Samsung HL-S6767W Dlp Tv Owners Instructions

English - 11
Right Side Buttons
The buttons on the right side panel control your TV’s basic features, including the on-screen menu system.
To use the more advanced features, you must use the remote control.
The product color and shape may vary depending on the model.
Press to switch between viewing TV programs and signals from connected components.
Press to see the on-screen menu.
Press to raise or lower the volume and to select items when using the on-screen menu.
Press to change channels and move...

Your New Wide TV
English - 12
Rear Panel Jacks
ŒVIDEO/AUDIO INPUT jacks Connect video/audio signals from external sources, such as VCR
or DVD players. (Refer to pages 19, 22, and 24)
´
S-VIDEO INPUT jacksConnects an S-Video signal from an S-VHS VCR or DVD player. 
(Refer to pages 19, and 24)
ˇ
VIDEO/AUDIO OUTPUT jacks  Sends video/audio signals from the TV to an external source,
such as a VCR. These jacks are available only in TV, Video and 
S-Video modes. (Refer to page 24)
¨
COMPONENT IN 1, 2 jacks (Y,...

English - 13
Remote Control
You can use your remote control within a distance of 23 feet and an angle of 30 degrees from the left
and right sides of the TV’s remote control receiver. You can also use your remote control to operate your
VCR, Cable box, DVD player and Set-top box. See pages 34~40 for details. 
1. POWERTurns the TV on and off.
2. Channel Number Press to directly tune to a particular channel.
3.-Press to select additional channels (digital
and analog) being broadcast by the same
station. For...

Your New Wide TV
English - 14
Installing Batteries in the Remote Control
With normal use, the batteries in the remote control should last about a year. If you notice a performance
degradation while using the remote, the batteries may need to be replaced. Make sure you replace both
batteries and do not mix old and new batteries in the remote control. If you won’t be using the remote
control for a long time, remove the batteries and store them in a cool, dry place.
1
Lift the cover at the back of the...

Connections
BP68-00588G-00Eng(002~015)  4/22/06  2:01 PM  Page 15 

Connections
English - 16
Connecting VHF and UHF Antennas
If you do not have a cable system, you will need to connect an antenna to your TV.  
Antennas with 75-ohm Round Leads
If your antenna looks like this: it has 75-ohm round leads.
1
Plug the antenna lead into
the ANT 2 IN (AIR) on the 
rear panel of your TV.
BP68-00588G-00Eng(016~027)  4/22/06  4:02 PM  Page 16 

English - 17
Connecting Cable TV
You can connect different cable systems to your TV, including cable without a Cable box, 
and cable with a Cable box that descrambles some or all channels.
Cable without a Cable Box
1
Plug the incoming cable into
the ANT 1 IN (CABLE) on the
rear panel of your TV.
Cable with a Cable Box that Descrambles All Channels
1
Find the cable connected to
the ANTENNA OUT 
terminal on your Cable box. 
This terminal might be 
labeled “ANT OUT”, “VHF 
OUT” or simply “OUT”.
2
Connect...

Connections
English - 18
Cable with a Cable Box that Descrambles Some (But Not All) Channels
To complete this connection you will need a two-way splitter, an RF (A/B) switch, and four coaxial
cables (which you can buy from your Samsung dealer or any electronics store).
1
Find and disconnect the
cable that is connected to 
the ANTENNA IN terminal 
of your Splitter. 
This terminal might be 
labeled “ANT IN”, “VHF IN”
or simply, “IN”. Connect this 
cable to a two-way splitter.
2
Connect a coaxial cable...

English - 19
Connecting a VCR
Connecting a VCR to the Video or S-Video/Audio jack
1
Connect a video cable
between the VIDEO IN (1   
or 2) (or S-VIDEO IN 1 or 2)
jack on the TV and the
VIDEO (or S-VIDEO)output
jack on the VCR.
2
Connect a set of audio
cables between the AUDIO
IN (1 or 2) jacks on the TV
and the AUDIO output jacks
on the VCR.
3
Connect a video cable
between the VIDEO OUT 
jack on the TV and the 
VIDEO input jack on the 
VCR.
4
Connect a set of audio
cables between the AUDIO 
OUT jacks on...

Connections
English - 20
Connecting a Camcorder
The side panel jacks on your TV make it easy to connect a Camcorder to your TV.
You can use your camcorder to view tapes without using a VCR.
1
Locate the A/V output jacks
on the camcorder. They are
usually found on the side or
back of the camcorder.
2
Connect a set of audio
cables between the AUDIO 
IN jacks on the TV and the 
AUDIO output jacks on the
camcorder. If you have a
mono Camcorder, connect
L(mono) to the Camcorder
audio out using only one
audio...