Samsung HL-R7178W Dlp Tv Owners Instructions

English - 121
10) When multiple devices are connected, some devices may appear and then disappear periodically 
in the Device List. This is because some devices malfunction when multiple devices are connected.
If this occurs, you have to discover and remove the defective device from the connection by 
removing the devices one by one.  
11)  When multiple devices are connected, the response time may be relatively long when selecting a 
device. This may happen when there is a device(s) that malfunctions...

Using the D-Net
English - 122
Recording Tips
1) Recording using the Target List while also watching the screen being recorded. 
- Check that the AVHDD and DVHS devices are connected. 
- Select a source device to be recorded and press the Target button. 
- Select a device to be recorded from the Target List. 
2) Recording a program in the Program List of AVHDD using another device. 
- Select an AVHDD program to be recorded from the Program List and press Copy. 
- Select the target device from the Target...

English - 123
Continued...
Possible Solution
Only DTVs, STBs, AVHDDs, DVHSs and MPEG 
camcorder IEEE 1394 devices are controllable.
Other devices will display “UNCONTROLLABLE” in
the device list. 
Some supported devices may display as
“UNCONTROLLABLE” due to an initialization error.
➔If a device is supported but is displayed as 
“UNCONTROLLABLE”, reconnect the 1394 cable.
If this does not work, this is because the 
information about the device is unreadable due 
to an internal error.
A device, which has...

Using the D-Net
English - 124
Continued...
Possible Solution
This message appears when the connection speed of
the connected device and the device selected from the
Target List are different when copying data.
➔Connect a low speed device between the two 
devices. (See figure)
A 1394 device has a maximum connection 
speed which will be marked near the 
IEEE 1394 connector with an “S” number 
(i.e., S100,S200,S400). The higher the number, 
the faster the maximum connection speed. 
This TV has a maximum...

English - 125
Continued...
Possible Solution
Check if the current mode for DTV and STB is set to
analog by mistake. For AVHDD, check if the played
content reaches to the end. (Select the item from 
the content list again.) For DVHS, check if a D-VHS
tape is being used. If the camcorder supports the 
DV format, no picture will be displayed on the screen.
This message appears when the D-Net function is
being initialized.
Retry after a short wait to use the D-Net function.
This message appears when the...

Using the D-Net
English - 126
Possible Solution
This message appears if you have connected a 
1394 device or equipment other than a supported
device (DVHS, DTV, STB, AVHDD, Camcorder), or if
the connected device does not support the AVC
defined in the 1394 specifications, even if the device
is a supported device, when you have selected the
device to use it.
This message appears if there is a connection problem
when trying to use a D-Net device. 
This message appears if the AVHDD is booting when
trying to...

PC Display
BP68-00513A-00Eng(126~143)  6/3/05  3:15 PM  Page 127 

PC Display
English - 128
Using Your TV as a Computer (PC) Display
How to Connect Your PC to the TV
This figure shows the Standard Connector-jack panel. The actual configuration on your TV may be 
different, depending on the model.
Connecting a PC (15p D-SUB) to the TV
1
Connect a PC cable between
the PC Output jack on the 
PC and the RGB input jack 
(PC IN) on the TV.
2
Connect a Audio cable
between the Audio jack on 
the PC and the Audio input 
jacks (PC AUDIO IN) on 
the TV.
15Pin (D-Sub)
Cable
PCAudio...

English - 129
Setting up Your PC Software (Windows only)
The Windows display-settings for a typical computer are shown below. But the actual screens on your
PC will probably be different, depending upon your particular version of Windows and your particular
video card. But even if your actual screens look different, the same, basic set-up information will apply
in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.)
1. Right click the mouse on the Windows Desktop, 
then click...

PC Display
English - 130
NOTES
•The Modes Table conforms to the regulations of IBM/VESA and is prepared based on analog input
standards.
•The optimal resolution is 1920 x 1080 @ 60Hz.
•The optimal timing per each mode is the Vertical Frequency 60Hz. 
•Resolutions other than the resolutions above are not supported in PC mode.
•Although the OSD menu may shake when selecting a PC input of 1920 x 1080, this is not 
a defect. Therefore, please use the unit as usual.
Resolution
640 x 350
720 x 400
640 x 480...