Runco Vx 5000ci Projector User Manual

							29
Step 1:Remove the Front Cover (Item 5) by 
loosening #2 Phillips screw below lens.
Step 2:Locate and unplug the Motor Assembly 
Connector (Item 4); remember wire routing   
for the new lens.
Step 3:Locate the six 9/64 Hex Mounting 
Screws (Item 3). Positions are as follows: 
2 @ 12 oclock, 2 @ 9 oclock, 
2 @ 6 oclock.
Step 4:Remove the 6 Mounting Screws (Item 3) 
while supporting the Lens Assembly; 
Lens and Motor Assembly are now free.
Figure 3
Figure 2
Figure 1 
						

							30
Step 5: Remove the Lens and Motor Assembly by 
pulling forward and to the left in order to 
clear the Projector chassis with the Motor 
Assembly.
Step 6: Install new Lens Assembly in reverse 
order. Make sure to route the wire harness 
(Item 4) in original position and away from 
moving lens stages and Motor Assembly to 
prevent unexpected disconnect or lens 
damage.--See Figure 6 Below--
Install New Lens Assembly
VX-5000ci Projector (front view) with Lens Assembly
completely removed.
Figure 6
Figure 5
Figure 4 
						

							31
Basic Troubleshooting Tips
The following is a basic troubleshooting guide that can assist you in resolving typical problems may
result in normal operation. If you have encountered problems that are not listed in this guide, please
contact your Runco dealer for assistance.
The projector does not turn on
after initial installation. The
Power LED on the front of the
Controller stays yellow after the
power button is pressed.
The projector and Controller
are both on, but there is no
video image on-screen.
The projector is producing a
split screen or an otherwise
scrambled image.
The image appears too bright,
and there is a loss of definition
in the brightest areas of the
image.· The RJ-11 (ComLink) cable is
not connected between the
Controller and Projector, or is
made improperly.
· The projector is not plugged in,
or its AC outlet is not active.
Look at its power LED and see if
it is illuminated.
· Incorrect phone cord
· The Controller is on the wrong
source.
· The Controller is on the correct
source, but the source itself is
off.
· A progressive scan DVD is
plugged into Component input
rather than the RGB/Component
input.
· Contrast is set too high.
· The DVD player is set for a
high-level output.
· The video signal has not been
terminated properly somewhere
in the system.· Use a standard RJ-11
phone-type cord. Ensure it is
firmly plugged into both the
Controller and the Projector.
· Ensure there is good conti-
nuity in the RJ-11 cable.
· Verify that the AC outlet is
active, or that the Projector is
plugged in.
· Press MENU on the
Projectors remote, and look
to see which source is active
(the arrow will be pointing to
the active source). Select the
correct source as appropriate.
· Turn on the source. It is rec-
ommended that all sources be
turned on first BEFORE the
VX-5000ci.
· Only NTSC/PAL can be input
to the Component input.
Progressive scan must go into
RGB/Component.
· Turn down the CONTRAST
level on the Controller. Mid-
range is 127; it is recom-
mended to keep it below 140 
to prevent this problem.
· Set the DVD player for a
nominal output (no boost or
gain).
· Ensure all video signals are
terminated in 75 Ohms.
PROBLEM POSSIBLE CAUSE SOLUTION 
						

							The image appears too
washed out, or the darkest
areas of the image appear too
bright.
The colors of the image
appear abnormal
The image appears keystoned
(trapezoidal).
The Projector will not turn on,
and the power LED on the
front of the Controller is
blinking red.
The Projector will not turn
back on after it was powered-
down, or the image disap-
pears during operation.· Brightness is set too high.
· The DVD player may be set
for too high of a brightness
level.
· The Red, Green and/or Blue
outputs of the Controller or
inputs to the Projector are
reversed.
· The Pr and Pb inputs on the
Component input on the
Controller are reversed
· The Projector has been
mounted too high or too low in
respect to its vertical 
offset.
· The Controller may have
locked-up. 
· The Projector will not turn on
for two minutes after power-
down to protect its bulb.
· The bulb has failed· Turn down the BRIGHTNESS
level on the Controller. If possi-
ble, use a PLUGE pattern to set
the brightness level properly.
· Set the DVD player for a nomi-
nal output (no boost or gain).
· Check the cable connections
on the back of the Controller or
on the Projector.
· Adjust Keystone, see page 28. 
· Unplug the Controller for 2
minutes; plug it back in a re-try.
· Perform a system reset on the
Controller (see page 29), and
then re-try.
· Wait two minutes until the LED
on the front of the Controller
turns red.
32
PROBLEM POSSIBLE CAUSE SOLUTION 
						

							33
RS-232 Communications
Baud rate:19200 (fixed)
Bits:8
No Parity
All protocol in ASCII format
RS-232 input connector pin numbers:TxD= Pin# 2, RxD= Pin# 3, GnD= Pin# 5
Command format (single command):command value (i.e. brightness 100).
NO
TE:A space (not an underscore) or comma may be used between the command and its value.
Command string format:command,command value, command etc.
(i.e. COMPOSITE,BRIGHTNESS 100,ANAMORPHIC,)
NO
TE:In between commands, a comma or space may be used
NO
TE:A carriage return must be used after each command or string.
Other notes:
•  For command strings, a maximum of 255 characters can be used in a single string.
•  PARAMETER min/max refers to a functions minimum and maximum value range. Inputting values above or 
below their range may cause unpredictable (but not fatal) results.
General Information 
						

							COMMAND PARAMETER(min/max)Value stored? DESCRIPTION
POWER 0/1 NA Turns DHD On and Off
ON NA NA Turns DHD Controller on
OFF NA NA Turns DHD Controller off
COMPOSITE NA YES Selects the Composite video 
input 
SVIDEO1 NA YES Selects the S-Video 1 input
SVIDEO2 NA YES Selects the S-Video 2 input
COMPONENT NA YES Selects the Component input
HD1 NA YES Selects the RGB HD 1 input
HD2 NA YES Selects the RGB HD 2 input
DVI1 NA YES Selects the DVI 1 input 
DVI2 NA YES Selects the DVI 2 input 
HD1Pass NA YES Selects the HD 1 Pass Thru 
input
HD2Pass  NA YES Selects the HD 2 Pass Thru 
input
ANAMORPHIC NA YES Selects the anamorphic
aspect ratio
STANDARD NA YES Selects the standard (4:3)
aspect ratio
LETTERBOX NA YES Selects the letterbox aspect ratio
VIRTUALWIDE  NA YES Selects the VirtualWide aspect 
ratio
RGBNN NA YES Outputs color space RGB
w/negative, negative sync
RGBPP NA YES Outputs color space RGB
w/positive, positive sync
RGBS NA YES Outputs color space RGB
w/embedded sync on green
YUV NA YES HD YUV output color space
IHPOS -100/100 YES Sets a value for horizontal     
position input
IVPOS -100/100 YES Sets a value for vertical     
position input
IWIDTH -100/100 YES Sets the value for width input
IHEIGHT -100/100 YES Sets the value for height input
OVERSCAN 0/10 YES Sets the overscan value in %
OHPOS -100/100 YES Sets the value for width output
OVPOS -100/100 YES Sets the value for height output
OWIDTH -100/100 YES Sets the value for width output
OHEIGHT -100/100 YES Sets the value for height output
34
RS-232 Commands 
						

							35
COMMAND PARAMETER(min/max)Value stored? DESCRIPTION
!STORE NA YES Stores the current set of values 
(all values) into non-volatile 
memory 
!RESTORE NA YES Restores the stored values
!FACTORY NA YES Restores all values to factory 
default levels
!STATUS NA NA Asks the Controller to provide 
the hardware information,
current values and system status
to the automation system 
!RESTART NA NO Restarts the DHD Controller
(same as turning it on and off)
!ECHO NA NO Enables the Controller to echo 
back commands and values to 
the automation system
!NOECHO NA NO Disables the Controllers
character echoing
!INSTALLMODEOFF NA NA Disables the Installation menu 
(removes it from the main menu)
!INSTALLMODEON NA NA Enables the Installation menu 
(enables it on the main menu)
!SERVICEMODEON NA NA Enables the service mode
!SERVICEMODEOFF NA NA Disable the service mode
RGAIN -30/30 NO Adjust the Red level of image
GGAIN -30/30 NO Adjust the Green level of image
BGAIN -30/30 NO Adjust the Blue level of image
ROFFSET -30/30 NO Adjust the Red level of image
GOFFSET -30/30 NO Adjust the Green level of image
BOFFSET -30/30 NO Adjust the Blue level of image
RGamma -30/30 NO Adjust the Red gamma of image
GGamma -30/30 NO Adjust the Green gamma of 
image
BGamma -30/30 NO Adjust the Blue gamma of image
IRCODE 013 NO Changes the IR Code Set of the
Controller to 013
IRCODE 215 NO Changes the IR Code Set of the
Controller to 215
IRCODE 510 NO Changes the IR Code Set of the
Controller to 510
IRCODE 918 NO Changes the IR Code Set of the
Controller to 918
IRCODE 0 NO Disables the IR receiver 
						

							VX-5000ci Projector Dimensions
36
0
4.879
12.379
20.870
26.304
8.185
1.015
0
2.2
35
18.635
0
24.069
2.235
8.629
Top View
Front ViewBottom View
Side View
Lens Factor
Lens DiameterLens Distance from Chassis
1.57 - 1.95 4.717 1.492
1.95 - 2.74 5.472 Flush with Chassis
2.76 - 4.85 4.474 1.468
4.85 - 7.75 4.724 3.617
0.8:1 Fixed NA NA
Lens Dimensions 
						

							17.5
3.5
11 
DHD Controller Dimensions
Front Panel
Top Panel
37 
						

							38
Specifications
Projector Type:Digital Light Processing™ (DLP)™ Single HD-2 DMD Chip
Native Resolution:1280 x 720 (Designed for 16:9 screens only)
Aspect Ratio:Determined by supplied processor
Video Standards:NTSC, PAL
DTV Compatibility:480p, 720p, 1080i
Scan Frequency:Horizontal: 15-81 KHz, Vertical: 43-100 Hz
Picture Size:Recommended Width: 72-96 in.
Maximum Width: 200 in. wide (16:9 screen)
Throw Distance:Varies per lens - Ranges from 0.8:1 - 7.75:1 (Fixed focal length)
Horizontal/Vertical Offset:Horizontal offset varies per lens, up to 71%
Vertical offset varies per lens, up to 120%
Light Output:1500 ANSI Lumens                  
CSMS Specifications:
Home Theater Calibration: 462-796 ANSI Lumens                   
Foot-Lamberts: 17.2-29.7                                                                       
Contrast Ratio:2500:1 to 3000:1
CSMS Contrast Ratio: 167:1 to 180:1
Lamp:250W NSH
Lamp Life:2000 hours @ 6500
oKelvin
Inputs: Projector:(1) RGB HV, (1) DVI w/HDCP, (1) RS-232                       
Controller:(1) Composite, (1) S-Video, (1) Component, and 
(1) Pass-through
12V Output:See Controller for specifications
Power Requirements:115V AC, 50/60 Hz 100-240V AC, 375W
Operating Environment:40°- 95° F, (5°- 35° C), 0%-90% Humidity (non-condensing)
Dimensions:Width: 20 7/8 in. (530.20 mm)
Depth: 27 7/8 in. (708 mm)
Height: 8 1/4 in. (209.50 mm), with feet 8 7/8 in. (225.40 mm) 
Weight: 73 lbs. (33.1 kg), (without lens)
Regulatory Approvals:Complies with FCC Class B, CE, C-Tick
Limited Warranty: Projector: (2) Two year parts and labor from the date of delivery to the 
end user                  
Lamp Warranty:1000 hours or (6) six months, which ever comes first.
VX-5000ci Projector: