Samsung Ht Bd8200 User Manual

							
21
ENG
●  CONNECTIONS
INSTALLING THE WALL MOUNT
1.  Disconnect the cradle stand from the unit.
2.  Peel off the fi lm from the double-sided adhesive sheet 
for the wall mount and attach it on a clean wall.
3. 
Secure the wall mount bracket using 6 screws (not 
supplied) while aligning holes marked on the sheet.
4.  Attach the back unit bracket(bracket set mount) with 
the Home Theater unit by fastening provided 4 screws.
5. 
Fully insert the back bracket’s clasp into 
the wall mount bracket’s receptacle and 
fi x it by fully sliding to the right. Installation completed.
Do not hang onto the installed unit and avoid any impact to the unit.
Secure the unit fi rmly to the wall so that it does not fall off. If the unit falls off, it\
 may result in an 
injury or damage to the product.
When the unit is installed on a wall, please make sure that a child does\
 not pull any of 
connecting cables, as it may cause it to fall.
•
M▪
▪
▪
Do not install on a place other than a vertical wall.
When installating, avoid locations with high temperature or humidity, or\
 a wall that cannot 
sustain the weight of the set.
Check the strength of the wall. If the strength of the wall is insuffi\
 cient for the product 
installation, make sure to reinforce the wall before the installation.
Check the material of the wall. If the wall is made of plaster board, ma\
rble, or iron board, 
purchase and use the appropriate fi xing screws.
Cables connecting to external devices are to be connected to the unit be\
fore installing.
Be sure to turn off the unit before installation. Otherwise, it may caus\
e electric shock.
Do not turn the assembled cradle stand and main unit upside down, as the\
 main unit may fall 
from the stand and cause product damage or personal injury.






INSTALLING THE CRADLE STAND
You can use the cradle stand to install this unit on a shelf. Make sure \
you place the unit on a fl at surface.
Connecting
Face the  FRONT mark on the stand forward and slide the 
stand into the bottom of the unit until you hear a click.
H T-B D 8200_X AA_0724-1 .in dd   2 1HT-BD8200_XAA_0724-1.indd   212009-0 7-2 4     1 1:0 9:5 72009-07-24    11:09:57
 
						

							
22
Connections
CONNECTING THE VIDEO OUT TO YOUR TV
Choose one of the two methods for connecting to a TV.
  METHOD 1 : HDMI (BEST)
Connect the HDMI cable (not supplied) from the HDMI OUT jack on the ba\
ck of the Blu-ray Home Theater 
to the HDMI IN jack on your TV.
Depending on your TV, certain HDMI output resolutions may not work.
If an HDMI cable is connected from the player to a TV, the Blu-ray Home \
Theater’s output is set to 
HDMI automatically within 10 seconds.
When you connect the player to the TV using the HDMI cable for the fi rst time or to a new TV, the 
HDMI output resolution will automatically be set to the highest provided\
 by the TV.
If you connect a Samsung TV to the Blu-ray Home Theater using an HDMI ca\
ble, the player can 
be easily operated using the TV remote control. (This is only available\
 with Samsung TVs that 
support the Anynet+ feature.) (See page 44)
After making the video connection, set the Video input source on your TV\
 to match the
corresponding Video output (HDMI) on your Blu-ray Home Theater.
See your TV owners manual for more information on how to select the TV\
s Video Input source.M




METHOD2
(supplied)
METHOD1
H
T-B D 8200_X AA_0724-1 .in dd   2 2HT-BD8200_XAA_0724-1.indd   222009-0 7-2 4     1 1:0 9:5 82009-07-24    11:09:58
 
						

							
23
ENG
●  CONNECTIONS
HDMI Auto Detection Function
The players video output will automatically change to HDMI mode when co\
nnecting an HDMI cable 
while power is on. For possible HDMI resolutions, see page 41.
HDMI (High Defi  nition Multimedia Interface)
HDMI is an interface that enables the digital transmission of video and \
audio data with just a single connector.Using HDMI, the Blu-ray Home Theater transmits a digital video and audio\
 signal and displays a vivid picture on a 
TV having an HDMI input jack.
HDMI connection description
HDMI connector - Supports video and digital audio data.
- HDMI outputs only a pure digital signal to the TV.
- 
  If your TV does not support HDCP (High-bandwidth Digital Content Protec\
tion), random noise appears on the screen.
Why does Samsung use HDMI?
Analog TVs require an analog video/audio signal. However, when playing a\
 BD/DVD, the data 
transmitted to a TV is digital. Therefore either a digital-to-analog con\
verter (in the Blu-ray Home Theater) or an 
analog-to-digital converter (in the TV) is required. During this conve\
rsion, the picture quality is degraded due to 
noise and signal loss. HDMI technology is superior because it requires n\
o D/A conversion and is a pure digital 
signal from the player to your TV.
What is the HDCP?
HDCP (High-band width Digital Content Protection) is a system for prot\
ecting BD/DVD content outputted via HDMI 
from being copied. It provides a secure digital link between a video sou\
rce (PC, DVD. etc) and a display device (TV, 
projector. etc). Content is encrypted at the source device to prevent u\
nauthorized copies from being made.
What is Anynet+?
Anynet+ is a convenient function that offers linked operation of this un\
it through Samsung TVs with the Anynet+ feature.
-  If your Samsung TV has an  logo, then it supports the Anynet+ function.
-        If you turn on the player and insert a disc, the player will start playi\
ng the disc, and the TV will turn on 
automatically and switch to HDMI mode.
-   If you turn on the player and press the  PLAY button with a disc already inserted, the TV will immediately turn on 
and switch to HDMI mode.
What is BD Wise?
BD Wise is Samsung's latest inter-connectivity feature.
-   When you connect Samsung products with BD-Wise to each other via HDMI, t\
he optimum resolution will be set 
automatically. 
METHOD 2 : Composite Video (GOOD)
Connect the supplied Video cable from the VIDEO OUT jack on the back of \
the Blu-ray Home Theater 
to the VIDEO IN jack on your TV.
The VIDEO source is always output in 480i resolution regardless of the r\
esolution set in the SETUP 
menu. (See page 42)
After making the video connection, set the Video input source on your TV\
 to match the 
corresponding Video output (Composite) on your Blu-ray Home Theater.
See your TV owners manual for more information on how to select the TV\
s Video Input source.
Do not connect the unit through a VCR. Video signals fed through VCRs ma\
y be affected by 
copyright protection systems and the picture will be distorted on the te\
levision.
•
•
•
•
•
•
M


H T-B D 8200_X AA_0724-1 .in dd   2 3HT-BD8200_XAA_0724-1.indd   232009-0 7-2 4     1 1:0 9:5 92009-07-24    11:09:59
 
						

							
24
Connections
CONNECTING AN iPod
You can enjoy music and video fi les from an iPod through the main unit. For iPod operation with this Blu\
-ray home 
theater, see pages 25 and 78 ~ 80.     Connect the iPod Dock to the iPod Jack on the rear side of the main unit\
.
  Place the iPod in the dock.  “iPod Connected” message appears on the TV screen.
 You must have the VIDEO output connected to your TV to view iPod video (\
See page 25).
As the cable ports are close together, be sure to remove the USB memory \
drive before 
disconnecting the ipod docking cable.
Adjust the volume to a moderate level before you connect your iPod and B\
lu-ray home theater.
When the unit is powered on and you connect an iPod, the unit will charg\
e your iPods battery.
Make sure to connect the dock connector so that the label “ SAMSUNG” faces backword.
“Made for iPod” means that an electronic accessory has been design\
ed to connect 
specifi cally to iPod and has been certifi ed by the developer to meet Apple performance 
standards.
1.
2.
•
M





(supplied)
HT-B D 8200_X AA_0724-1 .in dd   2 4HT-BD8200_XAA_0724-1.indd   242009-0 7-2 4     1 1:0 9:5 92009-07-24    11:09:59
 
						

							
25
ENG
●  CONNECTIONS
iPod models that can be used with the HT-BD8200
“Made for iPod” means that an electronic accessory has been design\
ed to connect specifically to the 
iPod and has been certified by the developer to meet Apple performance\
 standards.
“Works with iPhone” means that an electronic accessory has been de\
signed to connect 
specifically to an iPhone and has been certified by the developer to\
 meet Apple performance 
standards.
Apple is not responsible for the operation of this device or its complia\
nce with safety and 
regulatory standards.
iPod is a trademark of Apple Inc., registered in the U.S. and other coun\
tries. iPhone is a 
trademark of Apple Inc.
M


H T-B D 8200_X AA_0724-1 .in dd   2 5HT-BD8200_XAA_0724-1.indd   252009-0 7-2 4     1 1:1 0:0 02009-07-24    11:10:00
 
						

							
26
Connections
CONNECTING AUDIO FROM EXTERNAL COMPONENTS
OPTICAL : Connecting an External Digital Component
Digital signal components such as a Cable Box/Satellite receiver (Set-T\
op Box).      Connect the Digital Input (OPTICAL) on the main unit to the Digital Ou\
tput of the external digital 
component.
  Press the  FUNCTION  button on the main unit to select  DIGITAL input.
The mode switches as follows :  BD/DVD ➞ DIGITAL  ➞  AUX  ➞  TUNER .
To see video from your Cable Box/Satellite receiver, you must connect it\
s video output 
to a TV.
This  s ys te m  s u p ports  D ig it a l  s a m plin g  fr e q uen cie s o f  3 2 k H z o f  h ig her fr o m  e xte rn al  d ig it a l This system supports Digital sampling frequencies of 32 kHz of higher fr\
om external digital 
c o m ponen ts .components.
T his  s ys te m  s u p ports  o nly  D TS  a n d  D olb y D ig it a l  a u d io , M PEG  a u d io  w hic h  is  b it s tr e am  This system supports only DTS and Dolby Digital audio, MPEG audio which \
is bitstream 
can no t b e s u p porte d .cannot be supported.
1.
2.
•
M


Optical Cable
 (not supplied)
HT-B D 8200_X AA_0724-1 .in dd   2 6HT-BD8200_XAA_0724-1.indd   262009-0 7-2 4     1 1:1 0:0 02009-07-24    11:10:00
 
						

							
27
ENG
●  CONNECTIONS
AUX : Connecting an External Analog Component
Analog signal components such as a VCR.
      Connect AUX IN (Audio) on the main unit to the Audio Out of the extern\
al analog component.
 
Be sure to match connector colors.
 
Press the  AUX button on the remote control to select  AUX input. 
You can also use the  FUNCTION button on the main unit.
The mode switches as follows :  BD/DVD ➞ DIGITAL  ➞  AUX  ➞  TUNER .
  
You can connect the Video Output jack of your VCR to the TV, and connect\
 the Audio 
Output jacks of the VCR to this product.
1.
•
2. •M
Audio Cable (not supplied)
If the external analog component has 
only one Audio Out, connect either left 
or right.
H T-B D 8200_X AA_0724-1 .in dd   2 7HT-BD8200_XAA_0724-1.indd   272009-0 7-2 4     1 1:1 0:0 12009-07-24    11:10:01
 
						

							
28
Connections
CONNECTING TO THE NETWORK
To access network service or upgrade the current fi rmware, you must make one of the following connections.
By connecting to a network, you can access the BD-LIVE, Blockbuster, Net\
fl ix, Pandora, YouTube services, PC
streaming and Software upgrades from Samsung’s update server. We reco\
mmend you use an AP or router for the network.
If you don’t have one, you'll need two network providing services to \
use the PC streaming function.
Case 1 : Connecting a Direct LAN Cable to your Modem
Using a Direct LAN Cable (UTP cable, not supplied), connect the LAN te\
rminal of the Blu-ray Disc  
Player to the LAN terminal of your modem.
To use the PC streaming  function (see pages 81~82), please make a network between your PC 
and router.
Internet access to Samsung’s update server may not be allowed, depend\
ing on the router you 
use or the ISP’s policy.
For more information, contact your ISP (Internet Service Provider).
For DSL users, please use a router to make a network connection.
1.
M


To LAN port
Broadbandservice
Broadband modem
(with integrated router) Router Broadband modem
To LAN port
To LAN port Broadband
service
Or
PC connection to Router 
for PC streaming
Connecting using a router 
(e.g. DSL)
HT-B D 8200_X AA_0724-1 .in dd   2 8HT-BD8200_XAA_0724-1.indd   282009-0 7-2 4     1 1:1 0:0 22009-07-24    11:10:02
 
						

							
29
ENG
●  CONNECTIONS
Case 2 : Connecting to a Wireless IP sharer
You can connect to network with a Wireless IP sharer. See page 50 for Wi\
reless Network Setup.
This unit is compatible with the Samsung Wireless LAN Adapter only.
(Model name: WIS09ABGN). 
You must use a wireless IP sharer that supports IEEE 802.11 a/b/g/n. (n\
 is recommended 
for stable operation of the wireless network.)
Wireless LAN, in its nature, may cause interference, depending on the us\
e condition 
(AP performance, distance, obstacle, interference by other radio device\
s, etc).
Set the wireless IP sharer to Infrastructure mode. Ad-hoc mode is not su\
pported.
When applying the security key for the AP (wireless IP sharer), only t\
he following is 
supported.
Authentication Mode : WEP, WPAPSK, WPA2PSK
Encryption Type : WEP, TKIP, AES
Connect the Wireless Lan Adapter to only the Wireless Lan Jack on the ba\
ck of  the main 
unit.M




1)
2)

Modem Port
Wireless IP sharer Modem Cable
Wireless LAN Adapter
OR
HT-B D 8200_X AA_0724-1 .in dd   2 9HT-BD8200_XAA_0724-1.indd   292009-0 7-2 4     1 1:1 0:0 42009-07-24    11:10:04
 
						

							
30
Connections
CONNECTING THE FM ANTENNA
      Connect the FM antenna supplied to the FM 75 Ω COAXIAL Jack.
     Slowly move the antenna wire around until you fi nd a location where reception is good, then fasten it 
to a wall or other rigid surface.
  This unit does not receive AM broadcasts.
COOLING FAN
The cooling fan supplies cool air to the unit to prevent overheating.
Please observe the following cautions for your safety.
Make sure the unit is well-ventilated. If the unit has poor ventilation,\
 the temperature inside the unit may rise 
and may damage it.
Do not obstruct the cooling fan or ventilation holes. (If the cooling f\
an or ventilation holes are covered with a 
newspaper or cloth, heat may build up inside the unit and fi re may result.)
ATTACHING THE TOROIDAL FERRITE CORE TO THE POWER CORD 
OF THE MAIN UNIT
If you attach a Toroidal ferrite core to the power cord of the man unit,\
 it will prevent help to prevent RF
interference from radio signals.
      Pull the fi xing tab of the Toroidal ferrite core to open it.
   Make a loop twice in the main unit power cord.
   
Attach the Toroidal ferrite core to the main unit power cord as the fi\
 gure shows and press it until it clicks.
1.
2.
M
•
•
1.
2.
3.
FM Antenna (supplied)
H T-B D 8200_X AA_0724-1 .in dd   3 0HT-BD8200_XAA_0724-1.indd   302009-0 7-2 4     1 1:1 0:0 52009-07-24    11:10:05