Runco Vx3000i Ultra Operation Manual
Have a look at the manual Runco Vx3000i Ultra Operation Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 123 Runco manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
VX-3000 Installation/Operation Manual 77 PREL IMINARY 6.1 RS-232 Connection and Port Configuration To interface the VX-3000 with a home theater automation/control system or a PC running terminal emulation software: 1. Connect it to your control system or PC as shown in Figure 3-17. 2. Start a terminal session on your PC using a terminal-emulation program, such as HyperTerminal. 3. Configure the RS-232 controller or PC serial port as follows: no parity, 8 data bits, 1 stop bit and no flow control. Set the baud rate to 19200. 4. Type a command from among those listed in Table 6-1. For example, to select the Component 1 input, type X133X. Do not send a carriage return after the command. 6.2 Serial Command Syntax Serial commands to the VX-3000 take the following form: • Commands are in ASCII format. • Commands must be in UPPERCASE; for example, X001X, not x001x. • When you send a valid command, the VX-3000 performs the following actions: 1. Echoes the command back to the PC or control system, unless the command is X001X (Power On). 2. Executes the command. 3. Sends a confirmation message in the form X0_[command number]X. The confirmation message does not include the leading zeros in the command. For example, when you send the command X003X, the VX-3000 responds with X003XX0_3X. When you send the command X061X, the VX-3000 responds with X061XX0_61X. When you send the command X133X, the VX-3000 responds with X133XX0_133X. • When you enter an invalid command, the VX-3000 echoes the command and does nothing else. 6. Serial Communications The VX-3000 will not accept serial commands for 20 seconds after it is turned on or off. Table 6-1. Serial Commands: X Command (Write Only) CodeFunction 0x06, 0x14, 0x00, 0x03, 0x00, 0x34, 0x11, 0x00, 0x5cPower on X001XSerial command test action X002XPower off Note Downloaded From projector-manual.com Runco Manuals
Serial Communications 78 VX-3000 Installation/Operation Manual PREL IMINARY X003XMenu X004XEnter X005XExit X006XUp X007XDown X008XLeft X009XRight X011XInfo X021XRemote 1 X022XRemote 2 X023XRemote 3 X024XRemote 4 X025XRemote 5 X026XRemote 6 X027XRemote 7 X028XRemote 8 X029XRemote 9 X030XRemote 0 X041XPicture Memory "Custom 1" X042XPicture Memory "Custom 2" X043XPicture Memory "ISF Day" X044XPicture Memory "ISF Night" X047XPicture Adjust Reset to default X048XSetup Reset to default X049XISF Reset to Default X050Xshow serial number X051Xload gamma 2.2 X052Xremove all msg X053Xcopy comp1 color temperature value to comp2, RGBHD, HDMI1, HDMI2 copy video color temperature value to svideo. X054Xcopy 6500 to CT1 and CT2 Table 6-1. Serial Commands: X Command (Write Only) (continued) Code Function Downloaded From projector-manual.com Runco Manuals
Serial Communications VX-3000 Installation/Operation Manual 79 PREL IMINARY X055Xopen pip window X056XPIP increase sub window size X057XPIP decrease sub windwo size X058XSet PIP active window X059XSet PIP on X060XSet PIP off X061XAspect Ration:16:9 X062XAspect Ration:4:3 X063XAspect Ration:LetterBox X064XAspect Ration:VirtualWide X065XAspect Ration:Cinema X066XAspect Ration:VirtualCinema X067XFor service tool copy ct RGB value X071Xbaud rate = 9600 X072Xbaud rate = 19200 X073Xbaud rate = 115200(default) X081Xshow factory menu X082XImage orientation:floor front X083XImage orientation:ceiling front X084XImage orientation:floor rear X085XImage orientation:ceiling rear X091XLamp ECO Mode X092XLamp Normal Mode X093Xdisable auto source searching X095Xenable printf X096Xdisable printf X100X0 IRE X101X7.5 IRE X102Xprint fan rpm X103Xprint adc values Table 6-1. Serial Commands: X Command (Write Only) (continued) Code Function Downloaded From projector-manual.com Runco Manuals
Serial Communications 80 VX-3000 Installation/Operation Manual PREL IMINARY X106Xcopy comp 720P ADC value to other timing X107Xcopy comp 721P ADC value to other timing( 7.5 IRE) X108Xcopy RGBHD ADC value to other timing X109Xcopy 5160 video ntsc value to pal X110Xcopy 5160 svideo ntsc value to pal X112XColor Temp: 5400 X113XColor Temp: 6500 X114XColor Temp: 9300 X115XColor Temp: Custom1 X116XColor Temp: Custom2 X121XSwitch OSD language 1 English X122XSwitch OSD language 2 French X123XSwitch OSD language 3 Spanish X124XSwitch OSD language 4 German X125XSwitch OSD language 5 Italian X131XCVBS X132XS-Video X133XComp1 X134XComp2 X135XHDMI1 X136XHDMI2 X137XRGBHD X151Xreset user lamp timer X152Xreset factory lamp timer X156XBackground Color = Black X157XBackground Color = Blue X158XBackGround Color = Gray 60 X175XBurn-In mode off X180XBlue Image ON X181XBlue Image OFF Table 6-1. Serial Commands: X Command (Write Only) (continued) Code Function Downloaded From projector-manual.com Runco Manuals
Serial Communications VX-3000 Installation/Operation Manual 81 PREL IMINARY X182XBurn-In on/off eco X183XBurn-In on/off normal X221X32-Gray bars X226XChecker board X231XDMDRedCurtain X232XDMDGreenCurtain X233XDMDBlueCurtain X234XDMDFullBlackCurtain X235XDMDYellowSolidField X236XDMDCyanSolidField X237XDMDMagentaSolidField X252XDMDFullWhiteCurtain X253Xset IRIS full off X254Xset IRIS full on X255Xset dynamic black off X256Xset dynamic black on X260Xtest pattern off X300Xfocus enable X301Xfocus disable X302Xzoom enable X303Xzoom disable X333Xswitch events X400Xshow resolution X500XSet Gamma 2.8 X501XSet Gamma 2.5 X502XSet Gamma 2.2 X503XSet Gamma 1.0 X504XSet Gamma 2.4 X505XSet Gamma 2.6 X520XFocus increment (+1) Table 6-1. Serial Commands: X Command (Write Only) (continued) Code Function Downloaded From projector-manual.com Runco Manuals
Serial Communications 82 VX-3000 Installation/Operation Manual PREL IMINARY X521XFocus decrement (-1) X522XZoom increment (+1) X523XZoom decrement (-1) X524XRVR increment (+1) X525XRVR decrement (-1) X526XH Lens Shift increment (+1) X527XH Lens Shift decrement (-1) X528XV Lens Shift increment (+1) X529XV Lens Shift decrement (-1) X530XH keystone increment (+1) X531XH keystone decrement (-1) X532XV keystone increment (+1) X533XV keystone decrement (-1) X550XDisable Splash screen X551XEnable splash screen X552XDisable OSD message X553XEnable OSD message X570XRead total lamp hours X900Xreset IRIS position X901Xget power status X902Xprojector states X996Xshow composer version X997XShow firmware version X998Xshow mcu version X999Xshow iris version Table 6-1. Serial Commands: X Command (Write Only) (continued) Code Function Downloaded From projector-manual.com Runco Manuals
Serial Communications VX-3000 Installation/Operation Manual 83 PREL IMINARY Table 6-2. Serial Commands: Z Command CodeFunction Z001Lamp hours -- Normal (User OSD) Z002Lamp hours -- ECO (User OSD) Z004Lamp hours -- Normal (Factory OSD) Z005Lamp hours -- ECO (Factory OSD) Z010picture mode setting Z011User brightness Z012User contrast Z014User color Z015User tint Z016User sharpness Z017Color temperature Z034Burn-In On timer Z035Burn-In Off timer Z038Burn-In Cycle Z090select IRE Z091NR_TR Z092Detail Enhance Z093LTI Z094CTI Z104Gamma gain -- Red (adjust ColorTemp) Z105Gamma gain -- Green(adjust ColorTemp) Z106Gamma gain -- Blue(adjust ColorTemp) Z107Gamma offset -- Red(adjust ColorTemp) Z108Gamma offset -- Green(adjust ColorTemp) Z109Gamma offset -- Blue(adjust ColorTemp) Z127DLP Color Wheel delay Z128DLP Degamma Table Z129system works timer Z131R offset to RGBHD(AD9984) Z132G offset to RGBHD(AD9984) Z133B offset to RGBHD(AD9984) Downloaded From projector-manual.com Runco Manuals
Serial Communications 84 VX-3000 Installation/Operation Manual PREL IMINARY Z134R gain to RGBHD(AD9984) Z135G gain to RGBHD(AD9984) Z136B gain to RGBHD(AD9984) Z137Y offset to Comp(AD9984) Z138Pb offset to Comp(AD9984) Z139Pr offset to Comp(AD9984) Z140Y offset to Comp(AD9984) Z141Pb offset to Comp(AD9984) Z142Pr offset to Comp(AD9984) Z143HDMI1 color space Z144HDMI2 color space Z145Splash timer Z146Cine Wide mode Z147Splash Screen ISF or normal Z148Focus Zoom OSD visible Z150select RS232 baudrate Z151Dep Timing Z152Change Timing Tmp Z153RGBHD ADC R offset Z154RGBHD ADC G offset Z155RGBHD ADC B offset Z156RGBHD ADC R gain Z157RGBHD ADC G gain Z158RGBHD ADC B gain Z163comp2 720p ADC R offset Z164comp2 720p ADC G offset Z165comp2 720p ADC B offset Z166comp2 720p ADC R gain Z167comp2 720p ADC G gain Z168comp2 720p ADC B gain Z173comp2 1080p ADC R offset Z174comp2 1080p ADC G offset Table 6-2. Serial Commands: Z Command (continued) Code Function Downloaded From projector-manual.com Runco Manuals
Serial Communications VX-3000 Installation/Operation Manual 85 PREL IMINARY Z175comp2 1080p ADC B offset Z176comp2 1080p ADC R gain Z177comp2 1080p ADC G gain Z178comp2 1080p ADC B gain Z180Red range Z181Green range Z182Blue range Z183Yellow range Z184Cyan range Z185Magenta range Z186Red saturation Z187Green saturation Z188Blue saturation Z189Yellow saturation Z190Cyan saturation Z191Magenta saturation Z200Gamut menu Table 6-3. Serial Commands: U Command CodeFunction U1Set ISF Name (1th~10th word) U2Set ISF Name (11th~20th word) U3Set ISF Name (21th~30th word) U4Set ISF Name (31th~40th word) U5Set ISF Name (41th~50th word) U6Set ISF Name (51th~60th word) U7Set ISF Name (61th~70th word) U8Set ISF Name (71th~80th word) Table 6-2. Serial Commands: Z Command (continued) Code Function Downloaded From projector-manual.com Runco Manuals
Serial Communications 86 VX-3000 Installation/Operation Manual PREL IMINARY Downloaded From projector-manual.com Runco Manuals