Samsung Ht Tz222r User Manual

							21
ENG
●  CONNECTIONS
 
Connect the front, Centre and Subwoofer speakers to the  
1. 
DVD Player, referring to page 18~19.
With the DVD Player turned off, insert the TX card into the   
2. 
TX Card Connection (WIRELESS) on the back of the main unit.
Hold the TX card so that the slanted side faces to the left   
•	
and insert the card into the port. 
The TX card enables communication between the main   
•	
unit and the wireless receiver. 
Connect the left and right rear speakers to the wireless  
3. 
receiving module. 
Plug the power cord of the wireless receiving module  
4. 
in the wall outlet 
AUX IN 2
Slanted side face leftTX card
Do not insert any other card except the provided TX card.    
`
If a different TX card is used, the product may be damaged or the card may not be 
removed easily.
Do not insert the TX card upside down or in the reverse direction.
 
`
   Insert the TX card when the DVD Player is turned off. Inserting the card when it is turned    
`
on may cause a problem.
If the TX Card is inserted and wireless receiving module setting is complete, sound is not 
 
`
output from the Rear Speaker connectors on the main unit.
  The wireless receiving antenna is built into the wireless receiver module. Keep the unit 
 
`
away from water and moisture.
For optimal listening performance, make sure that the area around the wireless receiver 
 
`
module location is clear of any obstructions.
If no sound is heard from the wireless rear speakers, switch the mode to DVD 5.1  
`
channel or Dolby ProLogic II .
In 2-CH mode, no sound will be heard from the wireless rear speakers. 
`
 
 
MPlace the wireless receiver module at the rear of the listening position. If the wireless  
`
receiver module is too close to the main unit, some sound interruption ma\
y be heard due 
to interference.
If you use a device such as a microwave oven, wireless LAN Card, Bluetooth equipment, 
 
`
or any other device that uses the same frequency (5.8/2.4GHz) near the system, some 
sound interruption may be heard due to interference.
The transmission distance from the main unit to the wireless receiving module is about 33 
 
`
feet (10m), but may vary depending on your operating environment. If a steel-concrete wall 
or metallic wall is between the main unit and the wireless receiver module, the system may 
not operate at all, because the radio wave cannot penetrate metal.
If the main unit doesn't make wireless connection, the system needs ID Setting between 
 
`main unit and wireless receiver module.With the main unit turned off, press remote 
control's number buttons "0" "1""3""5" and main unit will turn on. With the wireless 
receiver module turned on, press "ID SET" button on the back of the wireless receiving 
module for 5 seconds.
 
						

							22
Connections
CONNECTING THE VIDEO OUT TO YOUr TV
Choose one of the three methods for connecting to a TV.
AUX IN 2
FM ANT
METHOD1   METHOD2
    (supplied)
METHOD3
METHOD 1 : HDMI
Connect the HDMI cable (not supplied) from the HDMI OUT jack on the back of the DVD Player to the 
HDMI IN jack on your TV.HDMI enables you to view movies in High Definition on your HDTV.
METHOD 2 : Composite Video
Connect the supplied Video cable from the VIDEO OUT jack on the back of the DVD Player to the 
VIDEO IN jack on your TV.
METHOD 3 : Scart
If your television is equipped with a SCART input, connect a SCART (not supplied) from the AV OUT jack 
on the back panel of the main unit to the SCART IN jack on your television.  
VIDEO SELECT Function  
Press and hold the Number 0 (VIDEO SEL.) button on the remote control for over 5 seconds.
 or  will appear in the display. At this time, press the 
•	 Number 0 (VIDEO SEL.) 
button shortly to select between  and .
If Scart (RGB Input) is equipped for your TV, press the 
•	 Number 0 (VIDEO SEL.) button to select RGB 
mode.  
You can get a better picture quality by using Scart setting.
If Scart (RGB Input) is not equipped for your TV, press the
•	  Number 0 (VIDEO SEL.) button to select 
COMPOSITE mode.
 
MResolutions available for the HDMI output are 480p(576p), 720p,1080i/1080p. 
`
This product operates in Interlace scan mode 576i(480i) for component output.\
 
`
If you use an HDMI cable to connect a Samsung TV to the DVD Player, you can operate the Home  
`Cinema using the TV's remote control. This is only available with SAMSUNG TV's that support 
Anynet+(HDMI-CEC).
If your TV has the  
`  logo, then it supports the Anynet+ function.
  
						

							23
ENG
●  CONNECTIONS
HDMI Auto Detection Function
The player's video output will automatically change to HDMI mode when co\
nnecting an HDMI cable 
while power is on.HDMI (High Definition Multimedia Interface)
•	
HDMI is an interface that enables the digital transmission of video and \
audio data with just a single connector.  
Using HDMI, the DVD Home Cinema transmits a digital video and audio sign\
al and displays a vivid 
picture on a TV having an HDMI input jack.
HDMI connection description
•	
HDMI connector - Supports video and digital audio data.
- HDMI outputs only a pure digital signal to the TV.
-  If your TV does not support HDCP (High-bandwidth Digital Content Protection), random noise 
appears on the screen.
Why does Samsung use HDMI?
•	
Analogue TV's require an Analogue video/audio signal. However, when playing a DVD, the data 
transmitted to a TV is digital. Therefore either a digital-to-Analogue converter (in the DVD Home 
Cinema) or an Analogue-to-digital converter (in the TV) is required. During this conversion, the picture 
quality is degraded due to noise and signal loss. HDMI technology is sup\
erior because it requires no 
D/A conversion and is a pure digital signal from the player to your TV.
What is the HDCP?
•	
HDCP (High-band width Digital Content Protection) is a system for protecting DVD content outputted 
via HDMI from being copied. It provides a secure digital link between a video source (PC, DVD. etc) 
and a display device (TV, projector. etc). Content is encrypted at the source device to prevent 
unauthorized copies from being made.
What is Anynet+?
•	
Anynet+ is a convenient function that offers linked operation of this unit through Samsung TV's with 
the Anynet+ feature.
-  If your Samsung TV has an 
 logo, then it supports the Anynet+ function.
-       If you turn on the player and insert a disc, the player will start playing the dis\
c, and the TV will turn on 
automatically and switch to HDMI mode.
-   If you turn on the player and press the Play button with a disc already inserted, the TV will 
immediately turn on and switch to HDMI mode.
HDMI FUNCTION
resolution Selection
This function allows the user to select the screen resolution for 
HDMI output.
In Stop mode, press and hold the SD/HD (Standard 
Definition/High Definition) button on the remote control.
Resolutions available for the HDMI output are 
•	
576p(480p), 720p, 1080i/1080p.
SD(Standard Definition) resolution is 576p(480p) and HD  
•	
(High Definition) resolution is 720p, 1080i/1080p.
 
MIf the TV does not support the configured resolution,  
`
you will not be able to see the picture properly.
When a HDMI cable is connected, composite(Video)  
`
and component video signals are not output.
See your TV owner's manual for more information on 
 
`
how to select the TV's Video Input source. Why use HDMI (High Definition 
Multimedia Interface)? 
This device transmits a DVD 
video signal digitally without 
the process of converting to 
Analogue. You will get sharper 
digital pictures when using an 
HDMI connection.
  
						

							24
Connections
HDMI FUNCTION
Using Anynet+(HDMI-CEC)
Anynet+ is a function that enables you to control other Samsung 
Devices with your Samsung TV's remote control.  Anynet + can be 
used by connecting this Home Cinema to a SAMSUNG TV using a 
HDMI Cable. This is only available with SAMSUNG TV's that support 
Anynet+.
Connect the main unit of the Home Cinema to a Samsung TV 
1. 
with an HDMI cable. (See page 22)
Set the Anynet+ function on your TV.  
2. 
(See the TV instruction manual for more information.)
You can operate the Home Cinema by using the TV remote control. 
•	
(Available TV buttons : 
, , , ,  , and  , buttons,~ button)
If you select the TVSet the Anynet+(HDMI-CEC) to On by pressing the Anynet+ button on your 
TV remote control.
• 
receiver : On : You can listen to audio through the Home Cinema.• receiver : Off : You can listen to audio through the TV.
If you select the THEATrESelect THEATrE to connect and set the option of each item below.• View TV : If Anynet+(HDMI CEC) is set to on and you select  
                    View TV, the home cinema will automatically  
                     switch to digital in mode.
• Theatre Menu : You can access and control the Home cinema menu.
• Theatre Operation :   The Home Cinema disc playback information will 
be displayed.  
You can control the Disc operation of the Home 
Cinema such as title, chapter and subtitle 
change.
• Receiver : On : You can listen to audio through the Home Cinema.
• Receiver : Off : You can listen to audio through the TV.
 
MIf you choose 'View TV' and want to listen to TV sound through Digital In, you have to connect  
`an optical cable between the TV and the Home Theatre.
With Anynet+
You can operate this unit, power 
on your TV, or watch a movie by 
pressing the Play button on your 
Samsung TV's remote control.
Move Ent
er
Exit
SetupConnected to Playe rOff  On   
View T VTHEA TER
THEATER Menu
MOVEENTEREXIT
MOVEENTEREXITMove Ent
er
Exit
SetupConnected to Playe rOff  On   
View T VTHEA TER
THEATER Menu
MOVEENTEREXIT
BD Wise (Samsung products only)
You can select to use the BD Wise menu only if the Samsung home 
theatre is connected to a Samsung TV that supports BD Wise using an 
HDMI cable.
What is BD Wise?
•	
BD Wise automatically adjusts BD Wise-compliant Samsung products to the 
optimal settings between them.This feature is enabled only if BD Wise-
compliant Samsung products are connected to each other using an HDMI 
cable.
To use BD Wise
•	
Use an HDMI cable to connect the Samsung home theatre to a BD 
1. 
Wise-compliant Samsung TV.
Set each BD Wise menu of the Samsung home theatre and the Samsung TV to On, respectively.
2. 
   - This will optimize the picture quality according to the content (In the disc, DVD, etc) that you    
      want to play.
     - This will also optimize the picture quality between the home theatre and your BD Wise-compliant     
       Samsung TV.
 
MIf you want to change the resolution in BD Wise mode, you must set BD mode to Off in advance. 
`
If you set the BD Wise mode to off, the resolution of the connected TV will be adjusted to its   
`maximum resolution automatically.
BD Wise will be disabled if the player is connected to a device that does no\
t support BD Wise.
 
`
BD WISE              :   ON
HDMI VIDEO OUT:    RGB              
TV DISPLAY         :    WIDE/HDTV              
PARENTAL           :    OFF              PASSWORD         :    CHANGE              
LANGUAGE
MOVE ENTEREXIT
RETURN
 
						

							25
ENG
●  CONNECTIONS
Optical Cable
(not supplied)
OPTICAL : rear Panel
External Analogue Component
FM ANTFM ANT
AUX : Connecting an External Analogue Component
Analogue signal components such as a VCR. 
Connect AUX IN  (Audio) on the Home Cinema to the Audio Out of the ext\
ernal Analogue      
1. 
   component.
   Be sure to match connector colours.  
•	
 
Press the 
2.  AUX button on the remote control to select AUX input. 
You can also use the
•	  FUNCTION button on the main unit.  
           The mode switches as follows :   
           DVD/CD ➞ D.IN  ➞ AUX   ➞ USB   ➞ FM.
 
M  
You can connect the Video Output jack of your VCR to the TV, and connect the Audio  
`
Output jacks of the VCR to this product.
OPTICAL : Connecting an External Digital Component
Digital signal components such as a Cable Box/Satellite receiver (Set-Top Box).
Connect the Digital Input (OPTICAL) on the Home Cinema to the Digital \
Output of the external  
1. 
  digital component.
Press the 
2.  AUX button on the remote control to select DIGITAL IN.
 You can also use the 
•	 FUNCTION button on the main unit to select D-IN. 
The mode switches as follows :   
DVD/CD ➞ D.IN  ➞ AUX ➞  USB   ➞ FM.
External Digital Component
Audio Cable (not supplied)
If the external Analogue 
component has only one Audio 
Out, connect either left or right.
CONNECTING AUDIO FrOM EXTErNAL COMPONENTS
AUX : rear Panel
  
						

							26
Connections
CONNECTING THE FM ANTENNA
 
Connect the FM antenna supplied to the FM 75
1.  Ω COAXIAL Jack.
Slowly move the antenna wire around until you find a location where reception is good, then    
2. 
fasten it to a wall or other rigid surface.  
 
M   This unit does not receive AM broadcasts.   
`
 
Cooling Fan
The cooling fan supplies cool air to the unit to  prevent overheating.
Please observe the following cautions for your safety.
Make sure the unit is well-ventilated. If the unit has poor ventilation, the tem\
perature inside the unit may rise   
•	
and may damage it.
Do not obstruct the cooling fan or ventilation holes. (If the cooling f\
an or ventilation holes are covered with a 
•	
newspaper or cloth, heat may build up inside the unit and fire may result.)
FM ANT
FM ANT
FM ANT
FM Antenna(supplied)
  
						

							27
ENG
The DVD Home Cinema's remote can be used to control Samsung TV's.
Plug the main unit's power cord into the AC power supply.
1. 
Press the 
2.  DVD rECEIVEr button to operate the DVD Home 
Theatre.
 
 
Press the 
3.  FUNCTION button on the main unit or DVD button  
on the remote to enable DVD/CD playback. 
Press the 
4.  TV button to set the remote to TV mode. 
Press the 
5.  POWEr button to turn on your Samsung TV 
 with this remote.  
Press the 
6.  SOUrCE button to select VIDEO mode  
on your TV. 
Before using your home theatre
VIDEO
FUNC.
Selecting the Video Format
Press and hold the Number 7 button on the remote controller for over 5 seconds while the 
power is turned off.
By default, the video format is set to "PAL".
•	
"NTSC" or "PAL" will appear in the display. At this time, press the 
•	
Number 7 button shortly to select between "NTSC" and "PAL".
Each country has a different video format standard. 
•	
For normal playback, the video format of the disc must be the same 
•	
as the video format of your TV.
   
						

							Playback
28
DISC PLAYBACK
dB
 
Press the 
1.  OPEN/CLOSE (     )  button to open the disc tray.
Load a disc.
2. 
Place a disc gently into the tray with the disc’s label 
•	
facing up.
Close the compartment by pressing the 
3.  OPEN/CLOSE (     ) 
button again.
Playback starts automatically.
•	
 
To stop playback, press the STOP (
)  button during playback.
 
If pressed once, 
•	 PrESS PLAY is displayed and the stop position will be stored in memory.    
If the PLAY (
) button or ENTEr button is pressed, playback resumes from the stop position.   
(This function works only with DVDs.)
  If pressed twice, 
•	 STOP is displayed, and if the PLAY (
) button is pressed, playback starts from the 
beginning.
 
To temporarily pause playback, press the 
PAUSE () button during playback.
 
To resume playback, press the 
•	 PLAY () button. 
 
MThe initial screen may appear different,depending on the content of the disc. 
`
Pirated discs will not run in this player because it violates the CSS (\
Content Scrambling System :    
`a copy protection system) recommendations.
STANDBYFUNC.
  ASCCD RIPPING
     
						

							29
ENG
●  PLAYBACK
MP3/WMA-CD PLAYBACK
Data CDs (CD-R, CD-RW) encoded in MP3/WMA format can be played.
A
Place the MP3/WMA disc on the disc tray.
1. 
The MP3/WMA menu screen will appear and  
•	
playback will start.
The appearance of the menu depends on the  
•	
MP3/WMA disc.
  WMA-DRM files cannot be played.
•	
In Stop mode, use the Cursor 
2.  , , ,  button   
to select the album, and then press the ENTEr button.
Use the Cursor 
•	 ,  button to select the track.
To change the album, use the Cursor 
3.  , , ,   
button to select another album in Stop mode, and then 
press the ENTEr button.
Press the 
4.  STOP 
(      ) button to stop playback.
 
MSome MP3/WMA-CDs may not play, depending on the recording mode. 
`
Table of contents of a MP3-CD varies depending on the MP3/WMA track forma\
t recorded  
`
on the disc.
Press the Cursor 
•	 , , ,  button when it is in Stop mode and select a desired icon from the 
top part of the menu.  
   
Music File Icon : To play music files only, select the 
 Icon. 
Image File Icon : To view image files only, select the 
 Icon.  
Movie File Icon : To view movie files only, select the 
 Icon.  
All File Icon : To view all files select the 
 Icon.
To play a file icon in the screen,
   
						

							Playback
30
JPEG FILE PLAYBACK
Images captured with a digital camera or camcorder, or JPEG files on a PC can be stored on a CD and then played back 
with this Home Theatre.
Slide Mode G
Place the JPEG disc on the disc tray. 
Playback starts automatically. Each image is displayed  
•	
for 5 seconds and then the next image is displayed.
Press the [,]  button to skip to the next slide. 
Each time the button is pressed, the slide moves backward or forward.
•	
rotate/Flip Function G
Press the Cursor  , , ,  button during playback.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
MThe maximum resolutions supported by this product are 5120 x 3480 (or 19.0 MPixel) for  
`
standard JPEG files and 2048 x 1536 (or 3.0 MPixel) for progressive image files. 
button: Rotate 90°  
Clockwisebutton: Rotate 90° 
Counterclockwise
button: Flip Vertically
button: Flip Horizontally
Original Image
ENTER SELECT