This program allows you to monitor the 
machi

ne’s status.
Linux •Unif
ied Linux Driver:  Use this driver to take full 
ad
vantage of your machine’s features.
• Smart Panel:  This program allows you to monitor the 
machi

ne’s status and alerts you when an error occurs 
during printing.
Downloaded From ManualsPrinter.com Manuals 
						

							Getting started_ 23
System requirements
Before you begi n, ensure that your  system meets the following 
requirements:
Windows
Your machine supports the fo llowing Windows operating systems.
OPERATING 
SYSTEMRequirement (recommended)
CPURAMfree HDD 
space
Windows® 
200
 0 Intel® Pentium® II 400 
MHz (Pe
ntium III 933 
MHz) 64 MB 
 
(128 MB) 600 MB
Windows® XP Intel® Pentium® III 933 
MHz (Pe

ntium IV 1 GHz) 128 MB  
(256 MB)1.5 GB
Windows 
Serv
 er® 2003 Intel® Pentium® III 933 
MHz (Pe
ntium IV 1 GHz) 128 MB  
(512 MB)1.25 GB to  
2 GB
Windows 
Server®  2008 Intel® Pentium® IV 1 GHz 
(Pentiu

m IV 2 GHz) 512 MB  
(2048 MB)10 GB
Windows 
Vista® Intel® Pentium® IV 3 GHz
512 MB  
(1024 MB)15 GB
Windows® 7 Intel® Pentium® IV 1 GHz 
32

-bit or 64-bit processor 
or higher 1 GB (2 
GB)
16 GB
• Supp
ort for DirectX® 9 graphics with 128 MB 
memory (to enable the Aero theme).
• DVD-R/W Drive
Windows 
Serv
 er® 2008 
R2 Intel® Pentium® IV 1 GHz 
(x86) or 1.4 GHz (x64) 
proce
ssors (2 GHz or 
faster) 512 MB  
(2048 MB)
10 GB
 •
Internet Explorer 5.0 or higher is  the minimum requirement for all 
Windows operating systems.
• Wi
ndows Terminal Services  is compatible with this machine.
Macintosh
OPERATING 
SYSTEMRequirements (recommended)
CPURAMfree HDD space
Mac OS X 
10.3 ~ 10
 .4•
Intel® 
Processors
• PowerPC G4/ G5 •
128 MB for a 
PowerPC based 
Mac (512 MB)
• 51
2 MB for a 
Intel-based Mac 
(1 GB) 1 GB Mac OS X 
10.5
•
Int
el® 
Processors
• 867
 MHz or 
faster Power PC 
G4/ G5 512 MB (1 GB)
1 GB
Mac OS X 
10.6 •
Int
el® 
Processors 1 GB (2 GB)
1 GB
Linux
ItemRequirements
Operating 
syste
 m RedHat Enterprise Linux WS 4, 5
Fedora 4, 5, 6, 7, 8, 9, 10, 11, 12
SuSE Linux 10.0, 10.1
OpenSuSE 10.2, 10.3, 11.0, 11.1, 11.2 
Mandriva 2005, 2006, 2
007
 , 2008, 2009, 2009.1 
Ubuntu 5.04, 5.10, 6.06, 6. 10
 , 7.04, 7.10, 8.04, 8.10, 
9.04, 9.10, 10.04
SuSE Linux Enterprise Desktop 10, 
 11
Debian  4.0, 5.0 
CPU Pentium IV 2.4 GHz (Intel Core™2)
RAM 512 MB (1024 MB)
Free HDD space 1 GB (2 GB)
Installing USB connected machine’s driver
A locally connected machine is a machine directly connected to your 
computer by a USB cable.
 Only use a USB cable no longer than 3 m (10 ft.).
Windows
You can install the machine software  using the typical or custom method.
The following steps are recommended for most users who use a machine 
di
 rectly connected to your computer. All components necessary for machine 
operations will be installed.
1. Make
 sure that the machine is connected to the computer and powered 
on.
 If the “ Found New Hardware Wizard ” window appears during the 
installation procedure, click  Cancel to close the window.
2. Inse
rt the supplied software CD into your CD-ROM drive.
•The
 software CD should automatically run and an installation window 
will appear.
• If th
e installation window does not appear, click  Start and then  Run. 
Type X:\ Setup.exe , replacing “X” with the letter which represents 
your CD-ROM Drive. Click  OK.
• If yo
u use Windows Vista, Windows  7 and Windows 2008 Server R2 
click  Start  > All programs  > Accessories >  Run.
Type X:\ Setup.exe  
 replacing “X” with the letter which represents 
your CD-ROM Drive and click  OK.
• If
 the  AutoPlay  window appears in Windows Vista, Windows 7 and 
OPERATING 
SYSTEMRequirements (recommended)
CPURAMfree HDD space
Downloaded From ManualsPrinter.com Manuals 
						

							Getting started_ 24
Windows 2008 Server R2, click  Run Setup.exe  in Install or run 
program  field, and click  Continue or Yes  in the  User Account 
Control  windows.
3. Select  In
 stall now.
If necessary, select a language from the drop-down list.
 The Advanced Installation  has an option, Custom Installation . 
The  Custom Installation  allows you to select the machine’s 
connection and choose individual component to install. Follow the 
instruction on the window.
4. Read
 the  License Agreement , and select I accept the terms of the 
License Agreement . Then, click Next.
The software searches for the machine.
 If your machine is not connected to the computer, the following  window will appear.
•
After connecting the machine, click  Next.
• Ch
eck if you want to install the software without 
connecting the printer to the network or locally.
- Che
ck this option to install the software without a machine 
connected. In this case, the print a test page window will be 
skipped.
• Searc
h again
-Press 
this button to research for the connected machine.
-Wh
en you click this button, the firewall notice window 
appears;
Turn off the firewall and click  Se
 arch again. For Windows 
operating system, click  Start > Control Panel  > Windows 
Firewall , and inactivate this option. 
Then click  Next in
  the Firewall Notice window. 
Turn off the firewall from the third partys program beside 
the oper
 ating system. Refer to  the manual provided by 
individual programs.
• Help
- Th
is help button gives detailed information about how to 
connect the machine.
5. The
 searched machines will be shown on the screen. Select the one you 
wish to use and click  Next.
 If the software searched only one machine, the confirmation 
window appears.
6. After the
  installation is finished, a window asking you to print a test page 
appears. If you want to print a test page, click  Print a test page.
Otherwise, just click  Next and 
 skip to step 8.
7. If 
the test page prints out correctly, click Yes .
If not, click  No to r
 eprint it.
8. If you wan
 t to register your machine on Samsung web site, click  On-line 
Registration .
9. Click  Fi
nish .
 If the printer driver does not work properly, follow the steps below to 
uninstall and reinstall the driver. 
a) Make sure that 
 the machine is connected to your computer and 
powered on.
b)  F
rom the  Start menu, select  Programs or All Programs > 
Samsung Printers  > your printer driver name  > Uninstall .
c)  Sele
ct the necessary option and follow the instructions in the 
window.
Downloaded From ManualsPrinter.com Manuals 
						

							Getting started_ 25
d) After uninstalling the printer driver, reinstall it (see “Installing USB 
connected machine’s driver” on page 23).
Macintosh
The software CD that came with your  machine provides you with the PPD 
file that allows you to use the CUPS driver or Apple LaserWriter driver (only 
available when you use a machine which supports the PostScript driver) for 
printing on a Macintosh computer. 
1. Ma
ke sure that the machine is conne cted to your computer and powered 
on.
2. In
sert the supplied software CD into your CD-ROM drive.
3.Doub
le-click the CD-ROM icon that  appears on your Macintosh desktop.
4. Doub
le-click the MAC_Installer  folder.
5. Doub
le-click the Installer OS X  icon.
6. Enter the
  password and click  OK.
7. The
 Samsung Installer window opens. Click  Continue.
8. Read
 the license agreement and click  Continue.
9. Click  Agr
 ee to agree to the license agreement.
10. Select  Easy Insta
 ll and click  Install. Easy Install  is recommended for 
most users. All components necessary for machine operations will be 
installed. 
If you select  Cus
 tom Install, you can choose individual components to 
install.
11. Whe
n the message which warns that all applications will close on your 
computer appears, click  Continue.
12. After th
e installation is finished, click  Quit.
13. Ope
n the Applications  folder > Utilities > Print Setup Utility .
• Fo
r Mac OS X 10.5~10.6, open the  Applications folder > System 
Preferences  and click Print & Fax .
14. Click  Add on th
 e Printer List .
• Fo
r Mac OS X 10.5~10.6, click the “ +” icon; a display window will pop 
up. 
15. For Mac OS X 
 10.3, select the USB tab. 
• For 
Mac OS X10.4, click  Default Browser and find the USB 
connection.
• For 
Mac OS X 10.5~10.6, click  Default and find the USB connection.
16. For Mac OS X 
 10.3, if Auto Select  does not work properly, select 
Samsung  in Printer Model  and your machine name in  Model Name.
• Fo
r Mac OS X 10.4, if Auto Select does not work properly, select 
Samsung  in Print Using  and your machine name in  Model. 
• Fo
r Mac OS X 10.5~10.6, if Auto Select does not work properly, 
select  Select a driver to use...  and your machine name in  Print 
Using . 
Your machine appears on the  Printer List, 
 and is set as the default 
machine.
17. Click  Add.
 If the printer driver does not work properly, uninstall the driver and 
reinstall it. 
Follow steps below to uninstall the driver for Macintosh.
a)Ma
ke sure that the machine is connected to your computer and 
powered on.
b) In
sert the supplied software CD into your CD-ROM drive.
c)Doub
le-click CD-ROM icon that appears on your Macintosh 
desktop.
d) Doub
le-click the  MAC_Installer folder.
e) Doub
le-click the  Installer OS X icon.
f) Ente
r the password and click  OK. g)
T
he Samsung Installer window opens. Click  Continue.
h) Select  Uninsta
 ll and click  Uninstall. 
i) When
 the message which warns that all applications will close on 
your computer appears, Click  Continue.
j) W
hen the uninstall is done, click  Quit.
Linux
You need to download Linux software packages from the Samsung website 
to install the pr inter software. 
Follow the steps below to install the software.
Installing the Unified Linux Driver
1. Make sure that the machine is connected to your computer and 
powered on.
2. W
hen the  Administrator Login  window appears, type in root in the 
Login  field and enter the system password.
 You must log in as a super user (root) to install the machine 
software. If you are not a s uper user, ask your system 
administrator.
3. From th
 e Samsung website, download the Unified Linux Driver 
package to your computer.
4. Righ
t click the  Unified Linux Driver package and extract the 
package. 
5. Doub
le click  cdroot > autorun .
6. Whe
n the welcome screen appears, click Next .
7.When the installation is complete, click  Finish.
The installation program added the Un ifie
 d Driver Configurator desktop 
icon and the Unified Driver group to the system menu for your 
convenience. If you have any difficulties, consult the on screen help that 
is available through your system menu or from the driver package 
Windows applications, such as  Unified Driver Configurator.
 If the printer driver does not work  properly, uninstall the driver and 
reinstall it. 
Follow the steps below steps to uninstall the driver for Linux.
a) Ma
ke sure that the machine is connected to your computer and 
powered on.
b) W
hen the Administra tor Login window appears, type in “root” 
in the  Login field and enter the system password.
You must log in as a super user (root) to uninstall the printer 
driver. If you are 
 not a super user, ask your system 
administrator.
c) Click the icon
  at the bottom of the desktop. When the Terminal 
screen appears, type in:
[root@localhost root]#cd / opt
 /Samsung/mfp/uninstall/
Downloaded From ManualsPrinter.com Manuals 
						

							Getting started_ 26
[root@localhost uninstall]#./uninstall.sh
d) Cli
ck  Uninstall .
e) Cli
ck  Next. 
f) Cli
ck  Finish.
Installing the SmartPanel
1.Make sure that the machine is connected to your computer and 
powered on.
2. Wh
en the Administrator Login  window appears, type in root in the 
Login  field and enter t he system password.
 You must log in as a super user  (root) to install the machine 
software. If you ar e not a super user, ask your system 
administrator.
3. Fro
m the Samsung we bsite, download the Smart Panel package to 
your computer.
4. Rig
ht click the Smart Panel pa ckage and extract the package. 
5. Dou
ble click  cdroot > Linux  > smartpanel >  install.sh.
Sharing your machine locally
Follow the steps below to set up computers to share your machine locally.
If the Host computer is directly connected to the machine by a USB cable 
a

nd is also connected to the local ne twork environment, the client computer 
connected to the local network can use the shared machine through the 
host computer to print. 
 
1Host computer A computer which is directly connected to 
the 
machine by USB cable.
 
2Client computers Computers which use the machine shared 
th
rough the host computer. 
Windows
Setting up a host computer
1. Install your printer driver (See  Installing USB connected machine’s 
driver on page  23 ).
2. Cli
ck the Windows  Start menu. 
3. Fo
r Windows 2000, select  Settings > Printers .
• F
or Windows XP/2003, select  Printers and Faxes. 
• F
or Windows 2008/ Vista, select Control Panel  > Hardware and 
Sound  > Printers . 
• For Windows 7, select Co
 ntrol Panel > Hardware and Sound  > 
Devices and Printers . 
• F
or Windows Server 2008 R2, select  Control Panel > Hardware 
>  Devices and Printers . 
4. Rig
ht-click the printer icon. 
5.Fo
r Windows XP/2003/2008/Vista, press  Properties.
For Windows 7 and Windows Server 2008 R2, from context menus, 
select the  Printer p

roperties.
 If Printer properties  item has a ► mark, you can select other 
printer drivers connected  with the selected printer.
6. Select the  Sharing ta
 b.
7. Check  Ch
 ange Sharing Options .
8. Check th
 e Share this printer  checkbox.
9. Fil
l in the  Share Name field. Click OK.
Setting up a client computer
1. Install your printer driver (See  Installing USB connected machine’s 
driver on page  23 ).
2. Click th
e Windows Start  menu. 
3. Select  Al
 l programs > Accessories  > Windows Explorer .
4. Enter the
  IP address of the host computer in the address bar and 
press Enter in your keyboard. 
 In case host computer requires a  User name and Password , 
fill in User ID and password  of the host computer account.
5. Righ
t click the printer icon you want to share and select  Connect.
6. If a se
t up complete message appears, click  OK. 
7. Ope
n the file you want to print and start printing. 
Macintosh
 The following steps are for Mac OS X 10.5~10.6. Refer to Mac Help 
for other OS versions. 
Setting up a host computer
1.Install your printer driver. (See  Macintosh on page 25 .)
2. Ope
n the Applications  folder > System Preferences  and click 
Print & Fax . 
3. Select
 the printer to share in the  Printers list. 
4. Select  Sh
 are this printer .
Setting up a client computer
1.Install your printer driver. (See  Macintosh on page 25 .)
2. Ope
n the Applications  folder > System Preferences  and click 
Print & Fax . 
3. Click the “ +” icon. 
A display window showing the name of your shared printer appears.
4. Select y
 our machine and click  Add. 
Downloaded From ManualsPrinter.com Manuals 
						

							Basic setup_ 27
3.basic setup
After installation is complete, you may want to set the machine’s default settings. Refer to the next section if you would like 
to set or change values. This chapter gives you step-by-step instructions for setting up the machine.
This chapter includes:
•Setting the default tray and paper  
Setting the default tray and paper
You can select the tray and paper you would like to keep using for printing 
job.
From your computer
Windows
1.Click the Windows Start menu. 
2.For Windows 2000, select Settings > Printers.
•For Windows XP/2003, select Printer and Faxes. 
•For Windows 2008/Vista, select Control Panel > Hardware and 
Sound > Printers. 
•For Windows 7, select Control Panel > Hardware and Sound > 
Devices and Printers. 
•For Windows Server 2008 R2, select Control Panel > Hardware 
> Devices and Printers. 
3.Right-click on your machine.
4.For Windows XP/2003/2008/Vista, press Printing Preferences.
For Windows 7 and Windows Server 2008 R2, from context menus, 
select the Printing Preferences.
 If Printing Preferences item has a ► mark, you can select 
other printer drivers connected with the selected printer.
5.Click Paper tab. 
6.Select tray and its options, such as paper size and type.
7.Press OK.
 If you want to use special-sized paper such as a billing paper, 
select Edit... in the Paper tab in the Printing Preferences. (See 
Opening printing preferences on page 34.)
Macintosh
Macintosh does not support this function. Macintosh users need to 
change the default setting manually each time they want to print using 
other settings. 
1.Open a Macintosh application and select the file you want to print.
2.Open the File menu and click Print.
3.Go to Paper Feed pane.
4.Set appropriate tray from which you want to print.
5.Go to Paper pane.
6.Set paper type to correspond to the paper loaded in the tray from 
which you want to print.
7.Click Print to print. 
Linux
1.Open Terminal Program.
2.When the Terminal screen appears, type in the following: 
[root@localhost root]# lpr 
3.Select Printer and click Properties…
4.Click on the Advanced tab.
5.Select the tray (source) and its options, such as paper size and type.
6.Press OK.
Using The power saving feature
When you will not be using the machine for a while, you can use this feature 
to save power. 
1.Install the driver (See Installing USB connected machine’s driver on 
page 23).
2.Select Start > Programs or All Programs > Samsung Printers > 
Samsung Easy Printer Manager > Samsung Easy Printer Manager.
3.Select Device Settings > Machine > Power Save. 
4.Select a time you want from the drop-down list.
5.Click Save.
Downloaded From ManualsPrinter.com Manuals 
						

							Media and tray_ 28
4.media and tray
This chapter provides information on how  to load print media into your machine.
This chapter includes:
•Selecting print media
• Changing the tray size
• Loading paper in the tray •
Printing on special media
• Changing the tray size
  
Selecting print media
You can print on a variety of print me dia, such as plain paper, envelopes, 
labels, and transparencies. Always use print media that meets the 
guidelines for use with your machi ne and from the appropriate tray. 
Guidelines for selecting the print media
Print media that does not meet the gui delines outlined in this user’s guide 
may cause the following problems:
• Poor print qua
 lity
• In
creased paper jams
•Pre
mature wear on the machine.
•Permanen
 t fuser damage, not covered under warranty.
Properties, such as weight, compositio n
 , grain, and moisture content, are 
important factors that affect the  machine’s performance and the output 
quality. When you choose print materials, consider the following:
• The
 type, size and weight of the print media for your machine are 
described in print media specifications. (See  Print media specifications 
on page  62.)
• Desired
  outcome: The print media you choose should be appropriate for 
your project.
• Bri
ghtness: Some print media are whiter than others and produce 
sharper, more vibrant images.
• Surfa
ce smoothness: The smoothness of the print media affects how 
crisp the printing looks on the paper.
 •Some print media may meet all of the guidelines in this section and 
still not produce satisfactory results.  This may be the result of the 
sheets characteristics, impro per handling, unacceptable 
temperature and humidity levels,  or other variables over which 
cannot be controlled.
• Befo
re purchasing large quantities of print media, ensure that it 
meets the specifications in this us er’s guide and that it meets your 
output requirements. 
 
• Using print media that does not  meet these specifications may 
cause problems, requiring repairs. Such repairs are not covered by 
the warranty or service agreements.
The amount of paper put into the tray may differ according to 
me
 dia type used. (See  Print media specifications on page  62.)
• Using
 inflammable print media can cause a fire.
•Use desig
 nated print media (See  Print media specifications on 
page  62 ).
 
The use of inflammable media or foreign materials left in the printer 
may lead to overheating of the unit and, in rare cases may cause a 
fire.
Media sizes supported in each mode
ModeSizeTypeSource
Simplex 
printing For details about 
pape
r size, see 
Print media 
specifications 
on page  62. For details about 
pa
per type, see 
Print media 
specifications 
on page  62 .Tray
Duplex 
printing 
(Manual)
a
a. 75 to 90 g/m2 (20~24 lbs bond) only (See  Print media specifications 
on page  62 ). Letter, A4, 
Lega

l, US Folio, 
Oficio Plain, Color, 
Preprin
ted, 
Recycled, Bond, 
Archive Manual feeding 
in the tray
Changing the tray size
The tray is preset to Letter or A4 size, depending on your country. To 
change the size, you need to adjust the paper guides.
1
Paper width guide
2Tray
3Paper length guide
Downloaded From ManualsPrinter.com Manuals 
						

							Media and tray_ 29
1.Open front cover and pinch the paper length guide and pull it out to 
extend the tray.
 Because the machine is very light, it can move when you open and 
close the tray or install and remo ve the toner cartridge. Be careful 
not to move the machine when performing these tasks.
2. Fle
x or fan the edge of the paper  stack to separate the pages before 
loading the paper. Insert the paper into the tray.
3. Load paper with the print side facing up. Make sure that all four corners 
are flat in the tray.
 Do not overload the tray with p aper. Otherwise, it may cause paper 
jams.
4. Pinch 
the paper length guide to adjus t the guide so that it is flush up 
against the rear edge of the paper;  then pinch the paper width guides so 
they are flush against the sides of the paper.
 • Do not push the paper width guid e too far causing the media to 
warp. 
• Do no
t use a paper with more than 6  mm (0.24 inch.) curl. 
• If you do no
 t adjust the paper wid th guide, it may cause paper  jams.
Loading paper in the tray
Tray
1.
Open the front cover, pinch the paper length guide and pull it out to 
extend the tray. Then, adjust the tray size to the media size you are 
loading. (See  Changing the tray size on page  28 .)
2. F
lex or fan the edge of the paper stack to separate the pages before 
loading papers.
3.Place the paper with the side you want to print facing up.
When you print a document, set the paper type and size for the tray.
For information about setting the paper type and size on the control 
p

anel (See  Setting the default tray and paper on page  27).
 • If you experience problems wit h paper feeding, check whether 
the paper meets the media specifications. Then, try placing 
one sheet at a time in tray (See  Print media specifications on 
page  62 , Printing on special media on page  30).
• The
 settings made from the machine driver override the 
settings on the control panel.
Manual feeding in the tray
The tray can hold special sizes and types of print material, such as 
postcards, note cards, and envelopes. It is useful for single page printing on 
letterhead or colored paper.
Tips on using the manual feeding method
•If you select  Paper > Source  > Manual Feeder  from your printer 
driver, you need to press 
 each time you print a page.
Load only one type, size and weight of p
 rint media at a time in the 
tray.
• To pre
vent paper jams, do not add media while printing. 
•Pri
nt media should be loaded face up with the top edge going into 
the tray first and be placed in the center of the tray.
Downloaded From ManualsPrinter.com Manuals 
						

							Media and tray_ 30
•Always load the use recommended print media to avoid paper jams 
and print quality problems. (See  Print media specifications on 
page  62.)
• Fl
atten any curl on postcards, envelopes, and labels before loading 
them into the tray.
1. Loa
d the paper in the tray.
 •When printing on special media, you must follow the 
loading guideline. (See  Printing on special media on 
page  30 .)
• W
hen paper does not feed well while printing, gently push 
the paper in manually until it  starts feeding automatically. 
2. Sque
eze the tray paper width guides and adjust them to the width of 
the paper. Do not force them too much, or the paper will bend 
resulting in a paper jam or skew.
3. Op
en the output support. 
4.To
 print from an application, open  the application and open the print 
menu.
5. Op
en  Printing Preferences . (See Opening printing preferences on 
page  34.)
6. Cli
ck on the Paper  tab in Printing Preferences, and select an 
appropriate paper type.
 For example, if you want to use  a label, set the paper type to 
Label .
7. Select  Manu
 al Feeder in paper source, then press  OK.
8. Sta
rt printing.
 If you are printing multiple pages,  load the next sheet after the first 
page prints out, and press the 
. Repeat this step for every page 
to be printed.
Printing on special media
The table below shows the available special media for printing. 
 When printing on a special media, we recommend you feed one paper 
at a time. Check the ma ximum input number of media for tray. (See 
Print media specifications on page  62.)
TypestrayManual feeding 
in traya
Plain ●●
Thick ●●
Thin ●● Cotton
●
Color ●
Preprinted ●
Recycled
●●
Envelope●
Transparency●
Labels●
CardStock●
Bond●
Archive●●
(● : supp
orted, Blank:  Not supported) 
The following media types are shown in the  Prin
 ting Preferences. This 
paper type option allows you to set the type of paper to be loaded in the 
tray. Selecting the appropriate medi a will let you get the best printout 
quality. Selecting inappropriate medi a can result in poor print quality.
• Plain:  Normal plain paper. Select this type if your printing on 60 to 120 
g/

m2 (16 to 32 lbs).
• T
hick:  90 to 163 g/m2 (24 to 43 lbs) thick paper.
• Th
in:  60 to 70 g/m2 (16 to 19 lbs) thin paper.
• C
otton:  75 to 90 g/m2 (20 to 24 lbs) cotton paper.
• Co
lor:  75 to 90 g/m2 (20 to 24 lbs) color-back grounded paper.
• Pr
eprinted:  75 to 90 g/m2 (20 to 24 lbs) preprinted/letterhead paper.
• R
ecycled:  60 to 90 g/m2 (16 to 24 lbs) recycled paper.
 When you use recycled paper, printouts might be wrinkled and/or 
jamming may occur due  to excessive curl. 
• C
ardStock:  105 to 163 g/m2 (28 to 43 lbs) cardstock. 
• En
velope:  75 to 90 g/m2 (20 to 24 lbs) envelope.
• Tr
ansparency:  138 to 146 g/m2 (37 to 39 lbs) transparency paper. 
• Labels:  120 to 150 g/m2 (32 to 40 lbs) labels. 
• Bo
nd:  105 to 120 g/m2 (28 to 32 lbs) bond. 
• Ar
chive:  70 to 90 g/m2 (19 to 24 lbs) If you need to keep the print-out 
for a long time, such as for archives. 
a. Load one paper at a time.
TypestrayManual feeding 
in traya
Downloaded From ManualsPrinter.com Manuals