Samsung CLP 315W User Manual

							Safety information_11
European Radio Approval Information
(for products fitted with EU-approved radio devices)
Low power, Radio LAN type devices (radio frequency (RF) wireless communication devices), operating in the 2.4 GHz/5 GHz band, may be 
present (embedded) in your printer system which is intended for home or office use. This section is only applicable if these devices are 
present. Refer to the system label to verify the presence of wireless devices.
Wireless devices that may be in your system are only qualified for use in the European Union or associated areas if a CE mark with  a 
Notified Body Registration Number and the Alert Symbol is on the system label.
The power output of the wireless device or devices that may be embedded in you printer is well below the RF exposure limits as set by the 
European Commission through the R&TTE directive.
European States qualified under wireless approvals:
EU Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France (with frequency restrictions), 
Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, The Netherlands, Poland, 
Portugal, Slovakia, Slovenia, Spain, Sweden and the U.K.
EEA/EFTA countriesIceland, Liechtenstein, Norway and Switzerland
European States with restrictions on use:
EUIn France, the frequency range is restricted to 2446.5-2483.5 MHz for devices above 10 mW transmitting power 
such as wireless
EEA/EFTA countriesNo limitations at this time.
REGULATORY COMPLIANCE STATEMENTS
Wireless Guidance
Low power, Radio LAN type devices (radio frequency (RF) wireless communication devices), operating in the 2.4 GHz/5 GHz Band, may be 
present (embedded) in your printer system. The following section is a general overview of considerations while operating a wireless device.
Additional limitations, cautions, and concerns for specific countries are listed in the specific country sections (or country group sections). The 
wireless devices in your system are only qualified for use in the countries identified by the Radio Approval Marks on the system rating label. If 
the country you will be using the wireless device in, is not listed, contact your local Radio Approval agency for requirements. Wireless devices 
are closely regulated and use may not be allowed.
The power output of the wireless device or devices that may be embedded in your printer is well below the RF exposure limits as known at this 
time. Because the wireless devices (which may be embedded into your printer) emit less energy than is allowed in radio frequency safety 
standards and recommendations, manufacturer believes these devices are safe for use. Regardless of the power levels, care should be taken 
to minimize human contact during normal operation.
As a general guideline, a separation of 20 cm (8 inches) between the wireless device and the body, for use of a wireless device near the body 
(this does not include extremities) is typical. This device should be used more than 20 cm (8 inches) from the body when wireless devices are 
on and transmitting.
This transmitter must not be collocated or operation in conjunction with any other antenna or transmitter.
Some circumstances require restrictions on wireless devices. Examples of common restrictions are listed below:
Radio frequency wireless communication can interfere with equipment on commercial aircraft. Current aviation regulations require wireless 
devices to be turned off while traveling in an airplane. IEEE 802.11 (also known as wireless Ethernet) and Bluetooth communication devices 
are examples of devices that provide wireless communication.
In environments where the risk of interference to other devices or services is harmful or perceived as harmful, the option to use a wireless 
device may be restricted or eliminated. Airports, Hospitals, and Oxygen or flammable gas laden atmospheres are limited examples where use 
of wireless devices may be restricted or eliminated. When in environments where you are uncertain of the sanction to use wireless devices, 
ask the applicable authority for authorization prior to use or turning on the wireless device.
Every country has different restrictions on the use of wireless devices. Since your system is equipped with a wireless device, when traveling 
between countries with your system, check with the local Radio Approval authorities prior to any move or trip for any restrictions on the use of 
a wireless device in the destination country.
If your system came equipped with an internal embedded wireless device, do not operate the wireless device unless all covers and shields are 
in place and the system is fully assembled.
Wireless devices are not user serviceable. Do not modify them in any way. Modification to a wireless device will void the authorization to use 
it. Contact manufacturer for service.
Only use drivers approved for the country in which the device will be used. See the manufacturer System Restoration Kit, or contact 
manufacturer Technical Support for additional information.
Downloaded From ManualsPrinter.com Manuals 
						

							12_Safety information
OPENSSL LICENSE
Copyright (c) 1998-2001 The OpenSSL Project. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1.Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 
2.Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the 
documentation and/or other materials provided with the distribution.
3.All advertising materials mentioning features or use of this software must display the following acknowledgment: This product includes 
software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)
4.The names OpenSSL Toolkit and OpenSSL Project must not be used to endorse or promote products derived from this software 
without
5.prior written permission. For written permission, please contact [email protected].
6.Products derived from this software may not be called OpenSSL nor may OpenSSL appear in their names without prior written 
permission of the OpenSSL Project.
7.Redistributions of any form whatsoever must retain the following acknowledgment: This product includes software developed by the 
OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/)
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT ``AS IS AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT 
NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN 
NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, 
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR 
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, 
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE 
USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
This product includes cryptographic software written by Eric Young([email protected]). This product includes software written by Tim 
Hudson ([email protected]).
ORIGINAL SSLEAY LICENSE
Copyright (C) 1995-1998 Eric Young ([email protected]) All rights reserved.
This package is an SSL implementation written by Eric Young ([email protected]). The implementation was written so as to conform with 
Netscapes SSL.
This library is free for commercial and non-commercial use as long as the following conditions are aheared to. The following conditions apply 
to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL documentation included with 
this distribution is covered by the same copyright terms except that the holder is Tim Hudson ([email protected]). Copyright remains Eric 
Youngs, and as such any Copyright notices in the code are not to be removed. If this package is used in a product, Eric Young should be 
given attribution as the author of the parts of the library used. This can be in the form of a textual message at program startup or in 
documentation (online or textual) provided with the package.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1.Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer.
2.Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the 
documentation and/or other materials provided with the distribution.
3.All advertising materials mentioning features or use of this software must display the following acknowledgement: This product includes 
cryptographic software written by Eric Young ([email protected]) The word cryptographic can be left out if the rouines from the library 
being used are not cryptographic related:-). 
4.If you include any Windows specific code (or a derivative thereof) from the apps directory (application code) you must include an 
acknowledgement: This product includes software written by Tim Hudson ([email protected])
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ``AS IS AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED 
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN NO EVENT 
SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, 
DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, 
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, 
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
The licence and distribution terms for any publically available version or derivative of this code cannot be changed. i.e. this code cannot simply 
be copied and put under another distribution licence [including the GNU Public Licence.
Downloaded From ManualsPrinter.com Manuals 
						

							Safety information_13
Downloaded From ManualsPrinter.com Manuals 
						

							14_Contents
contents
2 Features of your new laser product
5 Safety information
INTRODUCTION
16
 16 Printer overview
16 Front view
16 Rear view
 17 Control panel overview
 18 Understanding the control panel
18 LEDs
18Stop button
 19 Supplied software
 19 Printer driver features
19 Printer driver
GETTING STARTED
20
 20 Setting up the hardware
 20 Printing a demo page
 21 System requirements
21 Windows
21 Macintosh
21 Linux
 21 Setting up the network
22 Supported operation environments
 22 Using a wired network
22 Printing Configuration report
22 Setting IP address
23 Network parameter setting
23 Installing the driver software
 23 Using a wireless network(windows/CLP-310W, CLP-315W only)
24 Checking your network environments
24 Installing the printer on an Ad-Hoc wireless network
25 Installing the printer on a wireless network with an Access Point
 26 Using a wireless network(CLP-310W, CLP-315W only)
26 Checking your Network Environments
27 Printing Configuration report
27 Setting IP address
28 Network parameter setting
28 Restoring factory default settings
28 Configuring the machine’s wireless network
29 Installing the driver software
 30 Machines basic settings
30 Altitude adjustment
30 Using the save modes
30 Auto continue
SELECTING AND LOADING PRINT MEDIA
31
 31 Selecting print media
32 Specifications on print media
33 Guidelines for special print media
 34 Changing the size of the paper in the paper tray
 36 Printing on special print materials
 36 Adjusting the output support
 36 Setting the paper size and type
Downloaded From ManualsPrinter.com Manuals 
						

							Contents_15
contents
BASIC PRINTING
37
 37 Printing a document
 37 Canceling a print job
MAINTENANCE
38
 38 Printing reports
 38 Cleaning your machine
38 Cleaning the outside
38 Cleaning the inside
 40 Maintaining the cartridge
40 Toner cartridge storage
40 Handling instructions
40 Use of non-Samsung and refilled toner cartridge
40 Estimated cartridge life
40 Redistributing toner
 41 Replacing the toner cartridge
 42 Replacing the Imaging Unit
 44 Replacing the waste toner container
 45 Maintenance parts
 45 Managing your machine from the website
45 To access SyncThru™ Web Service:
TROUBLESHOOTING
46
 46 Tips for avoiding paper jams
 46 Clearing paper jams
 48 Solving other problems
48 Paper feeding
48
48 Printing problems
49 Printing quality problems
52 Common Windows problems
52 Common Linux problems
53 Common Macintosh problems
ORDERING SUPPLIES AND ACCESSORIES
54
 54 Supplies
 54 How to purchase
SPECIFICATIONS
55
 55 General specifications
 56 Printer specifications
GLOSSARY
57
INDEX
61
Downloaded From ManualsPrinter.com Manuals 
						

							16 _Introduction
introduction
These are the main components of your machine:
This chapter includes:
• Printer overview
• Control panel overview
• Understanding the control panel• Supplied software
• Printer driver features
PRINTER OVERVIEW
Front view Rear view
1Top cover
2Output tray (face down)
3Control panel
4Tray
5Output support
6Front cover release button
7Front cover
8Toner cartridge
9Waste toner container
‘10Imaging unit
1Rear cover release button
2Power switch
3Network porta
a. CLP-310N, CLP-310W, CLP-315N, CLP-315W only.
4USB port
5Power receptacle
6Rear cover
Downloaded From ManualsPrinter.com Manuals 
						

							Introduction_17
CONTROL PANEL OVERVIEW
1wireless LEDShows the status of wireless network. When the LED on, the machine is ready. (Wireless models only)
2status LEDShows the status of your machine. (See Understanding the control panel on page 18 for more information.)
3stopStops an operation at any time and there are more functions. (See Understanding the control panel on page 18 for more information.)
4toner colorsShow the status of each toner cartridge. See Status LED with the toner cartridge messages on page 18.
Downloaded From ManualsPrinter.com Manuals 
						

							18 _Introduction
UNDERSTANDING THE CONTROL PANEL
The color of the status and toner colors LED indicates the machines current 
status.
LEDs
Stop button
STATUSD LEDTONER COLORS LEDDESCRIPTION
lights green all LEDs offThe machine is ready to print.
slowly blinks greenall LEDs offThe machine is receiving data from the computer.
fast blinks greenall LEDs offThe machine is printing data.
lights redall LEDs off• The machine is experiencing an error, such as open cover, empty paper, not installed waste 
toner container, or full waste toner container.
• The machine is experiencing a service required error, such as LSU error, fuser error, or ITB 
error, Contact your sales or service representative.
lights orangeall LEDs off• The machine is experiencing an error such as jammed paper.
• While the machine is booting up, do not open a top cover, since the machine may treat it as an 
error such as paper jam. In this case, open a front cover and close it then, the machine will 
reboot up.
lights greeneach LED blinks redEach toner cartridge is near the end of its life.
blinks redeach LED lights red
Small amount of toner is left in the cartridge. The estimated cartridge lifea of toner is close. Prepare 
a new cartridge for replacement. You may temporarily increase the printing quality by redistributing 
the toner. (See Redistributing toner on page 40.)
lights redeach LED lights red
A toner cartidge has almost reached its estimated cartridge lifea. It is recommended to replace the 
toner cartridge. (See Replacing the toner cartridge on page 41.)
lights greeneach LED blinks red in a 
repeated orderThe machine is warming up.
a. Estimated lifespan means the expected or estimated print cartridge life, which indicates the average capacity of print-outs and is designed pursuant to ISO/
OEC 19752. (See Specifications on page 55.) The number of pages may be affected by operating environment, printing interval, media type, and media size. 
And some amount of torner may remain in the cartridge even when the printer stops printing.
All printing errors will be appear in the Smart Panel program window.
STATUS LEDDESCRIPTION
Printing demo pageIn Ready mode, press and hold this button for about 2 seconds until the status LED blinks slowly, and release.
Printing configuration sheetsIn Ready mode, press and hold this button for about 5 seconds until the status LED blinks fast, and release.
Canceling print jobPress this button during printing. The red LED blinks while the print job is cleared from both the machine and the 
computer, and then the machine returns to ready mode. This may take some time depending on the size of the print job.
Downloaded From ManualsPrinter.com Manuals 
						

							Introduction_19
SUPPLIED SOFTWARE
After you have set up your machine and connected it to your computer, you 
must install the printer software. If you are a Windows or Macintosh OS, 
install the software from the supplied CD and if you are a Linux OS user, 
download the software from the Samsung website (www.samsung.com/
printer) and install.
PRINTER DRIVER FEATURES
Your printer drivers support the following standard features:
• Paper orientation, size, source and media type selection
• Number of copies
In addition, you can use various special printing features. The following 
table shows a general overview of features supported by your printer 
drivers:
Printer driver 
OSCONTENTS
Windows•Printer driver: Use this driver to take full advantage of 
your printer’s features.
•
Smart Panel: This program allows you to monitor the 
machine’s status and alerts you when an error occurs 
during printing.
•SetIP: Use this program to set your machine’s TCP/IP 
addresses. (CLP-310N, CLP-310W, CLP-315N, 
CLP-315W only).    
Linux•Printer driver: Use this driver to run your machine 
from a Linux computer and print documents.
•Smart Panel: This program allows you to monitor 
the machine’s status and alerts you when an error 
occurs during printing.
Macintosh•Printer driver: Use this driver to run your machine 
from a Macintosh computer and print documents.
•Smart Panel: This program allows you to monitor 
the machine’s status and alerts you when an error 
occurs during printing.
Some models or operating system may not support the certain 
feature(s) in the following table.
FEATUREWINDOWSLINUXMACINTOSH
Color modeOO O
Machine quality optionOO O
Poster printingOX X
Multiple pages per sheet 
(N-up)O O (2, 4) O
Fit to page printingOX O
Scale printingOX O
WatermarkOX X
OverlayOX X
Duplex (Manual)OX X
Downloaded From ManualsPrinter.com Manuals 
						

							20 _Getting started
getting started
This chapter gives you step-by-step instructions for setting up the machine.
This chapter includes:
• Setting up the hardware
• Printing a demo page
• System requirements
• Setting up the network• Using a wired network
• Using a wireless network(windows/CLP-310W, CLP-315W only)
• Using a wireless network(CLP-310W, CLP-315W only)
• Machines basic settings
SETTING UP THE HARDWARE
This section shows the steps to set up the hardware which is explained in 
the Quick Install Guide. Make sure you read Quick Install Guide and 
complete following steps.
1.Select a stable location. 
Select a level, stable place with adequate space for air circulation. Allow 
extra space to open covers and trays. 
The area should be well-ventilated and away from direct sunlight or 
sources of heat, cold, and humidity. Do not set the machine close to the 
edge of your desk or table.
 
Printing is suitable for altitudes under 1,000 m (3,281 ft). Refer to the 
altitude setting to optimize your printing. See Altitude adjustment on 
page 30 for more information.
Place the machine on a flat and stable surface, not letting it lean more 
than 2 mm (0.08 inches). Otherwise, it may affect the printing quality. 
2.Unpack the machine and check all the enclosed items.
3.Remove the tape holding the machine tightly.
4.Load paper. (See Changing the size of the paper in the paper tray on 
page 34.)5.Make sure that all the cables are connected to the machine. 
6.Turn the machine on. 
PRINTING A DEMO PAGE
Print a demo page to make sure that the machine is operating correctly.
To print a demo page:
In ready mode, press and hold the Stop button for about 2 seconds.
When you move the machine, do not tilt or turn it upside down. 
Otherwise, the inside of the machine may be contaminated by toner, 
which can cause damage to the machine or bad print quality.
This equipment will be inoperable when mains power fails.
Downloaded From ManualsPrinter.com Manuals