Samsung HL P5063W DLP TV User Manual
Have a look at the manual Samsung HL P5063W DLP TV User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1705 Samsung manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Connecting a DVD PlayerThe rear panel jacks on your TV make it easy to connect a DVD player to your TV.Connecting to Y,P B,PR 1 Connect a set of audio cables between the COMPONENT (1 or 2) AUDIO (L,R) IN jacks on the TV and the AUDIO OUT jacks on the DVD player. 2 To enable Component video viewing, connect a set of video cables between the COMPONENT (1 or 2) VIDEO (Y, P B, P R) IN jacks on the TV and VIDEO (Y/P B/P Ror Y/C B/C R) OUT jacks on the DVD player. Note: For an explanation of Component video, see your DVD players owners manual. Connecting to audio and video jacks1 Connect a set of audio cables between the AUDIO IN (1 or 2) jacks on the TV and the AUDIO OUT jacks on the DVD player. 2 Connect a video cable between the VIDEO IN (1 or 2) jack on the TV and the VIDEO OUT jack on the DVD player. 21 Connecting a CamcorderThe side panel jacks on your TV make it easy to connect a camcorder to your TV. You can use your camcorder to view tapes without using a VCR.1 Locate the A/V output jacks on the camcorder. They are usually found on the side or back of the camcorder. 2 Connect a set of audio cables between the AUDIO IN jacks on the TV and the AUDIO OUT jacks on the camcorder. If you have mono camcorder, connect L(mono) to camcorder audio out using only one audio cable. 3 Connect a video cable between the VIDEO IN (or S-VIDEO IN) jack on the TV and the VIDEO OUT jack on the camcorder. The audio-video cables shown here are usually included with a Camcorder. (If not, check your local electronics store.) If your camcorder is stereo, you need to connect a set of two cables. Connections 20 Camcorder Output Jacks TV Side Panel CamcorderTV Rear Panel DVD Player Incoming Cable or Antenna TV Rear Panel DVD Player Incoming Cable or Antenna BP68-00283A-02(14~23) 5/6/04 11:30 AM Page 20
Connecting a DTV Set-Top BoxConnecting to Y,P B,PR 1 Connect a set of audio cables between the COMPONENT (1 or 2) AUDIO (L,R) IN jacks on the TV and the AUDIO OUT jacks on the Set-Top Box. 2 Connect a set of video cables between the COMPONENT (1 or 2) VIDEO (Y, P B, P R) IN jacks on the TV and VIDEO (Y/P B/P Ror Y/C B/C R) OUT jacks on the Set-Top Box. Note: For an explanation of Component video, see your Set Top Box owners manual. Connecting to DVI (Digital Visual Interface)1 Connect a set of audio cables between the DVI AUDIO (L,R) IN jacks on the TV and the AUDIO OUT jacks on the Set-Top Box. 2 Connect a video cable between the DVI IN jack on the TV and the DVI OUT jack on the Set-Top Box. 23 Connections 22 Connecting to R,G,B1 Connect a set of audio cables between the PC AUDIO (L,R) IN jacks on the TV and the AUDIO OUT jacks on the Set-Top Box. 2 Connect a video cable between the PC IN jack on the TV and the R.G.B OUT jack on the Set-Top Box. Connecting to HDMI (High Definition Multimedia Interface)1 Connect a HDMI cable between the HDMI IN jack on the TV and the HDMI OUT jack on the Set-Top Box. NOTE•Please check if the power of HDMI source is on, in case that you fail to select HDMI from the “Source List” even after you connected the cable of HDMI source (DTV Set-Top Box, DVD, etc.) to TV. TV Rear Panel DTV Set Top Box Incoming Cable or Antenna TV Rear Panel DTV Set Top Box Incoming Cable or AntennaTV Rear Panel DTV Set Top Box Incoming Cable or Antenna TV Rear Panel DTV Set Top Box Incoming Cable or Antenna BP68-00283A-02(14~23) 5/6/04 11:30 AM Page 22
Operation SAMSUNG BP68-00283A-02(24~45) 5/6/04 11:33 AM Page 24
Viewing the Menus1 Press the MENU button. The main menu is displayed. There are five menu groups: “Input”, “Picture”, “Sound”, “Channel” and “Setup”. 2 Press the … or † button to select to an item you want in the menu. Press the œ, √ or ENTER button to display, change, or use the selected items. Use the ENTER button to enter items in the menu. 3 Press the EXIT button to exit. Viewing the DisplayPress the INFO button on the remote control. The TV displays the current channel, the status of certain picture and sound settings and the current time. Operation 2627 Turning the TV On and OffPress the POWER button on the remote control. You can also use the POWER button on the front panel.Viewing the Menus and On-Screen DisplaysThe on-screen menu system allows you to control the settings of your TV. Access the on-screen menu system by pressing the MENU button on the remote control. Once the on-screen menu appears, use the …/†/œ/√/ENTER on your remote control to select menu items and make adjustments. You can also view the on-screen menu system and make some adjustments using the TV’s side panel buttons. Selecting the Menu LanguageChoose a language for the on-screen menus: English, Spanish or French. Input Source List : TV √ Edit Name √ Move Enter Exit Input Picture Sound Channel Setup Picture Mode : Standard √ Color Tone : Warm1 √ Size √ Digital NR : Off √ DNIe : On √ MCC √ Film Mode : Off √ PIP √ Move Enter Return Input Picture Sound Channel Setup 1 Press the MENU button. Press the … or † button to select “Setup”, then press the ENTER button. 2 Press the ENTER button to select “Language”. Press the … or † button to select the appropriate language, then press ENTER button. Press the EXIT button to exit. Setup Language : English √ Time √ V-Chip √ Caption √ Blue Screen : Off √ Melody : On √ Color Weakness √ PC √ Move Enter Return Input Picture Sound Channel Setup Setup Language : English Time V-Chip √ Caption Blue Screen : Off Melody : On Color Weakness PC Move Enter Return Input Picture Sound Channel Setup EnglishEspañolFrançais Selecting the Antenna InputYou can connect to two different signal sources by choosing the antenna input (1 or 2).1 Press the MENU button. Press the … or † button to select “Channel”, then press the ENTER button. 2 Press the ENTER button to select “Antenna”. Press the … or † button to select “Ant.1” or “Ant.2”, then press ENTER button. Press the EXIT button to exit. Channel Antenna : Ant.1 √ Air/CATV : Air √ Auto Program √ Add/Delete √ Favorite Channels √ Name √ Fine Tune √ ▼ MoreMove Enter Return Input Picture Sound Channel Setup Channel Antenna : Ant.1 Air/CATV : Air Auto Program Add/Delete Favorite Channels Name Fine Tune▼ MoreMove Enter Return Input Picture Sound Channel Setup Ant.1 Ant.2 Air 12 Signal Mono V-Chip Picture Dynamic Sound Standard SRS TSXT Stereo MTS Stereo - - : - - am BP68-00283A-02(24~45) 5/6/04 11:33 AM Page 26
Storing Channels in Memory (Automatic Method)First, select the correct signal source (“Air”, “STD”, “HRC” or “IRC”) as described on the previous page.1 Press the MENU button. Press the … or † button to select “Channel”, then press the ENTER button. 2 Press the … or † button to select “Auto Program”, then press the ENTER button. Press the ENTER button to start the auto program. The TV begins memorizing all of the available stations. Press the ENTER button at any time to interrupt the memorization process. Press the EXIT button to exit. Adding and Erasing ChannelsYou can add channels that were not memorized or delete unwanted channels from memory.1 Press the MENU button. Press the … or † button to select “Channel”, then press the ENTER button. 2 Press the … or † button to select “Add/Delete”, then press the ENTER button. Repeatedly pressing the ENTER button will alternate between add channel and delete channel. Press the CH or CH button (or number buttons) to switch to the appropriate channel, then repeat above. Press the EXIT button to exit. Alternate methodSimply press the ADD/DEL button on the remote control to add or delete channels. 29 Operation 28 Memorizing the ChannelsYour TV can memorize and store all of the available channels for both “off-air” (antenna) and cable channels. After the available channels are memorized, use the CH and CH buttons to scan through the channels. This eliminates the need to change channels by entering the channel digits. There are three steps for memorizing channels: selecting a broadcast source, memorizing the channels (automatic) and adding/deleting channels (manual). Channel Antenna : Ant.1 √ Air/CATV : Air √ Auto Program √ Add/Delete √ Favorite Channels √ Name √ Fine Tune √ ▼ MoreMove Enter Return Input Picture Sound Channel Setup Channel Antenna : Ant.1 √ Air/CATV : Air √ Auto Program √ Add/Delete √ Favorite Channels √ Name √ Fine Tune √ ▼ MoreMove Enter Return Input Picture Sound Channel Setup 1 Press the MENU button. Press the … or † button to select “Channel”, then press the ENTER button. 2 Press the … or † button to select “Air/CATV”, then press the ENTER button. If you are connected to an antenna, press the … or † button to select “Air”. If you connected cable, press the … or † button to select the type of cable system: “STD”, “HRC” or “IRC”. Press the EXIT button to exit. NOTES•“STD”, “HRC” and “IRC” identify various types of cable TV systems. Contact your local cable company to identify the type of cable system that exists in your particular area. At this point the signal source has been selected. Proceed to “Storing Channels in Memory”. •Subscription cable services require service-specific requirement for viewing. Channel Antenna : Ant.1 √ Air/CATV : Air √ Auto Program √ Add/Delete √ Favorite Channels √ Name √ Fine Tune √ ▼ MoreMove Enter Return Input Picture Sound Channel Setup Channel Antenna : Ant.1 Air/CATV : Air Auto Program Add/Delete Favorite Channels Name Fine Tune▼ MoreMove Enter Return Input Picture Sound Channel Setup Aire STD HRC IRC StartEnter Auto Program Return Air 12Not In Memory Change Add/Delete Enter Return Add Selecting the Video Signal SourceBefore your TV can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i.e., an antenna or a cable system). BP68-00283A-02(24~45) 5/6/04 11:33 AM Page 28
Selecting Your Favorite ChannelsYou can store your favorite channels for each available input source (such as TV and CATV). This allows you to quickly and easily find frequently watched channels by pressing the FAV.CH button on the remote control. Changing ChannelsYou can change channels on your TV by using the CH and CH buttons, or by direct selection using the number buttons. You can use the number buttons to tune to any channel (even one that has been erased or has not been memorized). 3031 Operation To Store Your Favorite Channels:1 Press the MENU button. Press the … or † button to select “Channel”, then press the ENTER button. 2 Press the … or † button to select “Favorite Channels”, then press the ENTER button. Press the … or † button to select a channel, then press the ENTER button. Press the ENTER button again to deselect the selected channel. Press the EXIT button to exit. To View Your Favorite Channels:Press the FAV.CH button repeatedly to jump from one favorite channel to another.NOTE•Only memorized channels can be set as Favorite channels. Channel Antenna : Ant.1 √ Air/CATV : Air √ Auto Program √ Add/Delete √ Favorite Channels √ Name √ Fine Tune √ ▼ MoreMove Enter Return Input Picture Sound Channel Setup Using the Channel ButtonsPress the CH or CH button to change channels. When you press the CH or CH button, the TV changes channels in sequence. You will see all the channels that the TV has memorized. (The TV must have memorized at least three channels.) You will not see channels that were either erased or not memorized.Using the Number ButtonsPress the number buttons to go directly to a channel. When you use the number buttons, you can directly select channels that were either erased or not memorized. For example, to select channel “27”, press the “2”, then “7”. The TV will change channels when you press the second number. To change to single-digit channels (0–9) faster, press the “0” before the single digit. (For channel “4”, press the “0”, then “4”.) To select a channel over 100, press the +100 button. (For channel “122”, press the +100 button, then “2”, then “2”.)Using the Previous ChannelPress the PRE-CH button. The TV changes to the last channel you were watching. Favorite Channels Enter Input Picture Sound Channel Setup Return Air 2 - - - - ✔ Air 3 - - - - Air 4 - - - - Air 5 - - - - Air 6 - - - - Air 7 - - - - Air 8 - - - - ▼Move BP68-00283A-02(24~45) 5/6/04 11:33 AM Page 30
Scanning the ChannelsThe TV automatically scan all of the channels it has memorized. 33 Labeling the ChannelsUse this feature to assign an easy-to-remember label to any channel (i.e., “CBS”, “ESPN”, “PBS2”, CNN1”, etc.) A label consists of five fields, where each field is a letter, a number or a blank. When the INFO button is pressed, the channel label will appear next to the channel number. Operation 32 1 Press the MENU button. Press the … or † button to select “Channel”, then press the ENTER button. 2 Press the … or † button to select “Scan”, then press the ENTER button. The TV scans all of the channels memorized. Press the EXIT button to exit. NOTE• When the “ANT 2 IN” mode is selected, the channel scan function works on the main picture only. Air 3 Air 4ReturnScanChannel Antenna : Ant.1 √ Air/CATV : Air √ Auto Program √ Add/Delete √ Favorite Channels √ Name √ Fine Tune √ ▼ MoreMove Enter Return Input Picture Sound Channel Setup Channel ▲ More LNA : On √ Scan √ Move Enter Return Input Picture Sound Channel Setup 1 Press the CH or CH button to tune to the channel that will be labeled. 2 Press the MENU button. Press the … or † button to select “Channel”, then press the ENTER button. Press the … or † button to select “Name”, then press the ENTER button. 3 Press the …/†/œ/√ button to move to the channel to be assigned to a new name, then press the ENTER button. Press the … or † button to select a letter, a number or a blank. (Results in this sequence: A...Z, ✽, blank, 0...9, -). 4 Press the √ button to switch to the next field, which will be selected. Select a second letter or digit pressing … or † button, as above. Repeat the process to select the last two digits. When you have finished, press the ENTER button. To erase the assigned new name, select “Clear” by pressing the …/†/œ/√ button, then press the ENTER button. Press the EXIT button to exit. Name Move Adjust Return Input Picture Sound Channel Setup ClearClearClearClearClear ▼ Air 2A Air 3 ---- Air 4 ---- Air 5 ---- Air 6 ----▲ ▼ Name Move Enter Return Input Picture Sound Channel Setup ClearClearClearClearClear ▼ Air 2CNN2 Air 3 ---- Air 4 ---- Air 5 ---- Air 6 ----Channel Antenna : Ant.1 √ Air/CATV : Air √ Auto Program √ Add/Delete √ Favorite Channels √ Name √ Fine Tune √ ▼ MoreMove Enter Return Input Picture Sound Channel Setup NOTE•If you add or delete the TV channel, the labeled channels list will also be added or deleted. Enter Return BP68-00283A-02(24~45) 5/6/04 11:33 AM Page 32
Picture ControlYou can use the on-screen menus to change the “Contrast”, “Brightness”, “Sharpness”, “Color” and “Tint” according to personal preference. (Alternatively, you can use one of the automatic settings. See next page.) Using Automatic Picture SettingsYour TV has automatic picture settings (“Dynamic”, “Standard” and “Cinema”) that are preset at the factory. You can activate either “Dynamic”, “Standard” or “Cinema” by pressing the P.MODE button (or by making a selection from the menu). Or, you can select “Custom” which automatically recalls your personalized picture settings.1 Press the MENU button. Press the … or † button to select “Picture”, then press the ENTER button. 2 Press the ENTER button to select “Mode”. 3 Press the ENTER button again to select “Mode”. Press the … or † button to select a particular item, then press the ENTER button. Press the EXIT button to exit. Alternate methodPress the P.MODE button on the remote control repeatedly to select one of the standard picture settings. •Choose “Dynamic” for viewing the TV during the day or when there is a bright light in the room. •Choose “Standard” for the standard factory settings. •Choose “Cinema” when viewing a movie. 35 Operation 34 Standard Customizing the Picture1 Press the MENU button. Press the … or † button to select “Picture”, then press the ENTER button. 2 Press the ENTER button to select “Mode”. 3 Press the … or † button to select a particular item, then press the ENTER button. Press the œ or √ button to increase or decrease the value of a particular item. Resetting the Picture Settings to the Factory DefaultsYou can return to the factory default picture settings.4 Press the MENU button to display the “Mode” menu. Press the … or † button to select “Reset”, then press the ENTER button. The previously adjusted picture settings will be reset to the factory defaults. ▲ Contrast ▼ 90 Picture Mode : Standard √ Color Tone : Warm1 √ Size √ Digital NR : Off √ DNIe : On √ MCC √ Film Mode : Off √ PIP √ Move Enter Return Input Picture Sound Channel Setup Mode Mode : Standard √ Contrast 90 Brightness 50 Sharpness 50 Color 50 Tint 50 50 Reset Move Enter Return Input Picture Sound Channel Setup Picture Mode : Standard √ Color Tone : Warm1 √ Size √ Digital NR : Off √ DNIe : On √ MCC √ Film Mode : Off √ PIP √ Move Enter Return Input Picture Sound Channel Setup Mode Mode : Standard √ Contrast 90 Brightness 50 Sharpness 50 Color 50 Tint 50 50 Reset Move Enter Return Input Picture Sound Channel Setup Mode Mode: Standard Contrast 90 Brightness 50 Sharpness 50 Color 50 Tint 50 50 Reset Move Enter Return Input Picture Sound Channel Setup Dynamic Standard Cinema NOTE•“Tint” doesn’t operate in PC, DVI, HDMI or 480p-Component or higher modes. Mode Mode : Standard √ Contrast 90 Brightness 50 Sharpness 50 Color 50 Tint 50 50 Reset Move Enter Return Input Picture Sound Channel Setup BP68-00283A-02(24~45) 5/6/04 11:33 AM Page 34
3 Press the œ or √ button to select a particular item to be changed. Press the … or † button to increase or decrease the value of a particular item. Press the EXIT button to exit. Using Automatic Sound SettingsYour TV has automatic sound settings (“Standard”, “Music”, “Movie” and “Speech”) that are preset at the factory. You can activate these sound settings by pressing the S.MODE button (or by making a selection from the menu), or you can select “Custom”, which automatically recalls your personalized sound settings.1 Press the MENU button. Press the … or † button to select “Sound”, then press the ENTER button. 2 Press the ENTER button to select “Mode”. Press the … or † button to select a particular item, then press the ENTER button. Press the EXIT button to exit. Alternate methodPress the S.MODE button on the remote control repeatedly to select one of the standard sound settings. •Choose “Standard” for the standard factory settings. •Choose “Music” when watching music videos or concerts. •Choose “Movie” when watching movies. •Choose “Speech” when watching a show that is mostly dialogue (i.e., news). •Choose “Custom” to recall your personalized settings. Sound ControlYou can control and customize the sound levels and settings of the TV with the remote control. 3637 Operation StandardEqualizerMove Adjust Return Input Picture Sound Channel Setup Adjusting the VolumePress the VOL+ or VOL– buttons to increase or decrease the volume.Using the MUTE ButtonAt any time, you can temporarily cut off the sound. Press the MUTE button on the remote control. The message “Mute” is displayed and the sound cuts off. To turn mute off press the MUTE button again or, press either the VOL+ or VOL– button.Customizing the SoundThe sound settings can be adjusted to suit your personal preference. (Alternatively, you can use one of the automatic settings. See next page.)1 Press the MENU button. Press the … or † button to select “Sound”, then press the ENTER button. 2 Press the … or † button to select “Equalizer”, then press the ENTER button. Continued... Mute Sound Mode : Standard √ Equalizer √ SRS TSXT : Off √ MTS : Stereo √ Auto Volume : Off √ Internal Mute : Off √ Move Enter Return Input Picture Sound Channel Setup Sound Mode : Standard √ Equalizer √ SRS TSXT : Off √ MTS : Stereo √ Auto Volume : Off √ Internal Mute : Off √ Move Enter Return Input Picture Sound Channel Setup Balance 100Hz 300Hz 1KHz 3KHz 10KHzR L + 0 -+ 0 -Sound Mode : Standard √ Equalizer √ SRS TSXT : Off √ MTS : Stereo √ Auto Volume : Off √ Internal Mute : Off √ Move Enter Return Input Picture Sound Channel Setup Sound Mode : Standard Equalizer SRS TSXT : Off MTS : Stereo Auto Volume : Off Internal Mute : Off Move Enter Return Input Picture Sound Channel Setup Standard Music Movie Speech Custom BP68-00283A-02(24~45) 5/6/04 11:33 AM Page 36
Setting the TimersThis TV can be set to turn on or off automatically at specific times that you choose. Before using the timers, you must set the TV’s clock, as described previously.Setting the On/Off Timer1 Press the MENU button. Press the … or † button to select “Setup”, then press the ENTER button. 2 Press the … or † button to select “Time”, then press the ENTER button. Press the … or † button to select “On Timer”, then press the ENTER button. 3 Press the … or † button to adjust “Hour”, then press the √ button to move to the next step. Set other items using the same method as above. When finished, press the MENU button to return. 4 Press the … or † button to select “Off Timer”, then press the ENTER button. 5 Press the … or † button to adjust “Hour”, then press the √ button to move to the next step. Set other items using the same method as above. Press the EXIT button to exit. 39 Setting the ClockSetting the clock is necessary in order to use the various timer features of the TV. Also, you can check the time while watching the TV. (Just press the INFO button.) Operation 38 Setup Language : English √ Time √ V-Chip √ Caption √ Blue Screen : Off √ Melody : On √ Color Weakness √ PC √ Move Enter Return Input Picture Sound Channel Setup Time Clock Set 10 : 30 am √ Sleep Timer Off √ On Timer Off √ Off Timer Off √ Move Enter Return Input Picture Sound Channel Setup 1 Press the MENU button. Press the … or † button to select “Setup”, then press the ENTER button. Press the … or † button to select “Time”, then press the ENTER button. 2 Press the ENTER button to select “Clock Set”. 3 Press the œ or √ button to move to “Hour”, “Min” or “am/pm”. Set the clock you want by pressing the … or † button, then press the ENTER button. Press the EXIT button to exit. NOTE•The current time will appear every time you press the INFO button. Setup Language : English √ Time √ V-Chip √ Caption √ Blue Screen : Off √ Melody : On √ Color Weakness √ PC √ Move Enter Return Input Picture Sound Channel Setup Time Clock Set - - : - - am √ Sleep Timer Off √ On Timer Off √ Off Timer Off √ Move Enter Return Input Picture Sound Channel Setup Clock SetMove Adjust Return Input Picture Sound Channel Setup Hour Min am/pm 12 0 0 am▲ ▼ On TimerMove Adjust Return Input Picture Sound Channel Setup Hour Min am/pm 12 0 0 am▲ ▼Ch Vol. Activation 03 10 No Time Clock Set 10 : 30 am √ Sleep Timer Off √ On Timer 06 : 30 am √ Off Timer Off √ Move Enter Return Input Picture Sound Channel Setup Off TimerMove Adjust Return Input Picture Sound Channel Setup Hour Min am/pm 12 0 0 am▲ ▼ ActivationNo Absent Power OffWhen you set the timer “On”, your television will eventually be turned off, if you do not operate any controls during the 3 hours after the TV is turned on by timer. This function is available in only the timer “On” mode and will prevent a leakage accident or overheating, caused by your TV left on for a long time due to the timer “On” (when you are away on holiday, for example). BP68-00283A-02(24~45) 5/6/04 11:33 AM Page 38