Samsung Dms 400 User Manual

setting up your dishwasher _11
01 setting up your dishwasher
0~35mm
87 35
605
598845Level
Make sure that the dishwasher is 
level using a leveling tool.
Remove the four protective pieces 
of rubber.
CAUTION
1
C
b
A
Aqua stop  
(models: dmS400TR/  dmS500TR/d146)
A
b
C
2Make sure that the hoses are not bent when 
you insert the dishwasher into its location in 
your kitchen unit
.
CAUTION
A: MAXIMUM DRAIN CONNECTION LENGTH 2.9 M
B: MAXIMUM SUPPLY CONNECTION LENGTH 1.5 M
C: MAXIMUM POWER CONNECTION LENGTH...

12_ setting up your dishwasher
setting up your dishwasher
freesTAnDInG BuILT-In TyPe InsTALLATIon
1
589 mm
Remove the four 
protective pieces of 
rubber. Cut the plinthfacia lower rubber (protective panel) 
to a width of 589 mm.
Insert part “a”.
a
Cut the rubber (part “a”) to the same height of as the 
level of your dishwasher.
UserManual-DMS400TR_EN.indd   125/11/2010   2:40:16 PM 

setting up your dishwasher _13
01 setting up your dishwasher
221
Remove the two screws at the 
top left and right at the front of the 
dishwasher and separate the Top 
Bracket. 
Reassemble the two screws.
Remove the two screws at the top 
left and right at the back of the 
dishwasher and separate the Top 
Table.
3
815
605
605
600
598
A: MAXIMUM DRAIN CONNECTION LENGTH 2.9 M
B: MAXIMUM SUPPLY CONNECTION LENGTH 1.5 M
C: MAXIMUM POWER CONNECTION LENGTH 1.6 M
Attach the foam tape (part “b”) to the 
top of...

14_ setting up your dishwasher
setting up your dishwasher
using the cable clamp
Hoses can be fixed using the Cable Clamp.
using the cable tie
The power cord can be tied using the Cable Ties.
PoWer sourCe
This product operates on a AC 220 ~ 230 V / 50 Hz power source.
c
d
e
0~35mm
Gap:5mm
Level
•	Make sure that the dishwasher is level using a leveling tool.
•	
Please make sure to follow the recommended measurements for the 
installation.CAUTION
4
UserManual-DMS400TR_EN.indd   145/11/2010   2:40:17 PM 

setting up your dishwasher _15
ConneCTInG The hose
•	Connect the appliance to the water mains using a new set of hoses. Do no\
t reuse the old hoses.
Water supply hose
1. Turn off the water supply.
2.  Fasten the water supply hose (or aqua stop) to the inlet 
connector tightly.
3.  Turn on the water supply.
Drain hose
1. If you use only the drain hose for drainage, place and install 
it below 80 cm from the ground.
If the drain hose is installed higher than 80 cm, dirty water 
may flow back or a...

16_ setting up your dishwasher
setting up your dishwasher
ConTroL PAneL
pROGRAm 
SeleCTORYou can select the appropriate wash program depending on the soil level of 
your dishes. When a program is selected, the indicator for that program is lit.
dISplA y Displays the remaining wash time, the wash information (Delay start, Salt refill, 
Rinse refill, Child lock), and error messages.
If an error occurs during an operation, an error message is displayed with a 
warning sound. Refer to the information in the...

setting up your dishwasher _17
START/ReSeTPress this button to start the selected program.
When the door is opened while the dishwasher is operating, the Pause 
function is activated. 
When the Pause function is activated, only the power button works. 
To deactivate the Pause function, close the door.
If you want to reset the selected program, press the Start/Reset button for 3 
seconds.
pOWeR When pressed, all indicator lights turn on and off and the most recently 
finished program light is lit.
When...

18_ setting up your dishwasher
ProGrAm seLeCTor
•	The indicator changes each time the button is pressed.
•	 Press the select button to select one of the seven available wash programs.
•	 By pressing the select button, the program is selected in the order of “Normal → Quick → Pots & Pans 
→ Crystal → Eco → Prewash → Rinse Dry”.
DIsPLA y
1. When additional rinse and drying cycles, Half Load, 4 in 1, Sterilizatio\
n, Child Lock or Delay Start are 
selected, the respective indicators are lit.
2.  When “Rinse...

using your dishwasher _19
using your dishwasher
sALT ConTAIner seTTInG
Filling the salt container with special salt
1. Turn the cap anti-clockwise to remove it.
2.  Fill the salt container with salt. Use a funnel or similar mechanism to \
easily and cleanly fill the 
container.
3.  After filling the container, wipe off any spilled salt to seal the cap properly.
4.  Screw the cap tightly to prevent any suds from penetrating that may cause a water softening 
problem.
Using special salt
Prior to using the...

20_ using your dishwasher
using the salt container
•	 Your	dishwasher	is	equipped	with	an	adjustable	water	softening	system. To avoid scale deposits on the dishes and in the dishwasher, the dishes should be washed 
with soft water, i.e. water with a low lime content. 
The salt container should be adjusted according to the hardness of the water in your area. 
Your local Water Authority can advise you on the hardness of the water in your area.
•	 If	you	want	to	change	the	water	softening	level,	you	should...