Samsung Ht C6950w User Manual

							
0 English
English 1

02
Connections

 NOTE
 
If you place a speaker near your TV set, screen colour may be distorted because of the magnetic field generated by the speaker. If this occurs, place the speaker away from your TV set.Place the wireless receiver module at the rear of the listening position. If the wireless receiver module is too close to the product, some sound interruption may be heard due to interference.If you use a device such as a microwave oven, wireless LAN Card or any other device that uses the same frequency (2.4/5.8GHz) near the product, some sound interruption may be heard due to interference.The transmission distance from the product to the wireless receiver module is about 10m, but may vary depending on your operating environment. If a steel-concrete wall or metallic wall is between the product and the wireless receiver module, the system may not operate at all, because the radio wave cannot penetrate metal.If the product doesn't make wireless connection, the system needs ID Setting between the product and wireless receiver module. With the product turned off, press the remote control's number buttons "0""1""3""5" and turn on the product. With the wireless receiver module turned on, press "ID SET" button on the back of the wireless receiver module for 5 seconds.
✎





CAUTION
Do not let children play with or near the speakers. They could get hurt if a speaker falls.
When connecting the speaker wires to the speakers, make sure that the polarity (+/–) is correct.
   Keep the subwoofer speaker out of reach of children so as to prevent children from inserting their 
hands or alien substances into the duct (hole) of the subwoofer speaker.
   Do not hang the subwoofer on the wall through the duct (hole).
Do not insert any other card except the TX card dedicated to the product.  If a different TX card is used, the product may be damaged or the card may not be removed easily.Do not insert the TX card upside down or in the reverse direction.
   Insert the TX card when the product is turned off. Inserting the card when it is turned on may 
cause a problem.
  The wireless receiving antenna is built into the wireless receiver module. Keep it away from water 
and moisture.For optimal listening performance, make sure that the area around the wireless receiver module location is clear of any obstructions.If no sound is heard from the wireless surround speakers, switch the mode to DVD 5.1 channel or Dolby Pro Logic II.In 2-CH mode, no sound will be heard from the wireless surround speakers.
!







 
						

							
 English

Connections

English 

Connecting external Devices/your tv via HDmI
HDMI is a standard digital interface for connection to such devices as a TV, projector, DVD player, Blu-ray 
player, set top box and more.
HDMI removes any loss of signal from analogue conversion, enabling you to enjoy video and audio sound 
quality as it was originally created in the digital source.
HDMI OUT : Connecting to a TV with an HDMI Cable (BEST QUALITY)
Connect an HDMI cable from the HDMI OUT jack on the back of the product to the HDMI IN jack on 
your TV.
 NOTE
Certain HDMI output resolutions may not work, depending on your TV.
If an HDMI cable is connected or removed during playback of a CD-DA, MP3 or JPEG fi le, the product will 
stop playing.
After making the video connection, set the Video input source on your TV to match the corresponding Video 
output (HDMI, Component or Composite) on your product.
See your TV owner's manual for more information on how to select the TV's Video Input source.
If you have set the product's remote control to operate your TV, press the SOURCE button on the remote 
control and select HDMI as the external source of the TV.
You must have an HDMI connection to enjoy videos with 3D technology.
A long HDMI cable may cause a screen noise. If this is the case, set Deep Color to Off in the menu.
✎






LANFM ANTWIRELESS
OPTICAL
DIGITALAUDIO IN
VIDEO OUT
COMPONENT OUT
SPEAKER IMPEDANCE : 3 
HDMI INHDMI OUT
WIRELESS LAN
LANFM ANTWIRELESS
OPTICAL
DIGITALAUDIO IN
VIDEO OUT
COMPONENT OUT
SPEAKER IMPEDANCE : 3 
HDMI INHDMI OUT
WIRELESS LAN
DVD or Blu-ray PlayerSAT(Satellite/Set top box)
HDMI IN
HDMI OUT
 
						

							
 English
English 

02
Connections

HDMI IN : Connecting to an External Component with an HDMI Cable
Connect an HDMI cable from the HDMI IN jack on the back of the product to the HDMI OUT jack 
on your digital devices.
Press the FUNCTION button to select HDMI. IN1 or HDMI. IN2 input. 
The mode switches as follows : BD/DVD ; D. IN ; AUX ; HDMI. IN1 ; HDMI. IN2 ; FM
HDMI Auto Detection Function
The product's video output will automatically change to HDMI mode when connecting an HDMI cable 
before power is on. For possible HDMI resolutions, see page 32.
This function is not available if the HDMI cable does not support CEC.
HDMI connection description
- HDMI outputs only a pure digital signal to the TV.
-   If your TV does not support HDCP, random noise appears on the screen.
What is the HDCP? 
HDCP (High-band width Digital Content Protection) is a system for protecting BD/DVD content outputted via 
HDMI from being copied. It provides a secure digital link between a video source (PC, DVD. etc) and a display 
device (TV, projector. etc). Content is encrypted at the source device to prevent unauthorized copies from being 
made.
CAUTION
The Anynet+ function is supported only when an HDMI Cable is connected to the HDMI OUT of the 
product.
1.
2.
•
•
•
!

Connecting the fm antenna
Connect the FM antenna supplied to the 
FM 75Ω COAXIAL Jack.
Slowly move the antenna wire around until 
you find a location where reception is good, 
then fasten it to a wall or other rigid surface.
NOTE
This product does not receive AM 
broadcasts. 
1.
2.
✎

FM ANT
WIRELESSOPTICAL
DIGIRALAODIO IN
FM Antenna (supplied)
 
						

							
 English

Connections

English 

METHOD 1 : Component Video  (BETTER QUALITY)
If your television is equipped with Component Video inputs, connect a Component video cable (not supplied) from the Component Video Output (Pr, Pb and Y) Jacks on the back of the product to the Component Video Input Jacks on your TV.
 NOTE
You can select from a variety of resolution settings such as 1080i, 720p, 576p(480p) and 576i(480i), depending on the disc type. (See page 32)The actual resolution may differ from the setting in the Setup menu if both Component and HDMI cables are connected. The resolution may also be different depending on the disc. (See page 32)After making the video connection, set the Video input source on your TV to match the corresponding Video output (HDMI, Component or Composite) on your product.See your TV owner's manual for more information on how to select the TV's Video Input source.If you have set the product's remote control to operate your TV, press the TV SOURCE button on the remote control and select COMPONENT as the external source of the TV.In DVD playback, if both HDMI and Component jacks are connected and you select the Component 1080p, 1080i, 720p or 576p(480p) mode, the Display Setup menu will show the output resolution as 1080p, 1080i, 720p or 576p(480p) in the menu. The resolution is actually 576i(480i).
METHOD 2 : Composite Video (GOOD QUALITY) 
Connect the supplied Video cable from the VIDEO OUT jack on the back of the product to the VIDEO IN jack on your TV.
NOTE
The VIDEO source is always output in 576i(480i) resolution regardless of the resolution set in the Setup menu. (See page 32)After making the video connection, set the Video input source on your TV to match the corresponding Video output (HDMI, Component or Composite) on your product.See your TV owner's manual for more information on how to select the TV's Video Input source.If you have set the product's remote control to operate your TV, press the  TV SOURCE button on the remote control and select VIDEO as the external source of the TV.
CAUTION
Do not connect the unit through a VCR. Video signals fed through VCRs may be affected by copyright protection systems and the picture will be distorted on the television.
✎





✎



!

Connecting the video out to your tv
LAN
HDMI OUT
VIDEO OUT
COMPONENT OUT
WIRELESS LAN
LAN
VIDEO OUT
COMPONENT OUT
WIRELESS LAN
Red
Yellow
METHOD 1
BlueGreen
METHOD 2
 
						

							
 English
English 

02
Connections

Connecting audio from external Components
OPTICAL : Connecting an External Digital Component
Digital signal components such as a Cable Box/Satellite receiver (Set-Top Box).
Connect the Digital Input (OPTICAL) on the product to the Digital Output of the external digital 
component.
 Press the FUNCTION button to select D.IN input.
The mode switches as follows : BD/DVD ; D. IN ; AUX ; HDMI. IN1 ; HDMI. IN2 ; FM
NOTE
To see video from your Cable Box/Satellite receiver, you must connect it's video output to a TV.
This system supports Digital sampling frequencies of 32 kHz of higher from external digital components.
This system supports only DTS and Dolby Digital audio, MPEG audio which is bitstream cannot be supported.
AUX : Connecting an External Analogue Component
Analogue signal components such as a VCR.
Connect AUX IN (Audio) on the product to the Audio Out of the external analogue component.
 Be sure to match connector colours.
 Press the FUNCTION button to select AUX input. 
The mode switches as follows : BD/DVD ; D. IN ; AUX ; HDMI. IN1 ; HDMI. IN2 ; FM
NOTE
  You can connect the Video Output jack of your VCR to the TV, and connect the Audio Output jacks of 
the VCR to this product.
1.
2.
•
✎



1.
•
2.
•
✎

LAN
HDMI INHDMI OUT
VIDEO OUT
COMPONENT OUT
OPTICAL
DIGITALAUDIO IN
WIRELESS LAN
LAN
HDMI INHDMI OUT
VIDEO OUT
COMPONENT OUT
DIGITALAUDIO IN
WIRELESS LAN
Optical Cable
(not supplied)Audio Cable 
(not supplied)
If the external analogue 
component has only one 
Audio Out, connect either 
left or right.Set-Top BoxVCR
WhiteRed
OPTICALAUX
 
						

							
 English

Connections

English 

Connecting to the network
By connecting to a network, you can access the BD-LIVE and Software upgrades from Samsung’s
update server. We recommend using an AP (Access Point) or IP router for the connection.
For more information on router connection, refer to the user manual of the router or contact the router
manufacturer for technical assistance.
Cable Network
Using the Direct LAN Cable (UTP cable), connect the LAN terminal of the product to the LAN 
terminal of your modem.
Set the network options. (See page 39)
NOTE
Internet access to Samsung’s software update server may not be allowed, depending on the router you use or the 
ISP’s policy. For more information, contact your ISP (Internet Service Provider).
For DSL users, please use a router to make a network connection.
For the AllShare function, a PC must be connected in the network as shown in the fi gure.
1.
2.
✎



HDMI INHDMI OUT
VIDEO OUT
COMPONENT OUTYLAN
WIRELESS LAN
HDMI INHDMI OUT
VIDEO OUT
COMPONENT OUTYY
WIRELESS LAN
Router
Broadband modem
Broadbandservice
Or
Broadband modem(with integrated router)
Broadbandservice
Networking with PC forAllShare function(See pages 56~57)
 
						

							
 English
English 

02
Connections

HDMI INHDMI OUT
VIDEO OUT
COMPONENT OUTYLAN
WIRELESS LAN

Wireless Network
You can connect to the network with a Wireless IP sharer.
A wireless AP/IP router is required to make a wireless network connection. Connect the wireless
LAN adapter to the Wireless LAN Adapter on the rear panel of the product. 
- This unit is compatible with the supplied Wireless LAN Adapter.
-  You can also use the wireless network by connecting the Wireless LAN Adapter Gender to the 
Wireless LAN Adapter.
Set the network options. (See page 39)
NOTE
You must use a wireless IP sharer that supports IEEE 802.11 a/b/g/n. (n is recommended for stable 
operation of the wireless network.)
Wireless LAN, in its nature, may cause interference, depending on the use condition (AP performance, 
distance, obstacle, interference by other radio devices, etc).
Set the wireless IP sharer to Infrastructure mode. Ad-hoc mode is not supported.
When applying the security key for the AP (wireless IP sharer), only the following is supported.
Authentication Mode : WEP, WPAPSK, WPA2PSK
Encryption Type : WEP, AES
For the AllShare function, a PC must be connected in the network as shown in the fi gure.
1.
2.
✎




1)
2)

COMPONENT OUT
VIDEO OUT
LAN
AUX
HDMI OUT
WIRELESS LAN
COMPONENT OUT
VIDEO OUT
LAN
AUX
HDMI OUT
Wireless IP sharer
Networking with PC for
AllShare function
(See pages 56~57)
PC
Broadband
service
Wireless LAN Adapter
OR
 
						

							
 English

Setup

English 

Before Starting (Initial Settings)
Turn on your TV after connecting the product.(When the product is connected to TV for the fi rst time,  product  will turn on automatically and the 
Initial Settings screen will be displayed.)
 > Move s Select
Initial Settings I On-Screen Language
Select a language for the on-screen displays.
EnglishFrançaisDeutschEspañolItalianoNederlands
Press the ▲▼ buttons to select the desired language, then press the ENTER button.
Press the ENTER button to select Start button.
      a Previous " Select
Initial Settings
TV Aspect, Musical Auto Calibration and Network will be set.Each setting may be changed later under "Settings"
Start
Press the ▲▼ buttons to select desired TV Aspect ratio, then press the ENTER button. (See page 31)Musical Auto Calibration screen will be displayed.
Plug the ASC microphone into the ASC IN jack on the product. (See page 35)
Press the ENTER button to select Start button.
       d Skip
Initial Settings I Musical Auto Calibration
Preparing...
Setting the Musical Auto Calibration function takes about 3 minutes.
1.
2.
3.
4.
5.
6.
Press the ◀▶ buttons to the select the 
desired Network Settings: Wired, Wireless or 
PBC (WPS), then press the ENTER button. 
(See pages 39~42)
The Network Test will start and Initial Settings 
will be completed.
a Previous d Skip < Move " Select
Initial Settings I Network
Network Setting is needed to use various Internet services.Choose the primary method for connecting to network.
Wired : Set the network by using Ethernet cable.Please make sure that Ethernet cable is connected.
WiredWirelessPBC (WPS)
Press the OK button. 
The home menu will be displayed. (For more 
information about home menu, please see 
page 29)
Home Menu
No Disc a Change Device d View Devices " Enter
Videos
 NOTE
When the product is connected to TV for the 
fi rst time, product will turn on automatically.
Do not confuse because this is not 
malfunction.
The home menu will not be displayed if you do 
not confi gure the initial settings.
If you press the BLUE(D) button during the 
Musical Auto Calibration/Network setup, you 
can access the home menu even if the 
network setup is not completed yet.
When you return to home menu, the full 
screen mode will be cancelled automatically.
7.
8.
•
✎




 
						

							
 English
English 

03
Setup

If you want to display Initial Settings screen 
again in order to make changes, press the 
STOP (@) button on the front panel of the 
product for more than 5 seconds with no disc 
inserted.
Use the HDMI cable to connect the product to 
an Anynet+(HDMI-CEC)-compliant Samsung TV.
If the TV uses a language supported by the 
product, that language will be set to a 
preferred language automatically.
However, the Anynet+(HDMI-CEC) feature 
should be set to On in both TV and the 
product.If the product is left in the stop mode for more than 5 minutes without being operated, a screen saver will appear on your TV. If the product is left in the screen saver mode for more than 25 minutes, the power will automatically turn off except during playback of a CD-DA (Automatic Power-Off Function).
Setting the menu
FUNCTIONTV SOURCEPOWER
BD RECEIVER/TVSLEEP
DISC MENUMENUTITLE MENU
MUTE
SFE MODE
DSP
VOLTUNING/CH
TOOLS
RETURNEXIT
INFO
ABCD
TUNER MEMORY
INIERNET 
MO/ST
REPEATFULL SCREEN
123
456
78
0
9
POPUP
@
DISC MENUTITLE MENU
TOOLSINFO
TUNER 
POPUP1
24
3
1MENU Button : Press this to move to the home menu.
2RETURN Button : Return to the previous menu.
3
ENTER / DIRECTION Button:Press the arrow buttons to move the cursor and select an item.Press the ENTER button to launch the selected item or confi rm the setting.
4EXIT Button : Press this to exit the menu.



Press the POWER button.
The Home Menu will appear.
Home Menu
No Disc a Change Device d View Devices " Enter
Videos
14
5
2
3
1Selects the Videos.
2Selects the Music.
3Selects the Photos.
4Selects the Settings.
5Displays buttons available.
Press the ◀▶ buttons to select Settings, 
then press the ENTER button.
Press the ▲▼ buttons to select the desired 
submenu, then press the ENTER button.
Press the ▲▼ buttons to select the desired 
item, then press the ENTER button.
Press the EXIT button to exit the menu.
NOTE 
The access step may differ depending on the 
selected menu.
The OSD (On Screen Display) may change in 
this product after upgrading the software 
version.
1.
•
2.
3.
4.
5.
✎


 
						

							
0 English

Setup

English 1

Display
You can confi gure various display options such as the TV Aspect, Resolution, 3D, etc.
3D
Select whether to play a Blu-ray Disc with 3D contents in 3D Mode.
DisplayAudioSystemNetworkLanguageSecurityGeneralSupport
Settings 
3D
Still Mode  : Auto
3D Mode : AutoTV Screen Size :      55    inch
 > Move s Select r Return
3D
3D Mode
Auto : The 3D Blu-ray Disc is played in 3D 
mode if your product detects a TV which 
supports it. It is played in 2D mode if your 
product detects a TV which cannot support it.
3D : The 3D Blu-ray Disc is played in 3D mode 
at all times. If a TV cannot support 3D Blu-ray 
discs, the TV's screen can be black.
2D : The 3D Blu-ray Disc is played in 2D mode 
at all times. Choose this to view a picture 
without 3D effect or when a TV cannot support 
3D Blu-ray discs.
NOTE
If you press the STOP(@) button once during 
the 3D disc playback, 3D mode option will not 
be deactivated.
To activate 3D mode option during the 3D disc 
playback, press the STOP(@) button twice.
Depending on the content and its play position, 
vertical black bars could be seen on left or right 
or both sides.
•
•
•
✎


TV Screen Size
Lets you enter the actual screen size of your 
TV so that the product can adjust the image 
according to the screen size and display an 
optimal 3D image. (The maximum allowed 
screen size is 116 inches for this product.)
CAUTION
If you want to enjoy a 3D content, connect a 3D device (3D compliant AV receiver or TV) to the product and wear a 3D glass before playing the 3D content.
While watching the 3D video, all analog component and composite signals will be blocked automatically.
All 3D signals are output only using the HDMI cable and through the HDMI OUT port.
As the video resolution in 3D play mode is fi xed according to the resolution of the original 3D video, you can not change the resolution to your preference.
Some functions such as BD Wise, or setting the screen size or resolution may not operate properly in 3D play mode.
You must use a high-speed HDMI cable for a proper output of the 3D signal.
Stay at least three times of the length of the screen distant from the TV.-  It is recommended to place the 3D video screen forward at eye level.
If the product is connected to some 3D devices, the 3D effect may not function properly.
You can not use this product for switching a 2D content to 3D.
!