Samsung A800b User Manual

							 4) Green  : Shows the picture in green by  filtering out the red and blue  color signals.
  5) Blue  : Shows the picture in blue by f iltering out the red and green color signals.
Overscan Using this function, you can cut the edge of the picture when u nnecessary information, 
images or noise on the edge of the picture. 
▶ Refer to  "Size Support Mode" . 
 
  1) Off
  2) On
1080P/24fps 
Mode This function displays the full 1080P@24Hz native HD signals wh
ich have 24 frames per 
second with minimal scene distor tions, as in a movie. Though the difference is small, 
this function implements the highest screen quality. 
▶  You can adjust 1080P/24 Frame mode in [HDMI 1] and [HDMI 2] mod es only. 
 
  1) Off  : Displays scenes where 24 frames are lengthened to 60 frames.  Because of 
this process, irregular scenes may be generated. 
  2) On  : Displays scenes where 24 frames are lengthened to 48 frames.  All scenes 
are displayed regularly without any irregular scenes.
Film Mode  Using this function, you can set  the display mode optimized for playing movies when 
watching a movie. Film Mode provides optimal display settings f or movies. 
▶  Film Mode is only supported for [ Video], [S-Video] and [Compone nt 1, 2](480i,576i). 
 
  1) Off
  2) On
 
 
 
|  Input | Picture | Setup | Option | 
 
 
* Click the Play( )/Stop( ) button in the table below to view the  video file. 
Screen 
Adjustment  Description  Play/Stop 
Install To support possible deficiencies i n the installation location, you can invert the projected 
images vertically/horizontally.  
 
  1) Front-Floor  : Normal Image
Downloaded From projector-manual.com Samsung Manuals 
						

							 
 
 2) Front-Ceiling  : Horizontally Reversed Image
  3) Rear-Floor  : Vertically Reversed Image
  4) Rear-Ceiling  : Horizontal/Vertical Reversed Image 
Light Setting  Used to set the image  brightness by adjusting the amount of lig ht generated by the 
lamp.  
 
  1) Theater  : Using this function, you can a djust the light level of the lamp so that you 
can comfortably watch pictures on the screen even when watching  under dark 
conditions. It also lowers power consumption and extends the li fe of the lamp.
  2) Bright  : Used to enhance the brightness in relatively bright ambient  light. Since 
this mode increases the light level of the lamp, you may experi ence more noise 
which is produced when the  projector is cooled down.
Theater  
Bright 
Test Pattern Generated by the projector itself. Utilized as installation bas is for installation of the 
projector.  
 
  1) Crosshatch  : You can check whether the picture is distorted or not.
  2) Screen Size  : You can refer to picture format sizes such as 1.33 : 1 or 1.7 8 : 1.
  3) Color Standard  : You can view the difference by  changing the Color Standard to 
SMPTE_D/HD/EBU. 
  4) Red  : Red Screen, only for color adjustment.
  5) Green  : Green Screen, only f or color adjustment.
  6) Blue  : Blue Screen, only for color adjustment.
  7) White  : White Screen, only f or color adjustment.
  8) 6500K_White  : White Screen, shows brightest white color possible.
 
 
▶ The Crosshatch and Screen Size patterns of this projector are  provided by JKP (JK 
Production).
▶ The Red/Green/Blue colors of the test patterns are only for th e color adjustment 
procedures, and may not comply w ith the actual colors displayed during video 
playback.
Crosshatch 
Screen Size 
Color 
Standard 
Red 
Green 
Blue
White
6500K_White
PC Eliminates or reduces noise that  causes unstable screen quality, such as screen 
trembling. If the noise is not r emoved using Fine Adjustment, a djust the frequency to the 
maximum and then perform F ine Adjustment again.  
 
   
1) Auto Adjustment  : Used to adjust frequency and phase of PC screen 
automatically.
2) Coarse  : Used to adjust frequency when vertical lines appear on PC scr een.
  3) Fine  : Used to fine tune the PC screen.
  4) Zoom  : Used to extend PC screen from the center.
  5) Reset  : Using this function, you can reset the PC menu settings to th e factory 
default settings.
Only activated in the PC environment.
Auto 
Adjustment 
Coarse  
Fine  
Zoom 
Reset 
Color Standard  You may adjust the color standar d to suit the color standard of the input signal. 
 
  1) SMPTE_C  : Standardized for Video Equipme nt by the Society of Motion Picture 
and Television Engineers
  2) HD  : High Definition, 1125 scan lines, standard definition TV subm itted to the 
ITU-R by U.S., Japan and Canada, in 1986.
  3) EBU  : Regulations and standards for  European Broadcasting Productio n and 
Technology, standardized by th e European Broadcasting Union.
Factory DefaultUsing this function, you can reset various settings to the fact ory default settings. 
 
 
 
 
|  Input | Picture | Setup | Option | 
Downloaded From projector-manual.com Samsung Manuals 
						

							 
 
* Click the Play( )/Stop( ) button in the table below to view the video file. 
Screen 
Adjustment  Description  Play/Stop 
language You can select the language used for the menu screen. 
 
Menu Position You can move Menu Position  to up/down/left/right. 
 
Menu 
Translucency You can set the translucency of menu. 
 
1) Opaque
2) High
3) Medium
4) Low
Menu Display 
Time You can set the display time of the menu. 
 
1) 5 sec  5) 90 sec
2) 10 sec  6) 120 sec
3) 30 sec  7) Stay On 
4) 60 sec   
LED Indicator You can enable or disable the  operating LED's on the product. 
 
  1) Off  : This mode disables the operatin g LED. However, the light will light up 
regardless of the LED setting when the power is turned on or of f or when the 
projector is in an abnormal state.
  2) On  : This mode enables the operating  LED so that it can display the current 
operating state of the projector. 
Light Effect  You can turn the LED indicators on your projector on or off acc ording to your 
Downloaded From projector-manual.com Samsung Manuals 
						

							 
 
requirements. 
 
 
  
1) Off  : LED will not come on. 
  2) In Standby  : Turns the LED on in standby mode.
  3) In Watching TV  : Turns the LED on while watching TV. 
  4) Always  : LED will come on after you turn the TV off.
Appears as an ellipse at the top at the back of your projector.
Blue screen  The Blue screen function causes t he screen to change to the Blue screen if there is no 
signal input from the external d evice connected to your project or. 
 
  1) Off
  2) On
Information You can check external source signals, picture setup, PC pictur e adjustment and lamp 
use time.  
 
Downloaded From projector-manual.com Samsung Manuals 
						

							 
 
 |  Before Contacting Service Personnel | 
 
 
   
 Installation and Connection 
 
Symptoms   Troubleshooting 
No Power.
zCheck the power cable connections.  
I want to install my projector to 
the ceiling. 
zThe ceiling installation support  is sold separately. Contact your local product 
distributor.  
External Source is not selected.
zBe sure that the connection cable (video) is properly connected  to the proper 
port. Unless they are connected properly, the device is not ava ilable. 
 
 
   Menu and Remote Control 
 
 
Symptoms   Troubleshooting 
Remote control does not work.
zBe sure that the proper external source is selected.  
zCheck the battery of your remote control. If its size is incorr ect, replace it with 
the recommended battery size. Check whether the polarity of the  installed 
battery is correct.  
zCheck whether your remote control is at a right angle and at th e correct 
distance. Remove any obstacles between your remote control and  the product.  
zDirect lighting of 3-way light bulbs or other lighting device on the remote 
sensor of the projector may affect the sensitivity and cause th e remote control 
to malfunction.  
zCheck if the remote control battery is empty.  
zCheck whether the LED indicator  on the top of the projector is turned on. 
I cannot select a menu.
zCheck if the menu is displayed in gray. A gray-colored menu is  unavailable. 
   
 Screen and External Source 
 
Symptoms   Troubleshooting 
Cannot see picture images.
zBe sure that the power cord of the projector is in place. 
zBe sure that the proper input source is selected. 
zCheck that the connectors are  properly connected to the ports a t the back of 
the projector. 
zCheck the Remote Control batteries. 
zBe sure that the ,  settings are not at thei r lower limit. 
Poor color. 
zAdjust the  and .  
Images are not clear.
zAdjust the focus.  
zCheck that the projection distan ce is either too far or too near to the screen. 
Strange noise.
zIf a strange sound continues, contact our  service center.  
The operating LED is lit up.
zRefer to  Corrective Actions Accor ding to LED Indications.  
Lines appear on screen.
zBecause noise may occur when using your PC, adjust the frequenc y of the 
screen. 
No external device screen is displayed.
zCheck the operating status for the external device and check wh ether the 
Downloaded From projector-manual.com Samsung Manuals 
						

							 
adjustment items, such as the Brightness and the Contrast have been changed 
correctly in the  command screen of the Projector menu.  
Only blue screen appears.
zBe sure to properly connect the  external devices. Check the connection cables 
again. 
Screen appears in black and white or 
odd color./ screen  is too dark or 
bright.
zAs mentioned above, check the adjustment items such as the Brig htness, 
Contrast and Color in the menu.  
zIf you want to restore various settings to their factory defaul ts, run from the menu.  
 
 
Downloaded From projector-manual.com Samsung Manuals 
						

							 
 
 |  Care and Maintenance | Contact SAMSUNG WORLDWIDE | Other |Authority | 
 
 
 
  
   
To clean the exterior and lens of the projector 
 
Clean the projector us ing a soft dry cloth. 
 
Do not clean the projector with flammable 
substances such as benzene, thinners or a wet 
cloth, as these ma y cause problems. 
 
Do not touch the project or with a nail or any 
other sharp objects, as  this may scratch the 
surface.  
   
To clean the interior of the projector 
 
For cleaning the interior o f the projector, ask your 
Service Center or a distributor. (Charged)  
 
Contact your distributor or a Service Center if 
dust or other substances are inside the 
projector. 
 
 
  
Lamp Replacement 
   
Cautions on Lamp Replacement
The projector lamp is an expenda ble supply. For best operating performance, replace the lamp according to 
the usage time. You can view the lamp usage time in the Informa tion Display (INFO button).
Use the recommended lamp when replacing. Lamp specifications are defined in the user’s manual. Replace 
with the same model provided with the projector. 
- Lamp Model Name : LAMP-MERCVRY-Philips
- Lamp Manufacture : Philips Lighting
- Lamp Life Time : 2000Hrs 
- Lamp Type : 300W UHP
Check that the power cord is unp lugged before replacing lamps.
Even after the power cord has been disconnected, the lamp will  be hot. Allow it to cool down for at least 1 
hour before changing the lamp.
The lamp is located at the left rear of your projector.
Before you turn the projector ov er to change the lamp, cover the projector with a soft cloth on a flat surface.
Do not leave the old lamp near inflammables or in reach of chil dren. There is a danger of burn or injury.
Remove dirts or foreign materials around or inside the lamp uni t using a proper vacuum device.
Downloaded From projector-manual.com Samsung Manuals 
						

							 
 
 
  
 
When handling the lamp, avoid to
uching any part of it except for the handles. If you handle the lamp 
incorrectly, it may affect the screen quality and shorten its l ifetime.
  
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLE D  
OR DISPOSED OF ACCORDING TO LOCAL STATE OR FEDERAL LAWS. 
For details see lamprecycle. org , eiae.org, or call 1-800-Samsu ng 
Lamp Replacement Procedure
The lamp is very hot and operates 
with a high voltage. Allow it to 
cool down for at least 1 hour 
after disconnecting the power 
cord before changing the lamp.The lamp is located at the left 
rear of your projector. Place your 
projector so that its left side is 
visible and then remove the 
screws on the lamp cover. 
* Be careful you r projector does 
not fall.Open the cover by holding down 
(A) in the figure and pulling (B).
  
 
Remove the screws (A) in the 
figure and then hold and open 
(B). Remove the screws as shown in 
the figure. As shown in the figure, lift up the 
lamp handles holding them and 
pull the lamp.
 
  
Assembling a new lamp is in the reverse order of the disassembl y.
 
 
  |  Care and Maintenance | Contact SAMSUNG WORLDWIDE | Other |Authority | 
 
 
 
 
If you have any questions or comments relating to Samsung produ cts, 
please contact a SAMSUNG customer care center.  
 
North America  
U.S.A 1-800-SAMSUNG (726-7864) http://www.samsung.com/us
CANADA 1-800-SAMSUNG (726-7864) http://www.samsung.com/ca
MEXICO 01-800-SAMSUNG (726-7864) http://www.samsung.com/mx
 
 
Latin America  
Downloaded From projector-manual.com Samsung Manuals 
						

							 
ARGENTINE 0800-333-3733http://www.samsung.com/ar
BRAZIL 0800-124-421 
4004-0000 http://www.samsung.com/br
CHILE 800-SAMSUNG(726-7864) http://www.samsung.com/cl
COLOMBIA 01-8000112112 http://www.samsung.com.co
COSTA RICA 0-800-507-7267 http://www.samsung.com/latin
ECUADOR 1-800-10-7267 http://www.samsung.com/latin
EL SALVADOR 800-6225 http://www.samsung.com/latin
GUATEMALA 1-800-299-0013 http://www.samsung.com/latin
JAMAICA 1-800-234-7267 http://www.samsung.com/latin
PANAMA 800-7267 http://www.samsung.com/latin
PUERTO RICO 1-800-682-3180 http://www.samsung.com/latin
REP. DOMINICA 1-800-751-2676 http://www.samsung.com/latin
TRINIDAD & TOBAGO 1-800-SAMSUNG(726-7864) http://www.samsung.com/latin
VENEZUELA 0-800-100-5303 http://www.samsung.com/latin
 
 
Europe  
AUSTRIA 0800-SAMSUNG(726-7864) http://www.samsung.com/at
BELGIUM 0032 (0)2 201 24 18 http://www.samsung.com/be
CZECH REPUBLIC 844 000 844 http://www.samsung.com/cz
DENMARK 70 70 19 70http://www.samsung.com/dk
FINLAND 030-6227 515 http://www.samsung.com/fi
FRANCE 3260 SAMSUNG(726-7864) 
08 25 08 65 65(
€ 0,15/Min) http://www.samsung.com/fr
GERMANY 01805-SAMSUNG(726-7864) (€ 0,14/Min)  http://www.samsung.com/de
HUNGARY 06-80-SAMSUNG (726-7864) http://www.samsung.com/hu
ITALIA 800-SAMSUNG (726-7864) http://www.samsung.com/it
LUXEMBURG 0035 (0)2 261 03 710 http://www.samsung.com/be
NETHERLANDS 0900 SAMSUNG(726-7864) (€ 0,10/Min) http://www.samsung.com/nl
NORWAY 815-56 480  http://www.samsung.com/no
POLAND 0 801 801 881 
022-607-93-33 http://www.samsung.com/pl
PORTUGAL 80 8 200 128 http://www.samsung.com/pt
REPUBLIC OF IRELAND 0818 717 100 http://www.samsung.com/ie
SLOVAKIA 0800-SAMSUNG (726-7864) http://www.samsung.com/sk
SPAIN 902 10 11 30 http://www.samsung.com/es
SWEDEN 0771-400 200 http://www.samsung.com/se
SWITZERLAND 0800-SAMSUNG(726-7864) http://www.samsung.com/ch
U.K 0870-SAMSUNG (726-7864) http://www.samsung.com/uk
Downloaded From projector-manual.com Samsung Manuals 
						

							 
 
CIS 
ESTONIA 800-7267 http://www.samsung.ee
LATVIA 800-7267 http://www.samsung.com/lv
LITHUANIA 8-800-77777 http://www.samsung.lt
KAZAKHSTAN 8-10-800-500-55-500 http://www.samsung.kz
KYRGYZSTAN 00-800-500-55-500
RUSSIA 8-800-555-55-55 http://www.samsung.ru
UKRAINE 8-800-502-0000 http://www.samsung.ua
UZBEKISTAN 8-800-120-0-400 http://www.samsung.uz
 
 
Asia Pacific  
AUSTRALIA 1300 362 603  http://www.samsung.com/au
CHINA 800-810-5858 
010-6475 1880 http://www.samsung.com.cn
HONG KONG 3698-4698 http://www.samsung.com/hk
INDIA 3030 8282 
1800 110011 http://www.samsung.com/in
INDONESIA 0800-112-8888 http://www.samsung.com/id
JAPAN 0120-327-527 http://www.samsung.com/jp
MALAYSIA 1800-88-9999 http://www.samsung.com/my
NEW ZEALAND  0800SAMSUNG (726-7864) http://www.samsung.com/nz
PHILIPPINES 1800-10-SAMSUNG (726-7864) http://www.samsung.com/ph
SINGAPORE 1800-SAMSUNG (726-7864) http://www.samsung.com/sg
THAILAND 1800-29-3232 
02-689-3232 http://www.samsung.com/th
TAIWAN 0800-329-999 http://www.samsung.com/tw
VIETNAM 1 800 588 889 http://www.samsung.com/vn
 
 
Middle East & Africa  
SOUTH AFRICA 0860-SAMSUNG (726-7864) http://www.samsung.com/za
TURKEY 444 77 11 http://www.samsung.com/tr
U.A.E 800-SAMSUNG (726-7864) 
8000-4726 http://www.samsung.com/mea
 
 
  |  Care and Maintenance | Contact SAMSUNG WORLDWIDE | Other |Authority | 
 
 
 
 
 Glossary 
 
Downloaded From projector-manual.com Samsung Manuals