Samsung Ht Dl200 Instruction Manual

							Using Disc Menu/Title
20
Repeat Playback 
19
Playing Repeatedly 
Each time the Repeat button is pressed 
Repeat playback allows you to repeat a chapter, title, or track.
A↔B Repeat Playback 
Press the Repeat AB button again.
1
2
Repeat
A   BRepeat
Title 
Press the Repeat button.
To Select the Disc Menu Press the Menu button during
playback.
1
Use the Up/Down ( /  ) or
Left/Right(      /      ) button to
access the different features.Press the Enter button.
2
• The selected item will play.
• The Menu Screen appears.• When playing a VCD version
2.0, you can operate it using
PBC On/Off function.
3
Menu
You can use the menus for the audio language,
subtitle language, profile, etc. DVD menu contents
differ from disc to disc.
For DVDs containing multiple titles, you can
view the title of each movie.
Depending on the disc, this function may either
not work at all, or may work differently.Using the Title Menu
• Repeat playback operation is not possible with version 2.0 VCD discs if PBC is turned on.
To operate this feature, press the MENU button, and then select PBC OFF.
Press the  Repeat A
↔B button at the
beginning (A) of the segment you want to
review. 
Press the Repeat A↔B button again at
the end (B) of the segment you want to
review. 
• The segment will begin repeating.To return to normal playback 


 
						

							22
Program Playback
21
To Program Tracks in a particular order To Cancel the Programming 
PROGRAM MENU SELECT : ENTERTITLE CHAPT
PREVIOUS NEXTTITLE CHAPT2 3 4 5 
678 9 10 
1 PLAY :  FINISH : PROGRAM
TITLE CHAPT
PREVIOUS NEXTTITLE CHAPT2 1 3 4 5 
678 9 10 
1 PROGRAM MENU SELECT : ENTER
FINISH : PROGRAM PLAY : 
TITLE CHAPT
PREVIOUS NEXTTITLE CHAPT2 3 4 5 
678 9 10 
1 2 1 PROGRAM MENU SELECT : ENTER
FINISH : PROGRAM PLAY : 
TITLE CHAPT
PREVIOUS NEXTTITLE CHAPT3 4 5 
678 9 10 
1 1 2 
2 PROGRAM MENU SELECT : ENTER
FINISH : PROGRAM PLAY : 
TITLE CHAPT
PREVIOUS NEXTTITLE CHAPT2 
3 
4 
5 6
7
8 
9 
10 1 2  1 
2  1 
7  1 
3  2 
4 2 1  4 
2  6 
4  3 
5  5 
2  1 PROGRAM MENU SELECT : ENTER
FINISH : PROGRAM PLAY : 
Press the Program button.
1
Press the Enter button then
use the Number buttons to
select the desired title.
23
• You can use  also just the
Left/Right (     /      / 
 /  ) button. 
Press the Enter button, then use
the Number buttons to select the
desired chapter.
Press the Enter button.
4
At this time, you can continue
programming if you want to.
5
• When programming more than
10 tracks, select            and
then press the Enter button.
The program selection screen
where you can program up to
10 additional tracks appears.
• The selected track number is 
programming and the cursor
moves to the next number.
• Press the Stop (     ) button twice during playback.• Press the Stop (     ) button once when in the Stop mode.• Press the Open/Close (     ) button on the main unit. 
The disc tray will open and then close. 
The program will then be deleted.
To Playback the
Tracks in the
Programmed Order Press the Play/Pause 
(       ) button.
Press either the Program button or Stop (    ) button.
To Change the Program Press the Up/Down( /  )
button to select the track
number to be changed.
123
• The cursor moves to the next
number when the Enter button
is pressed again.
Press the Enter button.
4
Repeat steps 1-4 above to
change the program.
5
• The cursor moves to the
number below.
You can program or change
particular tracks for VCD or CD
discs in the same manner.• You can use also just the
Left/Right (      /     ) button.
• You can use also just the
Left/Right
(     /      / 
 /  ) button.
NEXT
To delete the entire Program
When you have entered a
wrong number 
Clear
Press the Clear button.• When you want to delete a selection during
programming, select the track (or chapter, or title) to be
deleted and then press the Clear button.
Program
Use this function with video and music CDs to play the tracks in a particular order.
Press the Enter button to
select the title or chapter to be
changed.Press the Clear button and
then press the Number
buttons.             



 
						

							• Depending on the disc, DTS or DIGITAL PRO LOGIC can be
selected.
24 23
OFF1/3
2/33/3
To enlarge an image • Images can be enlarged 2x and 4x.• During DVD playback, press the Zoom button
to zoom in 2X/4X/normal, in that order.• Press 
/      /  / to move the enlarged
portion you want to watch.
• This function only works with discs on which multiple angles have been recorded.• During playback, press the Angle button to select the desired angle in 1/3, 2/3, 3/3,
normal, in that order.Selecting the desired Screen Angle
Various DVD Functions
Selecting the Audio Language/Subtitle Language
Selecting the Audio Language 
V I D E O
OFF 1/1
KOR KOR
ENG
JAP 
1/3
2/3
3/3
• Depending on the number of languages recorded on a DVD disc, a
different audio language (KOREAN, ENGLISH, JAPANESE, etc.) is
selected each time the button is pressed.Selecting the Subtitle Language
V I D E O
OFF
1/1
1/1
ENGKOR
JAP
OFF 
KOR
1/3
2/3
3/3
• Depending on the number of languages recorded on a DVD disc, a
different subtitle language (KOREAN, ENGLISH, JAPANESE, etc.)
is selected each time the button is pressed.• To make the subtitles disappear, select OFF.
2ZoomTV System
Angle
AudioMO/STSubtitle
Press the Zoom button.
Press the Angle button. Press the Audio button.
Press the Subtitle button.
• The word       INVALID appears on the TV screen!• If this message appears on the TV screen while buttons are being
operated, that operation is not possible with that particular disc.• Depending on the disc, the audio or subtitle language function
may not work.
TITLE V I D E O
1/2
1/8
00:00:00
T
C 
CHAPTERV I D E O
1/2
1/8
00:00:00
TC 
TIMEV I D E O
1/2
1/800:00:00
TC ::
To move directly to a title, chapter, or time 
• Each The desired scene is
located and then played.• Depending on the disc, the Title
function may not work.
• Each time the button is pressed, it repeats as shown below.
Press the Go To button.
1
Press Number(0~9) button or the
Left/Right (     /     ) button.
2
Go To

• Only 2X zoom
operation is
possible during
VCD playback.

 
						

							26
4:3 LB
OFF
RATING LEVELBITSTREAM
OUTPUT  DIGITAL  TV SCREEN 
 : Move                           Setup : ExitLANGUAGES SYSTEM 
Select when you want to watch a 16:9 screen ratio DVD movie on a TV with a 4:3 ratio screen.
You can see the full 16:9 picture, but black bars will appear at the
top and bottom of the screen.
You can only view the central portion of the 16:9 screen.
You can view in wide screen  but the top and bottom of the  picture
will be cut off.
• However if the movie is recorded in 4:3 ratio, you cannot view the full 16:9 picture with the
above functions.4:3PS4:3LB16:9
TV SCREEN(TV SCREEN RATIO)
4:3 LB
OFF
BITSTREAM
OUTPUT  DIGITAL  TV SCREEN 
RATING LEVEL : Move                           Setup : ExitLANGUAGES SYSTEM 
The Rating Level function works in conjunction with DVDs which have been assigned
a rating, to help control the type of DVD that your family watches.1. Select RATING LEVEL, then press the
Enter button.
4:3 LB
BITSTREAM
OUTPUT  DIGITAL  TV SCREEN 
RATING LEVEL : Move                           Setup : ExitLANGUAGES SYSTEM 
2. Use the number(0~9) buttons to input
a 4-digit password.• The player’s password is set to 7890 by
default.
OUTPUT  DIGITAL  TV SCREEN 
RATING LEVEL : Move                           Setup : ExitLANGUAGES SYSTEM 
4:3 LB
3.Use the Up/Down (
 /  )
button to select either RATING LEVEL or
NEW PASSWORD, and then press the Enter button.
• There are up to 8 rating levels on a disc.• If LEVEL 6 is selected, a disc which contains rating LEVEL 7 and above cannot
be played.• If you select NEW PASSWORD, the screen changes and enables you to enter
the new password.
RATING LEVEL
While the player is in the stop
mode, hold the Stop (     ) button
down on the main unit for more than
5 seconds.• INITIAL appears on the display and
all default settings will return to
Factory Preset.When the rating level
password has been forgotten
You can use the DVD players Setup function to select the TV screen ratio,
rating limit, or digital output mode.
25
System Setup 
• Move to the detailed items.• Then press the Left (     ) button to return to the previous step.
ENGLISH
CHINESE
CHINESE
CHINESE OSD LANGUAGE SYSTEM 
AUDIO 
SUBTITLE
MENU LANGUAGE LANGUAGES 
 : Move                                Setup : Exit
4:3 LB
OFF
BITSTREAM
OUTPUT  DIGITAL  TV SCREEN 
RATING LEVEL
 : Move                           Setup : Exit
LANGUAGES SYSTEM 
4:3 LB
OFF
RATING LEVELBITSTREAM
OUTPUT  DIGITAL  
 : Move                           Setup : Exit
LANGUAGES SYSTEM 
TV SCREEN 
4:3 LB
OFF
RATING LEVEL
OUTPUT  DIGITAL   TV SCREEN 4:3 PS
16:94:3 LB
 : Move                           Setup : Exit
LANGUAGES SYSTEM 
OFF
RATING LEVEL
BITSTREAM
OUTPUT  DIGITAL  TV SCREEN 
 : Move                           Setup : Exit
LANGUAGES SYSTEM 
4:3 LB
Press the Up/Down (  /  ) button 
to select the
desired sub-item 
and then press the Enter
button.
45
From the stop mode, press
the Setup button. 
1
Press the Left/Right (     /     )
button to select the system.Press the Up/Down (  /  )
button to select the desired
item.
23
To End the System Setup
Setup
• Press the Setup button again.To Set up the System 
Setup
Press the Enter button or Right (     ) button.



 
						

							28
Controlling a TV with the RemoteThe remote can also be set up to control most TVs. To program the remote, use the code that
corresponds to your brand.
1
Turn on the TV.
DVD TUNER 
BandAUX TV
Display Return
DVD/CD/TUNER
Volume
DSP Mode123
456
78
0Zoom
A   B
9Sound Edit
SPK Mode
Pro Logic
Slow
Angle
RepeatTest Tone Setup
TV System
RepeatProgram
RemainClear
Step
Effect Mute SleepGo To TV/VIDEO Title Menu
ChannelSubtitle Audio
MO/ST
Volume
Enter
+
Tuning
Down Up
D.R.C
2
Point the DVD’s remote at the TV.
27
Setting up the Language Features Using the DVD players Setup function, you can customize the Menu
Language, Subtitle Language, and Disc Menu Language.
To set up the language feature 
12
• Move to the language features.• Then press the Left (     ) button to return the previous step.
ENGLISH
CHINESE
CHINESE
CHINESE OSD LANGUAGE SYSTEM 
AUDIO 
SUBTITLE
MENU LANGUAGE LANGUAGES 
 : Move                                Setup : Exit
AUDIO 
SUBTITLEOSD LANGUAGE 
MENU LANGUAGE
AUDIO 
SUBTITLE OSD LANGUAGE 
MENU LANGUAGE
 : Move                                Setup : Exit
ENGLISH
CHINESE
CHINESE
CHI NESE SYSTEM  LANGUAGES 
MENU LANGUAGE : Move                                Setup : Exit
ENGLISH
CHINESE
CHINESE OSD LANGUAGE SYSTEM 
AUDIO 
SUBTITLE LANGUAGES ENGLISH
CHINESE
FRENCH
GERMAN
JAPANESE 
MENU LANGUAGE : Move                                Setup : Exit
ENGLISH
ENGLISH CHINESE
CHINESE OSD LANGUAGE SYSTEM 
AUDIO 
SUBTITLE LANGUAGES 
(PLAYER MENU LANGUAGE)(AUDIO LANGUAGE)
(SUBTITLE LANGUAGE)
(DISC MENU LANGUAGE)
34
Press the Setup button from the stop mode.To End the Language Features Setup 
Setup
• Press the Setup button again.
Setup
Press the Up/Down (  /  ) button  to select
the desired item.
Press the Enter button or Right (     ) button.Press the Up/Down (  /  ) button to select
the desired language and then press the Enter
button.


• If your TV does not switch
from VIDEO mode to TV
mode, press the TV
POWER
(        )
button
twice.
• The remote may not be
able to control every
model TV of the brands
listed.
Dynamic range compression (DRC) function• The selection switches back and forth between 
“D.R.C. ON” and “D.R.C. OFF” each time the 
button is pressed.• This function only works when in the Dolby Digital mode.
D.R.C
Press the D.R.C button.This function allows for fullness of sound with Dolby Digital effect even
when playing at low volumes during nighttime listening.
TITLE  
TUNED
PROGRAM PBC
MHZKHZ
SURROUND DSP 
ST
PRO LOGICLINEAR  PCM
LCR
LSLFE
SRSD I G I T A L
4
If the TV turns off, setup is complete.
33
While holding the            button down, enter the code for
your brand.
TV
example: For SAMSUNG 1TVs
While holding down the            button, 
enter                     .
TV
Code
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
SAMSUNG 1
SHARP 2
SONY
MAGNAVOX
SANYO 1
LG 2
RCA
LG 1
TOSHIBA
HITACHI
JVC
PANASONIC 1
MITSUBISHI 2
SAMSUNG 2
SAMSUNG 3SHARP 3
ZENITH
LG 3
DAEWOO 8
SANYO 2
EMERSON
SHARP 3
SAMSUNG 4
MATSUSHITA
NOBLEX
TELEFUNKEN
NEWSAN
LOEWE
RCA2
16
17
18
19
20
21
22
23
24
25
26
27
28
29 Brand Code Brand
 
						

							Speaker Setup
2930
•When 5.1 Channel Surround Sound is played, you
can enjoy the best sound if the distance between
you and each speaker is the same. You can set
Delay Time in the Center/Rear Speaker to
customize the sound to the acoustics of your room.• Setting Center Speaker
If the distance of Dc is equal to or longer than the
distance of Df in the figure, set the mode as 0ms.
Otherwise, change the setting according to the
table on the table.• Setting Rear Speakers
If the distance of Df is equal to the distance of Ds
in the figure, set the mode as 0ms.
Otherwise, change the setting according to the
table.To set the delay time
Df Dc
Ds
Speaker Setting Methods
V I D E O
Distance of (A)
50
100
400
200
Value(ms)
1.3
2.6
3.9
5.3
Distance of (B)
200
400
600
Value(ms)
5.3
10.6
15.9
(A)=Df-Dc
(B)=Df-DsDc: Distance from center speaker to
listening position
Df :  Distance from front speakers to
listening position
Ds: Distance from rear speakers to
listening position
Ideal Center Speaker Position
Ideal Rear Speaker Position
Arrange all speakers within a circle
as shown in the figure.
Front SpeakersCenter SpeakerRear SpeakersSubwoofer SpeakerSet the front speakers so that their tweeters (high-range) are
aligned at about ear level and at a horizontal angle of 45°to the
prime listening position.
Ideally the center speaker should be positioned with its top
surface flush with the front speakers. However, you may place
the speaker either on top or near the bottom of your TV set.Place the subwoofer at any convenient location within
the vicinity of the listening position. Set the rear speakers further back parallel to the walls, at
60 to 90 centimeters (2 to 3 feet) above prime listening
position ear level.
If the space behind the listening position is insufficient
(i.e., too close to the wall), place the rear speakers facing
each other on either side.
Setting up Speaker Mode and Delay Time• Each time the button is pressed, a different mode selection is
displayed on the front panel display as shown below.
SPK Mode
The display changes depending on the current audio output mode
(DSP, PRO LOGIC, 3-STEREO, STEREO, etc.).
F SP SMALLC SP SMALLR SP SMALLSW SP USEC DEL MSR DEL MS
D I G I T A L
LCR
LSLFE
RS
D I G I T A L
LCR
LSLFE
RS
D I G I T A L
LCR
LSLFE
RS
D I G I T A L
LCR
LSLFE
RS
D I G I T A L
LCR
LSLFE
RS
D I G I T A L
LCR
LSLFE
RS
S
p
e
a
k
e
r
M
o
d
eDelay 
Time
Front speaker: Small
Center speaker: Small
Rear speaker: Small
Subwoofer: Use
Center Speaker Delay Time
Rear Speaker Delay Time
C SP NONER SP NONE
D I G I T A L
LCR
LSLFE
RS
D I G I T A L
LCR
LSLFE
RSCenter speaker: Not Use
Rear speaker: Not Use
Setting up Delay Time from 00~05ms
Setting up Delay Time from 00~15ms
1
Press the Left/Right (  /  )  button to select
the desired item.
Press the SPK Mode button.

2
•SMALL: When this setting is selected, low frequencies of below 200 Hz are assigned to
the subwoofer only.•USE: Select when using speakers.•NONE: Select this when no speakers are installed.
 
						

							32 31
Speaker Setup 
To set up Speaker Balance
LCR
LSLFE
SRS
D I G I T A L
LCR
LSLFE
SRS
D I G I T A L
LCR
LSLFE
SRS
D I G I T A L
LCR
LSLFE
SRS
D I G I T A L
LCR
LSLFE
SRS
D I G I T A L
1
Use the Left/Right (     /     ) button to make
adjustment.
• Each time the button is pressed the selection switches as shown below.Example: 5.1CH Sound Setup 
OFF, range of –6 ~ 0
OFF, range of –6 ~ 0
range of –6 ~ –00 ~ +6
range of –6 ~ –00 ~ +6
range of –6 ~ –00 ~ +6
Front Speakers: L level, R level
Rear Speakers: L level, R level 
Center Speaker 
Rear Speakers 
Subwoofer Speaker 
Sound Edit
Press the Sound Edit button.

2
The display changes depending on the current audio output
mode (DSP, PRO LOGIC, 3-STEREO, STEREO, etc.).
While in DSP or PRO LOGIC mode, TEST TONE may
operate differently for VCDs or CDs 
Speaker Setting Methods• The test signal will be sent to the Left Front, Center, Right Front,
Right Rear, Left Rear and Subwoofer in that order.
Test Tone
Press the Test Tone button.To End the Language Features Setup 
Test Tone
• Press the Test Tone button again.
L
LS RSC
LFER
Selecting Dolby Pro LogicConverts Dolby Surround encoded 2-channel sound (e.g., program material received by Stereo
VCR could be Dolby Surround encoded 2-channel material that can be decoded into 4-channel
sound using the Dolby Pro Logic mode). Pro Logic mode can also be enjoyed when in DVD
mode or when playing Dolby Digital or PCM material that are Dolby Surround encoded.
Pro Logic
Press the Pro Logic button.
12
Press the Function Selection button to
select the desired function.Press the PRO LOGIC button.• Select from FM, AM, DVD and AUX 1 IN,
AUX 2 IN.
• Each time the Pro Logic button is pressed
CPRO LOGIC
LR
PRO LOGIC
LRLRPRO LOGIC :Left, Center, Right, Subwoofer and
Surround Channel
3-STEREO : Left, Center, Right and Subwoofer
Channel
STEREO : Left, Right and Subwoofer Channel
 
						

							34
Creating Realistic Sound Fields
33You can use the following surround to reproduce a realistic sound field.
• Digital Multichannel Surround —Dolby Digital and DTS Digital Surround
• Dolby Surround
Dolby Digital and DTS Digital SurroundTo enjoy surround effectively,all the speakers need to be connected and activated.
Dolby Digital
Used to reproduce multichannel sound tracks of the software encoded with Dolby Digital (                  ).
Dolby Digitalencoding method (so-called discrete 5.1 channel digital audio format)records and digitally compresses the
left front channel,right front channel,center channel,left rear channel,right rear channel,and LFE channel signals (total 6
channels,but LFE channel is counted as 0.1 channel.Therefore,called 5.1 channel).
Since each channel is completely independent from the other channel signals to avoid interference,you can obtain much
better sound quality with much stereo and surround effects.
In addition,Dolby Digital enables stereo rear sounds,and sets the cutoff frequency of the rear treble at 20 kHz,compared
to 7 kHz for Dolby Pro Logic.These facts enhance the sound movement and being-there feelings much more than Dolby
Pro Logic.
When the system detects Dolby Digital signals,the DOLBY DIGITAL indicator lights up on the display.
DTS Digital SurroundUsed to reproduce multichannel sound tracks of the software encoded with DTS Digital Surround (          ).
DTS Digital Surroundis another discrete 5.1 channel digital audio format available on CD,LD,and DVD software.
Compared to Dolby Digital,audio compression rate is relatively low.
This fact allows DTS Digital Surround format to add breadth and depth to the reproduced sounds.As a result,DTS Digital
Surround features natural,solid and clear sound.
When the system detects DTS Digital Surround signals,the DTS indicator lights up on the display.
Dolby SurroundUsed to reproduce sound tracks of the VCR tapes encoded with Dolby Surround (                            ).
This is only used for the sound sources coming through the AUX IN jacks.
Dolby Pro Logic and Dolby 3 Stereo
Dolby Surroundencoding format records the left front channel, right front channel,center channel,and rear channel
signals (total 4 channels)into 2 channels.
The Dolby Pro Logicdecoder built in this system decodes these 2 channel signals into original 4 channel signals —
matrix-based multichannel reproduction,and allows you to enjoy a realistic stereo sound in your listening room.
When one of Dolby Surround is selected,the PRO LOGIC indicator lights up on the display.Manufactured under license from Dolby Laboratories. “Dolby,”
“Pro Logic,” and the double-D symbol are trademarks of Dolby
Laboratories. Confidential Unpublished Works. ©1992–1997
Dolby Laboratories, Inc. All rights reserved.Manufactured under license from Digital Theater Systems, Inc.
US Pat. No. 5,451,942 and other world-wide patents issued
and pending. “DTS” and “DTS Digital Surround” are
trademarks of Digital Theater Systems, Inc. ©1996 Digital
Theater Systems, Inc. All rights reserved.
DSP Function
To Select a DSP• The DSP mode toggles in the following
order each time the DSP button is pressed:
HALL 
➔ 
THEATER 
➔PAVILION 
➔
DANCE CLUB 
➔LIVE CLUB.
DSP Mode
Press the DSP Mode button.
What is a DSP?
DSP synthetically recreates the sound
field to achieve a more realistic,
powerful sound.
To increase Effect level• The effect level can be set in steps from 1 to 4
EFFECT1 
➔EFFECT2 
➔EFFECT3 
➔
OFF(DEFAULT).  
Each time the button is pressed the selection
moves to the next effect.• The higher the number, the stronger the DSP
surround effect will be.
Effect
Press the Effect button.
What is a Effect?This sets the strength of the DSP
mode.
• DSP mode cannot be selected when a microphone is connected.• When playing a DVD encoded in two or more channels, DSP mode cannot be selected.
 
						

							36 35
When the                   button is pressed, a preset
broadcast station is selected.
Hold in the                 button. Automatic searching
begins, and then stops when a station is tuned in.Press the                    button to tune to the chosen
station. The frequency changes incrementally in either
direction each time the corresponding button is pressed.
Listening to the Radio
Presetting stations
Auto Station 1Auto Station 2 Manual Station 
Press the Tuner(Band)
button.
1
Select a broadcast station.
2
• The selection toggles back
and forth between FM and
AM each time the
Tuner(Band) button is
pressed.
Press the MO/ST button. (only FM)• The selection toggles back and forth between “STEREO” and “MONO”
each time the MO/STbutton is pressed.• In a poor reception areas, select Mono mode for a clear, interference-free
broadcast.To Listen in Mono/Stereo 
AudioMO/ST
• Store the changes while repeating
steps 1 to 4 above.Repeat steps 3 to 4 above.
To store other Channels 
To change the Preset Stations Example: Presetting FM 89.1 in the memory Press the Tuner(Band) button
and select the FM band.Select the MANUAL by
pressing the Stop (     )  button
on the main unit.
1
Use the          and
button to tune into 89.1
2
• The selection toggles back and forth between “FM” and “AM”
each time the Tuner(Band) button is pressed.
3
456
• When using this feature for the 
first time, be sure to store the
station in the preset memory at
FM1 as the unit does not come
preprogrammed with default
presets.
• The preset stations operation is
completed.
Remote 
Control
Unit 
Press the         button to select the PRESET mode. Then
press the                     button to select a station stored in
the preset 
Press the Stop (       )  button to select the MANUAL
mode on the front panel. Then hold in the
button to make the unit begin automaticall searching for
broadcast stations.
Press the Stop (      )   button to select the MANUAL mode front
panel. Press the                         button to tune to the desired
station. The frequency changes incrementally in either direction
each time the corresponding button i s  pressed.
Auto Station 1Auto Station 2 Manual Station 
1
Select a broadcast station.
2
Main
Unit
Press the Function button to
select the desired band (FM,
AM).You can listen to the chosen band (FM, AM broadcast stations) by using either the
automatic tuning or manual tuning operation.
Press the Program button.
Press the Program button. Use the           and
button to select FM2.








You can store up to:15 FM stations
15AM stations          
• FMFrequency Modulation
• AM(MW)Medium Wave
 
						

							38
Troubleshooting 
• Is the disc installed with the label side facing up?• Is the power cord plugged securely into the power outlet?• Turn off the power to the unit by pressing the Power (        ) button
and turn it back on.• Check the region number of the DVD.• DVD discs purchased abroad may not be playable.• This player cannot play CD-ROMs, DVD-ROMs, etc.• Check the rating level of the DVD.• Check whether the disc has any scratch marks or is deformed?
The disc tray does not
open.
Disc does not play.Playback does not start
immediately when the
Play/Pause button is pressed.
• No sound is heard during high-speed playback, slow playback,
and step motion playback modes.• Are the speakers properly connected? Is the speaker Setup
correctly customized?• Is the disc severely damaged?
The disc may be dirty. Wipe off fingerprints or dirt.
No sound is produced.
• 
Was the player moved suddenly from a cold pace to a warm one?
When condensation forms inside the player, remove the disc
and let the player stand for 1 or 2 hours with the power on. 
(You can use the player after the condensation disappears.)
Picture does not appear; sound
is not produced; the disc tray
opens 2-5 seconds later.
• Are the speaker cables loose?• Is there any dirt or debris at the end of the speaker connector?
Sound quality is
irregular.• 
When listening to a CD or radio, sound is output to the front
speakers only (L/R). Select the “PRO LOGIC” option by pressing
the Pro Logic button on the remote control unit to use all six
speakers.• Check whether your DVD disc is 5.1 CH compatible.
Sound can be heard only
from a few speakers and
not all six.
• 
Does the disc being played show the “Dolby Digital 5.1CH” mark ?
5.1-channel sound is reproduced only if the disc is recorded with
5.1 channel sound.• Is the DVD player connected to the proper speakers?
Dolby Digital 5.1 Channel
Surround Sound is not
being reproduced.
Problem
Check
Sleep Function
37
To set up Sleep• Each time the button is pressed the selection
toggles as follows: SLEEP 10
➔SLEEP 20
➔SLEEP 30 
➔ 
SLEEP 60 
➔ 
SLEEP 90 
➔ 
SLEEP 120 
➔ 
SLEEP 150 
➔ 
OFF.
• The remaining time for the selected Sleep time is displayed.• Pressing the button once again changes the Sleep time from the
last setting.
Sleep
Press the Sleep button.
What is the 
Sleep function?
You can set the delay time so that
the unit powers off automatically
after a preset period of time.
To Review Sleep Setting