Samsung Hd160jj P Manual
Have a look at the manual Samsung Hd160jj P Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1705 Samsung manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Spinpoint T133 series • Ultra ATA-100 Compliant • Fluid Dynamic Bearing Spindle Motor Technology • High Speed Dual Digital Signal Processor (DSP) Based Architecture • ATA S.M.A.R.T. Compliant • ATA Security Mode Feature Set • ATA Host Protected Area Feature Set • ATA Automatic Acoustic Management Feature Set • ATA 48-bit Address Feature Set • ATA Streaming Feature Set 4 • ATA Device Configuration Overlay Feature Set • Multi-Burst On-The-Fly Error Correction • NoiseGuard™ • SilentSeek™300.0/400.0GB Capacity 1 Model PATA,8MB300GB HD300LD 400GBHD400LD Specifications are subject to change without notice.1. 1MB=1,000,000 Bytes 1GB=1,000,000,000 Bytes *Accessible capacity may vary as some OS uses binary numbering system for reported capacity2. 128KB is used for firmware 3. For ATA-6 interface models only 4. 30% duty cycle, random seek 5. Power based on enabled DIPM and SATA 3.0Gbps speed PERFORMANCE SPECIFICATIONSInterface ATA 6 Bytes per Sector 512Buffer DRAM Size 2 8 MB PERFORMANCE SPECIFICATIONS Read Seek Time (typ.)-Track to track 0.8 ms-Average 8.9 ms-Full Stroke 18 ms-Average Latency 4.17 ms-Rotational Speed 7,200 rpmMaximum Data Transfer Rate-Media to/from Buffer(max.) 742/1000Mbits/sec-Buffer to/from Host 100 MB/secDrive Ready Time(typ.)10 secRELIABILITY SPECIFICATIONSNon-recoverable Read Error 1 sector in 10 14bits MTBF 600,000 POHStart/Stop Cycles(Ambient) 50,000Component Design Life 5 yearsACOUSTICS (AVERAGE SOUND POWER)-Idle 2.7 Bel-Random Read/Write 2.9 Bel ENVIRONMENTAL SPECIFICATIONSTemperature-Operating 0~60°C-Non-operating -40~70°C-Thermal Gradient (max.) 20°C/hrHumidity (non-condensing)-Operating 5~90 %-Non-operating 5~95 %Linear Shock (1/2 sine pulse)-Operating, 2ms 63 G-Non-operating, 2ms 300 GVibration (swept sine, 0.5 octave per minute) Operating 5 - 300 - 5 Hz 1.0 G0-p Non-operating5 - 500 - 5 Hz 2.0 G0-pAltitude (relative to sea level)-Operating -1,000 to 10,000 feet-Non-operating -1,000 to 40,000 feetPOWER REQUIREMENTS Voltage +5V° 5% / +12V° 10% Spin Up Current(max.) 880 / 2250 mASeek 5 (typ.) 9.2 W Read on-Track(typ.) 8.4 WIdle(typ.) 8.0 WStandby(typ.) 0.7 WSleep(typ.) 0.45 WPHYSICAL DIMENSIONHeight 1 inWidth 4 inDepth 5.75 inWeight 1.44 lb *Notes:Design and specifications are subject to change without prior notice
Spinpoint P120S series • 125GB Formatted Capacity Per Disk • Serial ATA 3.0Gbps Interface Support • SATA Native Command Queuing Feature set • Device Initiated SATA Power Management • Staggered Spin-up Support • High Speed Dual Digital Signal Processor (DSP) Based Architecture • ATA S.M.A.R.T. Compliant • ATA Automatic Acoustic Management Feature Set • ATA 48-bit Address Feature Set • ATA Streaming Feature Set • ATA Device Configuration Overlay Feature Set • NoiseGuard™ • SilentSeek™200.0/250.0GB Capacity 1 Model200GB SP2004C 250GBSP2504C 1. 1MB=1,000,000 Bytes 1GB=1,000,000,000 Bytes *Accessible capacity may vary as some OS uses binary numbering system for reported capacity2. Upper 128 KB is used for firmware 3. 30% duty cycle, random seek 4. Power consumption with / without slumber mode DRIVE CONFIGURATIONInterface Serial ATA 3.0 GbpsBuffer DRAM Size 2 8 MB Bytes per Sector 512PERFORMANCE SPECIFICATIONSRead Seek Time (typ.)-Track to Track 0.8 ms-Average 8.9 ms-Full Stroke 18 ms-Average Latency 4.17 ms-Rotational Speed 7,200 rpmData Transfer Rate-Media to/from Buffer (max.) 973 MB/sec-Buffer to/from Host (max.) 300 MB/sec-Drive Ready Time (typ.) 7 secRELIABILITY SPECIFICATIONSNon-recoverable Read Error 1 sector in 10 14bits MTBF 600,000 POHStart/Stop Cycles (Ambient) 50,000Component Design Life 5 yearsACOUSTICS (AVERAGE SOUND POWER)-Idle 2.5 Bel-Random Read/Write 2.8 Bel ENVIRONMENTAL SPECIFICATIONSTemperature-Operating 0 ~ 60 ºC-Non-operating -40 ~ 70 ºC-Thermal Gradient (max.) 20 ºC/hrHumidity (non-condensing)-Operating 5 ~ 90 %-Non-operating 5 ~ 95 %Linear Shock (1/2 sine pulse)-Operating, 2ms 63G-Non-operating, 2ms 350GVibration (swept sine, 1 octave per minute) Operating 5 ~ 21 Hz 0.034” (double amplitude)21 ~ 300 Hz 1.5 Gp-p Non-operating 5 ~ 21 Hz 0.195” (double amplitude)21 ~ 500 Hz 8 Gp-pAltitude (relative to sea level)-Operating -1,000 to 10,000 ft-Non-operating -1,000 to 40,000 ftPOWER REQUIREMENTS Voltage +5V±5%,+12V±10%Spin Up Current (max.) 650 / 1900 mASeek (typ.) 3 9.5 W Read/Write On-Track (typ.) 8.5 WIdle (typ.) 7.5 WStandby (typ.) 0.7/1.5 W 4 Sleep (typ.) 0.7/1.5 W 4 PHYSICAL DIMENSIONHeight 1 inWidth 4 inDepth 5.75 inWeight 1.4 lb *Notes:Design and specifications are subject to change without prior notice
Spinpoint P120 series • 125GB Formatted Capacity Per Disk • Ultra ATA-133 Interface Support • Fluid Dynamic Bearing Spindle Motor Technology • High Speed Dual Digital Signal Processor (DSP) Based Architecture • ATA S.M.A.R.T. Compliant • ATA Security Mode Feature Set • ATA Host Protected Area Feature Set • ATA Automatic Acoustic Management Feature Set • ATA 48-bit Address Feature Set • ATA Streaming Feature Set • ATA Device Configuration Overlay Feature Set • NoiseGuard™ • SilentSeek™200.0/250.0GB Capacity 1 Model200GB SP2014N 250GBSP2514N DRIVE CONFIGURATIONInterface ATA 7Bytes per Sector 512Buffer DRAM Size 2 8 Mbytes PERFORMANCE SPECIFICATIONS Read Seek Time (typical)-Track to track 0.8 ms-Average 8.9 ms-Full Stroke 18 ms-Average Latency 4.17 ms-Rotational Speed 7,200 rpmData Transfer Rate-Media to/from Buffer(max.) 973 Mbits/s-Buffer to/from Host(max.) 133 Mbytes/sDrive Ready Time(typical)7 secRELIABILITY SPECIFICATIONSNon-recoverable Read Error 1 sector in 10 14bits MTBF 600,000 POHStart/Stop Cycles(Ambient) 50,000Component Design Life 5 yearsACOUSTICS (AVERAGE SOUND POWER)-Idle 2.5 Bel-Random Read/Write 2.8 Bel ENVIRONMENTAL SPECIFICATIONSTemperature-Operating 0~60°C-Non-operating -40~70°C-Thermal Gradient (max.) 20°C/hrHumidity (non-condensing)-Operating 5~90%-Non-operating 5~95% Linear Shock (1/2 sine pulse)-Operating, 2ms 63 G-Non-operating, 2ms 350 GVibration (swept sine, 1 octave per minute) Operating 5 ~ 21 Hz 0.034 (double amplitude)21 ~ 300 Hz 1.5 Gp-p Non-operating 5 ~ 21 Hz 0.195 (double amplitude)21 ~ 500 Hz 8 Gp-pAltitude (relative to sea level)-Operating -1,000 to 10,000 feet-Non-operating -1,000 to 40,000 feetPOWER REQUIREMENTSVoltage +5V° 5% / +12V° 10% Spin Up Current(max.) 650 / 1900 mARead/Write On-Track(typ.) 7.5 WSeek (typ.) 3 9.0 W Idle(typ.) 7.0 WStandby(typ.) 0.5 WSleep(typ.) 0.4 WPHYSICAL DIMENSIONHeight 1 inWidth 4 inDepth 5.75 inWeight 1.4 lb1. 1MB=1,000,000 Bytes 1GB=1,000,000,000 Bytes *Accessible capacity may vary as some OS uses binary numbering system for reported capacity2. Upper 128 KB is used for firmware 3. 30% duty cycle, random seek 4. Backward compatible with UDMA 33/66/100 Factory default UDMA100 unless customer request *Notes:Design and specifications are subject to change without prior notice 8MB
Spinpoint P80SD series • 80GB Formatted Capacity Per Disk • Native Serial ATA 3.0Gbps with Native Command Queuing (NCQ) • Fluid Dynamic Bearing Spindle Motor Technology • High Speed Dual Digital Signal Processor (DSP) Based Architecture • ATA SMART Compliant • ATA Security Mode Feature Set • ATA Host Protected Area Feature Set • ATA Automatic Acoustic Management Feature Set • ATA 48-bit Address Feature Set • ATA Streaming Feature Set • ATA Power Up In Standby Feature Set • ATA Device Configuration Overlay Feature Set • Permuted RLL/ECC On-The-Fly Error Correction • RoHS-compliant • NoiseGuard™ • SilentSeek™ • Hot-Plug & Hot-Swap capable40.0/80.0/120.0/160.0GB Capacity 1 Model40GB HD040GJ 80GBHD080HJ 120GBHD120IJ 160GBHD160JJ Specifications are subject to change without notice.1. 1MB=1,000,000 Bytes 1GB=1,000,000,000 Bytes *Accessible capacity may vary as some OS uses binary numbering system for reported capacity2. 384 KB is used for firmware 3. 30% duty cycle, random seek 4. Unless otherwise specified, specifications are for both 1 and 2 disk configurations of Serial-ATA models 5. Power consumption with / without slumber mode DRIVE CONFIGURATIONInterface Serial ATA 3.0 GbpsBuffer DRAM Size 2 8 MB Bytes per Sector 512PERFORMANCE SPECIFICATIONSRead Seek Time (typ.)-Track to track 0.8 ms-Average 8.9 ms-Full Stroke 18.0 ms-Average Latency 4.17 ms-Rotational Speed 7,200 rpmMaximum Data Transfer Rate-Media to/from Buffer 845-Buffer to/from Host 300 MB/secDrive Ready Time (typ.)7 secRELIABILITY SPECIFICATIONSNon-recoverable Read Error 1 sector in 10 14bits MTBF 500,000 POHStart/Stop Cycles (Ambient) 50,000Component Design Life 5 yearsACOUSTICS (AVERAGE SOUND POWER)-Idle 2.5 Bel-Random Read/Write 2.8 Bel ENVIRONMENTAL SPECIFICATIONSTemperature-Operating 5~55°C-Non-operating -40~70°C-Thermal Gradient (max.) 20°C/hrHumidity (non-condensing)-Operating 5~90 %-Non-operating 5~95 %Linear Shock (1/2 sine pulse)-Operating, 2ms 63 G-Non-operating, 2ms 350 GVibration (swept sine, 1 octave per minute) Operating 5 ~ 21 Hz 0.034 (double amplitude)21 ~ 300 Hz 1.5 Gp-p Non-operating 5 ~ 21 Hz 0.195 (double amplitude)21 ~ 500 Hz 8 Gp-pAltitude (relative to sea level)-Operating -1,000 to 10,000 feet-Non-operating -1,000 to 40,000 feetPOWER REQUIREMENTS Voltage +5V 5% / 12V 10% Spin Up Current(max.) 650 / 1900 mASeek 3 (typ.) 9.0 W Read/Write On-Track(typ.) 8.0 WIdle(typ.) 6.8 WStandby(typ.) 0.7 / 1.5 W 5 Sleep(typ.) 0.7 / 1.5 W 5 PHYSICAL DIMENSIONHeight 1 inWidth 4 inDepth 5.75 inWeight 1.45 lb *Notes:Design and specifications are subject to change without prior notice
DRIVE CONFIGURATIONInterface ATA 6 Bytes per Sector 512Buffer DRAM Size 1 2/8 Mbytes PERFORMANCE SPECIFICATIONS Read Seek Time (typical)-Track to track 0.8 ms-Average 8.9 ms-Full Stroke 18.0 ms-Average Latency 4.17 ms-Rotational Speed 7,200 rpmData Transfer Rate-Media to/from Buffer(max.) 840 Mbits/s-Buffer to/from Host(max.) 133 Mbytes/sDrive Ready Time(typical)7 secRELIABILITY SPECIFICATIONSNon-recoverable Read Error 1 sector in 10 14bits MTBF(POH) 500,000 POHStart/Stop Cycles 50,000Component Design Life 5 yearsACOUSTICS (AVERAGE SOUND POWER)-Idle 2.7 Bel-Random Read/Write 2.8 Bel ENVIRONMENTAL SPECIFICATIONSTemperature-Operating 5~55°C-Non-operating -40~70°C-Thermal Gradient (max.) 20°C/hrHumidity (non-condensing)-Operating 5~90%-Non-operating 5~95% Linear Shock (1/2 sine pulse)-Operating, 2ms 63 G-Non-operating, 2ms 350 GVibration (swept sine, 1 octave per minute) Operating 5 ~ 21 Hz 0.034 (double amplitude)21 ~ 300 Hz 1.5 Gp-p Non-operating 5 ~ 21 Hz 0.195 (double amplitude)21 ~ 500 Hz 8 Gp-pAltitude (relative to sea level)-Operating -1,000 to 10,000 feet-Non-operating -1,000 to 40,000 feetPOWER REQUIREMENTSVoltage 5V° 5% / 12V° 10% Spin Up Current(max.) 780 / 2250 mARead/Write On-Track(typ.) 8.0 WSeek (typ.) 2 9.0 W Idle(typ.) 7.2 WStandby(typ.) 0.4 WSleep(typ.) 0.4 WPHYSICAL DIMENSIONHeight 1 inchWidth 4 inchesDepth 5.75 inchesWeight 1.45 pounds Spinpoint P80 series • 80GB Formatted Capacity Per Disk • Ultra ATA-133 Compatible • Fluid Dynamic Bearing Spindle Motor Technology • High Speed Dual Digital Signal Processor (DSP) Based Architecture • ATA S.M.A.R.T. Compliant • ATA Security Mode Feature Set • ATA Host Protected Area Feature Set • ATA Automatic Acoustic Management Feature Set • ATA 48-bit Address Feature Set • ATA Streaming Feature Set (Optional) • ATA Device Configuration Overlay Feature Set • Multi-Burst On-The-Fly Error Correction • NoiseGuard™ • SilentSeek™ • ImpacGuard™80.0/120.0/160.0GB *Accessible capacity may vary as some OS uses binary numbering system for reported capacity1. 128 KB is used for firmware 2. 30% duty cycle, random seek Capacity 1 Model 2MB 8MB80GB SP0842N 120GBSP1243N SP1253N 160GBSP1644N SP1654N 1MB = 1,000,000 Bytes. 1GB = 1,000,000,000 Bytes *Notes:Design and specifications are subject to change without prior notice
Spinpoint M80S series • 80GB Formatted Capacity Per Disk • TuMR head with wireless suspension design • Serial ATA 1.5Gbps Interface Support • SATA Native Command Queuing Feature set • Device Initiated SATA Power Management • Fluid Dynamic Bearing Spindle Motor Technology • Load/Unload Head Technology • ATA Security Mode Feature Set • ATA SMART Feature Set • ATA Automatic Acoustic Management Feature Set • ATA Device Configuration Overlay Feature Set • Multi-Burst On-The-Fly Error Correction • SilentSeek™ • Hybrid Latch System for Reliability and Quietness80.0/120.0/160.0GB Capacity 1 Model80GB HM080HI 160GBHM160JI 120GBHM120II Specifications are subject to change without notice.1. 1MB=1,000,000 Bytes 1GB=1,000,000,000 Bytes *Accessible capacity may vary as some OS uses binary numbering system for reported capacity2. Upper 128 KB is used for firmware 3. Power-On to Drive Ready 4. 30% duty cycle, random seek 5. Power requirements based on 1.5Gbps speed 6. Unless otherwise specified, specifications are for 2-disk configuration DRIVE CONFIGURATIONInterface SATA 1.5GbpsBuffer DRAM Size 3 8 Mbytes Bytes per Sector 512PERFORMANCE SPECIFICATIONSRead Seek Time (typ.)-Track to Track 2 ms-Average 12 ms-Full Stroke 22 ms-Average Latency 5.6 ms-Rotational Speed 5,400 rpmData Transfer Rate-Media to/from Buffer (max.) 530Mb/s-Buffer to/from Host (max.) 150MB/s-Drive Ready Time (typ.) 3 4 sec RELIABILITY SPECIFICATIONSNon-recoverable Read Error 1 sector in 10 14bits MTBF 330,000 POHControlloed Ramp L/UL 600,000ACOUSTICS (AVERAGE SOUND POWER) -Idle 1-Disk 2.2 Bel 2-Disk 2.4 Bel -Random Read/Write 1-Disk 2.4 Bel2-Disk 2.6 Bel ENVIRONMENTAL SPECIFICATIONSTemperature-Operating 5 ~ 55 ºC-Non-operating -40 ~ 70 ºCHumidity (non-condensing)-Operating 5 ~ 90 %-Non-operating 5 ~ 95 %Linear Shock (1/2 sine pulse)-Operating, 2ms 325G-Non-operating, 1ms 1000GVibration (swept sine, 1/4 octave per minute) Operating5 ~ 500 Hz 1.0 Go-p Non-operating 10 ~21 Hz 0.195 in(double amp) 21 ~ 500Hz 5 Go-p500~800Hz 3 Go-pAltitude (relative to sea level)-Operating -1000 to 10000 ft-Non-operating -1400 to 50000 ftPOWER REQUIREMENTS Voltage +5V±5%Spin Up (max.) 4.5 WSeek (typ.) 5 2.1 W Read/Write On-Track (typ.) 2.0 WLow Power Idle (typ.) 0.60 WStandby (typ.) 0.25 WSleep (typ.) 0.20 WPHYSICAL DIMENSIONHeight 0.37 inWidth 3.94 inDepth 2.75 inWeight 0.22 lb *Notes:Design and specifications are subject to change without prior notice
Spinpoint M80 series • 80GB Formatted Capacity Per Disk • TuMR head with wireless suspension design • Ultra ATA-100 Interface • Fluid Dynamic Bearing Spindle Motor Technology • Load/Unload Head Technology • ATA Security Mode Feature Set • ATA SMART Feature Set • ATA Automatic Acoustic Management Feature Set • ATA Device Configuration Overlay Feature Set • Multi-Burst On-The-Fly Error Correction • SilentSeek™ • Hybrid Latch System for Reliability and Quietness80.0/120.0/160.0GB *Notes:Design and specifications are subject to change without prior noticeDRIVE CONFIGURATIONInterface ATA 6Buffer DRAM Size 3 8 Mbytes Bytes per Sector 512PERFORMANCE SPECIFICATIONSRead Seek Time (typ.)-Track to Track 2 ms-Average 12 ms-Full Stroke 22 ms-Average Latency 5.6 ms-Rotational Speed 5,400 rpmData Transfer Rate-Media to/from Buffer (max.) 530Mb/s-Buffer to/from Host (max.) 150MB/s-Drive Ready Time (typ.) 3 4 sec RELIABILITY SPECIFICATIONSNon-recoverable Read Error 1 sector in 10 14bits MTBF 330,000 POHControlloed Ramp L/UL 600,000ACOUSTICS (AVERAGE SOUND POWER) -Idle 1-Disk 2.2 Bel 2-Disk 2.4 Bel -Random Read/Write 1-Disk 2.4 Bel2-Disk 2.6 Bel ENVIRONMENTAL SPECIFICATIONSTemperature-Operating 5 ~ 55 ºC-Non-operating -40 ~ 70 ºCHumidity (non-condensing)-Operating 5 ~ 90 %-Non-operating 5 ~ 95 %Linear Shock (1/2 sine pulse)-Operating, 2ms 325G-Non-operating, 1ms 1000GVibration (swept sine, 1/4 octave per minute) Operating5 ~ 500 Hz 1.0 Go-p Non-operating 10 ~21 Hz 0.195 in(double amp) 21 ~ 500Hz 5 Go-p500~800Hz 3 Go-pAltitude (relative to sea level)-Operating -1000 to 10000 ft-Non-operating -1400 to 50000 ftPOWER REQUIREMENTS Voltage +5V±5%Spin Up (max.) 4.5 WSeek (typ.) 5 2.1 W Read/Write On-Track (typ.) 2.0 WLow Power Idle (typ.) 0.60 WStandby (typ.) 0.25 WSleep (typ.) 0.10 WPHYSICAL DIMENSIONHeight 0.37 inWidth 3.94 inDepth 2.75 inWeight 0.22 lb Capacity 1 Model80GB HM080HC 160GBHM160JC 120GBHM120IC Specifications are subject to change without notice.1. 1MB=1,000,000 Bytes 1GB=1,000,000,000 Bytes *Accessible capacity may vary as some OS uses binary numbering system for reported capacity2. Upper 128 KB is used for firmware 3. Power-On to Drive Ready 4. 30% duty cycle, random seek 5. Power requirements based on 1.5Gbps speed 6. Unless otherwise specified, specifications are for 2-disk configuration
Spinpoint M60S series • Serial ATA 1.5Gbps(3.0Gbps) Interface Support • SATA Native Command Queuing Feature set • Device Initiated Power Management • 60GB Formatted Capacity Per Disk • GMR/TuMR head with wireless suspension design • Fluid Dynamic Bearing Spindle Motor Technology • Load/Unload Head Technology • ATA Security Mode Feature Set • ATA SMART Feature Set • ATA Automatic Acoustic Management Feature Set • ATA Device Configuration Overlay Feature Set • Multi-Burst On-The-Fly Error Correction • Hybrid Latch System for Reliability and Quietness • SilentSeekTM40.0/60.0/80.0/100.0/120.0GB Capacity 1 Model40GB HM040HI 60GBHM060HI 80GBHM080II 120GBHM120JI 100GBHM100JI 1. 1MB=1,000,000 Bytes 1GB=1,000,000,000 Bytes *Accessible capacity may vary as some OS uses binary numbering system for reported capacity2. SATA interface speed switchable with Jumper 3. Upper 128 KB is used for firmware 4. Power-On to Drive Ready 5. 30% duty cycle, random seek 6. Power requirements based on 1.5Gbps speed 7. Unless otherwise specified, specifications are for 2-disk configuration DRIVE CONFIGURATIONInterface SATA 1.5Gbps(3.0Gbps) 3 Buffer DRAM Size 3 8 Mbytes Bytes per Sector 512PERFORMANCE SPECIFICATIONSRead Seek Time (typ.)-Track to Track 2 ms-Average 12 ms-Full Stroke 22 ms-Average Latency 5.6 ms-Rotational Speed 5,400 rpmData Transfer Rate-Media to/from Buffer (max.) 495Mb/s-Buffer to/from Host (max.) 150MB/s-Drive Ready Time (typ.) 4 4 sec RELIABILITY SPECIFICATIONSNon-recoverable Read Error 1 sector in 10 14bits MTBF 330,000 POHControlloed Ramp L/UL 600,000ACOUSTICS (AVERAGE SOUND POWER) -Idle 1-Disk 2.2 Bel 2-Disk 2.4 Bel -Random Read/Write 1-Disk 2.4 Bel2-Disk 2.6 Bel ENVIRONMENTAL SPECIFICATIONSTemperature-Operating 5 ~ 55 ºC-Non-operating -40 ~ 70 ºCHumidity (non-condensing)-Operating 5 ~ 90 %-Non-operating 5 ~ 95 %Linear Shock (1/2 sine pulse)-Operating, 2ms 300G-Non-operating, 1ms 1000GVibration (swept sine, 1/4 octave per minute) Operating5 ~ 500 Hz 1.0 Go-p Non-operating 10 ~21 Hz 0.195 in(double amp) 21 ~ 500Hz 5 Go-p500~800Hz 3 Go-pAltitude (relative to sea level)-Operating -1000 to 10000 ft-Non-operating -1400 to 40000 ftPOWER REQUIREMENTS Voltage +5V±5%Spin Up (max.) 4.5 WSeek (typ.) 5 2.1 W Read/Write On-Track (typ.) 2.0 WLow Power Idle (typ.) 0.65 WStandby (typ.) 0.25 WSleep (typ.) 0.15 WPHYSICAL DIMENSIONHeight 0.37 inWidth 3.94 inDepth 2.75 inWeight 0.22 lb *Notes:Design and specifications are subject to change without prior notice
Spinpoint M60 series • Device Initiated Power Management • 60GB Formatted Capacity Per Disk • GMR/TuMR head with wireless suspension design • Fluid Dynamic Bearing Spindle Motor Technology • Load/Unload Head Technology • ATA Security Mode Feature Set • ATA SMART Feature Set • ATA Automatic Acoustic Management Feature Set • ATA Device Configuration Overlay Feature Set • Multi-Burst On-The-Fly Error Correction • Hybrid Latch System for Reliability and Quietness • SilentSeekTM40.0/60.0/80.0/100.0/120.0GB Capacity 1 Model40GB HM040HC 60GBHM060HC 80GBHM080IC 120GBHM120JC 100GBHM100JC 1. 1MB=1,000,000 Bytes 1GB=1,000,000,000 Bytes *Accessible capacity may vary as some OS uses binary numbering system for reported capacity2. Upper 128 KB is used for firmware 3. Power-On to Drive Ready 4. 30% duty cycle, random seek 5. Unless otherwise specified, specifications are for 2-disk configuration *Notes:Design and specifications are subject to change without prior notice DRIVE CONFIGURATIONInterface ATA 6Buffer DRAM Size 2 8 Mbytes Bytes per Sector 512PERFORMANCE SPECIFICATIONSRead Seek Time (typ.)-Track to Track 2 ms-Average 12 ms-Full Stroke 22 ms-Average Latency 5.6 ms-Rotational Speed 5,400 rpmData Transfer Rate-Media to/from Buffer (max.) 495Mb/s-Buffer to/from Host (max.) 100MB/s-Drive Ready Time (typ.) 3 4 sec RELIABILITY SPECIFICATIONSNon-recoverable Read Error 1 sector in 10 14bits MTBF 330,000 POHControlloed Ramp L/UL 600,000ACOUSTICS (AVERAGE SOUND POWER) -Idle 1-Disk 2.2 Bel 2-Disk 2.4 Bel -Random Read/Write 1-Disk 2.4 Bel2-Disk 2.6 Bel ENVIRONMENTAL SPECIFICATIONSTemperature-Operating 5 ~ 55 ºC-Non-operating -40 ~ 70 ºCHumidity (non-condensing)-Operating 5 ~ 90 %-Non-operating 5 ~ 95 %Linear Shock (1/2 sine pulse)-Operating, 2ms 300G-Non-operating, 1ms 1000GVibration (swept sine, 1/4 octave per minute) Operating5 ~ 500 Hz 1.0 Go-p Non-operating 10 ~21 Hz 0.195 in(double amp) 21 ~ 500Hz 5 Go-p500~800Hz 3 Go-pAltitude (relative to sea level)-Operating -1000 to 10000 ft-Non-operating -1400 to 40000 ftPOWER REQUIREMENTS Voltage +5V±5%Spin Up (max.) 4.5 WSeek (typ.) 5 2.1 W Read/Write On-Track (typ.) 2.0 WLow Power Idle (typ.) 0.65 WStandby (typ.) 0.25 WSleep (typ.) 0.1 WPHYSICAL DIMENSIONHeight 0.37 inWidth 3.94 inDepth 2.75 inWeight 0.22 lb
Spinpoint M40S series • 40GB Formatted Capacity Per Disk • GMR head technology with wireless suspension design • Ultra ATA-100 Interface Serial ATA 1.5Gbps • Fluid Dynamic Bearing Spindle Motor Technology • Load/Unload Head Technology • ATA Security Mode Feature Set • ATA SMART Feature Set • ATA Automatic Acoustic Management Feature Set • ATA Device Configuration Overlay Feature Set • Multi-Burst On-The-Fly Error Correction • SilentSeek™ • Hybrid Latch System for Reliability and Quietness40.0/60.0/80.0GB Capacity 1 Model40GB HM040HI 60GBHM060II 80GBHM080JI 1. MB=1,000,000 Bytes 1GB=1,000,000,000 Bytes *Accessible capacity may vary as some OS uses binary numbering system for reported capacity2. Upper 128 KB is used for firmware 3. Power-On to Drive Ready 4. 30% duty cycle, random seek 5. Unless otherwise specified, specifications are for 2-disk configuration *Notes:Design and specifications are subject to change without prior notice DRIVE CONFIGURATIONInterface SATA 1.5GbpsBuffer DRAM Size 2 8 Mbytes Bytes per Sector 512PERFORMANCE SPECIFICATIONSRead Seek Time (typ.)-Track to Track 2 ms-Average 12 ms-Full Stroke 22 ms-Average Latency 5.6 ms-Rotational Speed 5,400 rpmData Transfer Rate-Media to/from Buffer (max.) 428Mb/s-Buffer to/from Host (max.) 150MB/s-Drive Ready Time (typ.) 3 4 sec RELIABILITY SPECIFICATIONSNon-recoverable Read Error 1 sector in 10 14bits MTBF 330,000 POHControlloed Ramp L/UL 600,000ACOUSTICS (AVERAGE SOUND POWER) -Idle 1-Disk 2.2 Bel 2-Disk 2.4 Bel -Random Read/Write 1-Disk 2.4 Bel2-Disk 2.6 Bel ENVIRONMENTAL SPECIFICATIONSTemperature-Operating 5 ~ 55 ºC-Non-operating -40 ~ 70 ºCHumidity (non-condensing)-Operating 5 ~ 90 %-Non-operating 5 ~ 95 %Linear Shock (1/2 sine pulse)-Operating, 2ms 300G-Non-operating, 1ms 900GVibration (swept sine, 1/4 octave per minute) Operating5 ~ 500 Hz 1.0 Go-p Non-operating 10 ~21 Hz 0.195 in(double amp) 21 ~ 500Hz 5 Go-p500~800Hz 3 Go-pAltitude (relative to sea level)-Operating -1000 to 10000 ft-Non-operating -1400 to 40000 ftPOWER REQUIREMENTS Voltage +5V±5%Spin Up (max.) 4.5 WSeek (typ.) 4 2.1 W Read/Write On-Track (typ.) 2.0 WLow Power Idle (typ.) 0.65 WStandby (typ.) 0.25 WSleep (typ.) 0.15 WPHYSICAL DIMENSIONHeight 0.37 inWidth 3.94 inDepth 2.75 inWeight 0.22 lb