Samsung Ds 24d Keyset User Guide

17
DIALING FEATURES
SPEED DIALING You can dial a preprogrammed telephone number stored in the system-wide
speed dial list of numbers 500–799 or from your personal list of numbers
00–49:
With the handset on-hook, press the SPDkey or dial 16.
Dial the desired speed dial number.
The telephone number is automatically dialed for you.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the
handset or press the SPEAKERkey before you begin dialing.PROGRAMMING PERSONAL SPEED
DIAL...

2. The saved telephone number is stored in memory until you save anoth-
er number.
3. Redial does not apply to intercom calls.CHAIN DIALINGYou may manually dial additional digits following a speed dial number or
chain as many speed dial numbers together as required:
After the first speed number is dialed, press SPDagain and dial anoth-
er speed number ORmanually dial additional digits following a speed
dial number.AUTOMATIC REDIAL/RETRYWhen you are making an outside call and you receive a busy signal,...

MEET ME PAGELift the handset.
Press the Meet Me Page (MMPG) key or dial 54.
Dial the desired zone number.
After the attention tone, instruct the paged person to dial 56.
Press WAITor TRANSFER.
Remain off-hook until the person dials 56from any phone.
The paged person will be automatically connected with you.CALL PARK AND PAGEWhen you have an outside call for someone who is not at his/her desk, you
can park the call and page the requested party:
While in conversation, press the PARKbutton. The call...

23
CONVENIENCE FEATURES
DO NOT DISTURBUse this feature when you want to block calls to your keyset.
While on-hook, press the DNDkey or dial 401. The DNDkey lights
steady red to remind you of this mode.
To cancel DND, press the DNDkey again or dial 400. The DNDlight
turns off. You can make calls while in the DND mode.
NOTES:
1. If the Hot Keypad feature has been turned off, you must first lift the hand-
set or press the SPEAKERkey.
2. If you place your keyset in DND mode and you do not have a DNDkey,...

CALLING THE DOOR PHONE/ROOM
MONITORYou may call the door phone and listen to what may be happening outside
or in another room.
Dial the extension number of the door phone.
You will be connected to the door phone and you can listen or have a
conversation.
If an electric door lock release is installed, dial 13to unlock the door.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the
handset or press the SPEAKERkey.EXECUTIVE/SECRETARY HOT LINEIf programmed, an executive and a...

27 When you receive an off-hook voice announcement, if you are using the
handset, you will hear the announcement in the handset receiver. If you are
using the speakerphone, you will hear the announcement over the keyset
speaker. In both cases, you can continue to speak to the original party.
Press the flashingCALLbutton on your keyset. This will place the origi-
nal party on hold and allow you to talk to the announcing party.
To return to your first party, press the key corresponding to your original...

Press TRANSFERto store your selection.
NOTE: Intercom calls can be automatically put on hold by pressing
TRANSFER.HEADSET OPERATIONKeyset users can switch between headset mode and handset mode. When
using headset mode, press the SPEAKERkey to answer and release calls.
With the handset on-hook, press TRANSFERand then dial 110.
Dial 21to use the headset or 20to use the handset.
Press TRANSFERto store your selection.
Your keyset may be equipped with a Headset mode key. If it is so equipped
pressing this...

31
DISPLAY FEATURES
INTERACTIVE DISPLAY KEYSThe three keys below the display are substitutes for dedicated feature keys
and access codes. Pressing one of these keys has the same effect as press-
ing a programmable key. These keys are called soft keys as their functions
are not fixed. They change to present you with the best options for that call
condition. The use of soft keys allows the programmable keys to be used for
more DSSand speed dial keys.
The SCROLLkey is used to display options available to...

AUTO TIMERDisplay keyset users may have the timer automatically start when they
answer incoming calls or after a short delay on an outgoing call.
With the handset on-hook, press TRANSFERand then dial 110.
Dial 11to turn the auto timer on or 10to turn it off.
Press TRANSFERto store your selection.TIMER FUNCTIONDisplay keyset users may use this feature as a simple stopwatch.
When the keyset is idle, press the TIMERbutton to start timing.
Press the TIMERbutton again to stop timing.
Read the elapsed...

STATION NAMESYou can assign an 11 character name to your keyset. This allows other dis-
play keyset users to call you using the directory dial feature.
To program a station name:
Press TRANSFERand then dial 104.
Enter the 11 character name using the procedure described in Alarm
Reminder Messages
.
Press TRANSFERto store the name.MANAGING KEY ASSIGNMENTSYou can view your key assignments and add extenders to some of your pro-
grammable keys for easy one touch operation of frequently used features.
An...